The operation types and operation window for high-purity hydrogen production for the sorption enhanced steam methane reforming in a fixed-bed reactor

The operation types and operation window for high-purity H₂ production for the sorption enhanced steam methane reforming (SE-SMR) with Ni/Al₂O₃ catalyst and CaO sorbent in a fixed-bed reactor are investigated by an experimentally verified 2D numerical method. Four chemical reactions including steam reforming, water gas shift, global steam reforming, and CO₂ sorption are considered. The operation window is defined as the H₂ and CO molar fractions at outlet satisfying both y_H2,out ≥ 90% and y_CO,out ≤ y_CO,allow (= 1%, 2% or 3%) in dry base. Under the conditions of y_H2,out and y_CO,allow, there are six operation types, of which 2 types are within the operation window and 4 types are not within the operation window as the temperature, weight hourly space velocity (WHSV) and steam to methane (S/C) molar ratio vary. For a common case of S/C = 3, the operation windows for y_CO,allow = 3% at WHSV = 8.5 h^?1 and 42.5 h^?1 are located at 570–670 °C and 640–690 °C respectively, based on the parameters in this work. The operation window of temperature is wider with decreasing WHSV, and it becomes wider remarkably as the S/C ratio increases. The lowest temperature inside the operation window is 550 °C. The effects of the temperature, WHSV and S/C ratio on the operating types, y_H2,out and y_CO,out are also presented and discussed in details.     

Nickel‒cobalt bimetallic catalysts prepared from hydrotalcite-like compounds for dry reforming of methane

Ni–Co/Mg(Al)O alloy catalysts with different Co/Ni molar ratios have been prepared from Ni- and Co-substituted Mg–Al hydrotalcite-like compounds (HTlcs) as precursors and tested for dry reforming of methane. The XRD characterization shows that Ni–Co–Mg–Al HTlcs are decomposed by calcination into Mg(Ni,Co,Al)O solid solution, and by reduction finely dispersed alloy particles are formed. H₂-TPR indicates a strong interaction between nickel/cobalt oxides and magnesia, and the presence of cobalt in Mg(Ni,Co,Al)O enhances the metal-support interaction. STEM-EDX analysis reveals that nickel and cobalt cations are homogeneously distributed in the HTlcs precursor and in the derived solid solution, and by reduction the resulting Ni–Co alloy particles are composition-uniform. The Ni–Co/Mg(Al)O alloy catalysts exhibit relatively high activity and stability at severe conditions, i.e., a medium temperature of 600 °C and a high space velocity of 120000 mL g^?1 h^?1. In comparison to monometallic Ni catalyst, Ni–Co alloying effectively inhibits methane decomposition and coke deposition, leading to a marked enhancement of catalytic stability. From CO₂-TPD and TPSR, it is suggested that alloying Ni with Co favors the CO₂ adsorption/activation and promotes the elimination of carbon species, thus improving the coke resistance. Furthermore, a high and stable activity with low coking is demonstrated at 750 °C. The hydrotalcite-derived Ni–Co/Mg(Al)O catalysts show better catalytic performance than many of the reported Ni–Co catalysts, which can be attributed to the formation of Ni–Co alloy with uniform composition, proper size, and strong metal-support interaction as well as the presence of basic Mg(Al)O as support.     

Increased hydroxyl concentration by tungsten oxide modified h-BN promoted catalytic performance in partial oxidation of methane

Hexagonal boron nitride (h-BN) as a layered inorganic nonmetallic material has been widely used. Hydrogen peroxide (H₂O₂) modification can trigger exfoliation and afford abundant B–OH active sites at edge of h-BN, which can enhance methane activation ability. Introducing tungsten oxide (WO₃) to h-BN produces a similar effect, because doping WO₃ into h-BN resulted in electron transfer to N, inducing fracture of B–N bond, resulting in N vacancy (triboron center), exposing more B sites and promoting the generation of B–OH. Significantly, the introduction of WO₃ on the modified h-BN dramatically increased the concentration of B–OH compared with the unmodified h-BN, because H₂O₂ modification weakened B–N bond. By means of XRD, TEM, XPS,EPR, FT-IR, it is proved that the high concentration of B–OH active sites contributed to activating C–H bond, thus methane conversion and CO and H₂ selectivity were significantly improved.     

Economic competitiveness of compact steam methane reforming technology for on-site hydrogen supply: A Foshan case study

On-site hydrogen production through steam-methane reforming (SMR) from city gas or natural gas is believed to be a cost-effective way for hydrogen-based infrastructure due to high cost of hydrogen transportation. In recent years, there have been a lot of on-site hydrogen fueling stations under design or construction in China. This study introduces current developments and technology prospects of skid-mounted SMR hydrogen generator. Also, technical solutions and economic analysis are discussed based on China's first on-site hydrogen fueling station project in Foshan. The cost of hydrogen product from skid-mounted SMR hydrogen generator is about 23 CNY/kg with 3.24 CNY/Nm³ natural gas. If hydrogen price is 60 CNY/kg, IRR of on-site hydrogen fueling station project reaches to 10.8%. While natural gas price fall to 2.3 CNY/Nm³, the hydrogen cost can be reduced to 18 CNY/kg, and IRR can be raised to 13.1%. The conclusion is that skid-mounted SMR technology has matured and is developing towards more compact and intelligent design, and will be a promising way for hydrogen fueling infrastructures in near future.     

Forging furnace with thermochemical waste-heat recuperation by natural gas reforming: Fuel saving and heat balance

This paper considers thermochemical recuperation (TCR) of waste-heat using natural gas reforming by steam and combustion products. Combustion products contain steam (H₂O), carbon dioxide (CO₂), and ballast nitrogen (N₂). Because endothermic chemical reactions take place, methane steam-dry reforming creates new synthetic fuel that contains valuable combustion components: hydrogen (H₂), carbon monoxide (CO), and unreformed methane (CH₄). There are several advantages to performing TCR in the industrial furnaces: high energy efficiency, high regeneration rate (rate of waste-heat recovery), and low emission of greenhouse gases (CO₂, NO_x). As will be shown, the use of TCR is significantly increasing the efficiency of industrial furnaces – it has been observed that TCR is capable of reducing fuel consumption by nearly 25%. Additionally, increased energy efficiency has a beneficial effect on the environment as it leads to a reduction in greenhouse gas emissions.     

Numerical modelling of a low power non-transferred arc plasma reactor for methane conversion

Thermal flow characteristics and the methane conversion reaction in a low power arc plasma reactor for efficient storage and transport of methane, which is the main component of shale gas, were simulated. The temperature and velocity distributions were calculated according to the type of discharge gases and arc current level by a self-developed magnetohydrodynamics (MHD) code and a commercial ANSYS-FLUENT code; the transport of chemical species was analyzed as including the chemical reactions of methane conversion. The simulated results were verified by the comparison of calculated and measured arc voltages with permissible low error as under 4%. Three C₂ hydrocarbon gases with ethane (C₂H₆), ethylene (C₂H₄), and acetylene (C₂H₂) were selected as the converted species of methane from experimental data. The mass fraction of C₂ hydrocarbons and hydrogen as the product of the conversion reaction at the reactor was also calculated. Those values show good agreement with the actual experimental results in that the major conversion reaction occurred in C₂H₂ and hydrogen, and the conversions to C₂H₆, C₂H₄, and hydrogen were minor reactions of methane pyrolysis conversion.     

Prediction of methane adsorption content in continental coal-bearing shale reservoir using SLD model

Shale gas, as an important unconventional resource, has drawn global attention. It is mainly composed of adsorption gas and free gas. Adsorption gas content could play an important guiding role on both the selection of favorable perspective area and the exploration and exploitation of shale gas resources. In order to accurately measure adsorption gas content, a new approach was established to predict the adsorption isotherm of methane on shale. Based on the simplified local-density (SLD) method, both the adsorption isotherms of illite, illite/smectite mixed-layer, cholorite and type III kerogen and the total shale rock could be well fitted. The fitting results show good coincidences with the true experimental test data, which proves the method is reasonable and dependable and the prediction results are effective and credible. In addition, the good simulation results show that the SLD parameters can reflect the pore structure characteristics and corresponding adsorption characteristics of the shale samples, which can be used for the quantitative characterization of shale pore system.     

Two-dimensional thermal analysis of radial heat transfer of monoliths in small-scale steam methane reforming

Monolithic catalysts have received increasing attention for application in the small-scale steam methane reforming process. The radial heat transfer behaviors of monolith reformers were analyzed by two-dimensional computational fluid dynamic (CFD) modeling. A parameter study was conducted by a large number of simulations focusing on the thermal conductivity of the monolith substrate, washcoat layer, wall gap, radiation heat transfer and the geometric parameters (cell density, porosity and diameter of monolith). The effective radial thermal conductivity of the monolith structure, k_r,eff, showed good agreement with predictions made by the pseudo-continuous symmetric model. This influence of the radiation heat transfer is low for highly conductive monoliths. A simplified model has been developed to evaluate the importance of radiation for monolithic reformers under different conditions. A wall gap as thin as 0.05 mm significantly decreased k_r,eff, while the radiation heat transfer showed limited improvement. A pseudo-homogenous two-dimensional model combined with the symmetric model has been developed for a quick evaluation of geometric parameters for a monolith reformers. Monolithic reformers based on highly conductive substrates e.g., Ni and SiC showed great potential for small-scale hydrogen production.     

石英砂介质中甲烷水合物生成过程和相平衡的实验研究

为研究小梯度温度范围内甲烷水合物在石英砂介质中生成过程的热力学和动力学特性,开展了定容条件下273.75K、273.85K、273.95K3种恒温水浴体系的甲烷水合物生成实验。研究结果表明:(1)反应温度越低,釜内甲烷水合物生成过程中反应热释放越快,相比于273.95K的反应体系,273.75K体系的反应釜内首次温度上升值为0.9K,约为273.95K体系的6倍;(2)随反应温度的增加,水合物的生成量和转化率逐渐下降;(3)反应温度越低,甲烷水合过程的前期反应速率越大,气液界面和石英砂表面生成的水合物薄膜阻碍了甲烷气与水之间的进一步传递,使得甲烷的单位消耗速率随反应的进行呈阶梯型递减。通过石英砂介质内甲烷水合物的生成实验,以期为工业上气体水合物的合成、储存与运输提供借鉴。     

Hydrogen production by steam methane reforming in a membrane reactor equipped with a Pd composite membrane deposited on a porous stainless steel

With the aim of producing hydrogen at low cost and with a high conversion efficiency, steam methane reforming (SMR) was carried out under moderate operating conditions in a Pd-based composite membrane reactor packed with a commercial Ru/Al₂O₃ catalyst. A Pd-based composite membrane with a thickness of 4–5 μm was prepared on a tubular stainless steel support (diameter of 12.7 mm, length of 450 mm) using electroless plating (ELP). The Pd-based composite membrane had a hydrogen permeance of 2.4 × 10^?3 mol m^?1 s^?1 Pa^?0.5 and an H₂/N₂ selectivity of 618 at a temperature of 823 K and a pressure difference of 10.1 kPa. The SMR test was conducted at 823 K with a steam-to-carbon ratio of 3.0 and gas hourly space velocity of 1000 h^?1; increasing the pressure difference resulted in enhanced methane conversion, which reached 82% at a pressure difference of 912 kPa. To propose a guideline for membrane design, a process simulation was conducted for conversion enhancement as a function of pressure difference using Aspen HYSYS^®. A stability test for SMR was conducted for ～120 h; the methane conversion, hydrogen production rate, and gas composition were monitored. During the SMR test, the carbon monoxide concentration in the total reformed stream was <1%, indicating that a series of water gas shift reactors was not needed in our membrane reactor system.