Engineering Bioactive M2 Macrophage-Polarized Anti-Inflammatory,Antioxidant, and Antibacterial Scaffolds for Rapid Angiogenesis and Diabetic Wound Repair

Diabetic wound healing still faces great challenges due to the excessive inflammation, easy infection, and impaired angiogenesis in wound beds. The immunoregulation of macrophages polarization toward M2 phenotype that facilitates the transition from inflammation to proliferation phase has been proved to be an effective way to improve diabetic wound healing. Herein, an M2 phenotype-enabled anti-inflammatory, antioxidant, and antibacterial conductive hydrogel scaffolds (GDFE) for producing rapid angiogenesis and diabetic wound repair are reported. The GDFE scaffolds are fabricated facilely through the dynamic crosslinking between polypeptide and polydopamine and graphene oxide. The GDFE scaffolds possess thermosensitivity, self-healing behavior, injectability, broad-spectrum antibacterial activity, antioxidant and anti-inflammatory ability, and electronic conductivity. GDFE effectively activates the polarization of macrophages toward M2 phenotype and significantly promotes the proliferation of dermal fibroblasts, the migration, and in vitro angiogenesis of endothelial cells through paracrine mechanisms. The in vivo results from a full-thickness diabetic wound model demonstrate that GDFE can rapidly promote the diabetic wound repair and skin regeneration, through fast anti-inflammation and angiogenesis and M2 macrophage polarization. This study provides highly efficient strategy for treating diabetic wound repair through designing the M2 polarization-enabled anti-inflammatory, antioxidant, and antibacterial bioactive materials.     

基于软件校准的短波发射机功率控制系统设计

短波发射机功率稳定一直是通信领域致力改善的重点问题,短波发射机功率不稳定会直接影响无线电通信质量,造成通信失真、表达不清晰等问题。针对上述问题,基于软件校准设计短波发射机功率控制系统。该系统借鉴MVC设计模式搭建系统数据库层、业务逻辑层、控制层以及界面显示层基础框架；将功率计与短波发射机相连,实时采集工作状态下的短波发射机功率数据,通过信号处理器实施处理后并存储,借鉴传输元件,将数据发送到控制器,通过控制器校准短波发射机功率与预期之间的偏差,以偏差量为输入,利用改进PID运算得出控制量,生成控制命令,通过输入输出信号接口板输出命令,控制驱动装置调节短波发射机运行参数,实现功率控制。结果表明：与 控制系统、自动调谐系统应用相比较,在所设计系统应用控制下,100s内短波发射机的功率变化曲线与预期曲线之间的拟合优度指数更大,更接近1,优于对比系统,说明相比于对比系统。本系统控制表现更好,更能维持短波发射机功率稳定,达到了研究目标。     

Influence of CO2 inleakage on the slight-alkalization of generator internal cooling water

The slight-alkalization of generator internal cooling water (GICW) is widely used to inhibit the corrosion of hollow copper conductor and thereby ensure the safe operation of the generator. CO₂ inleakage is increasingly identified as a potential security risk for GICW system. In this paper, the influence of CO₂ inleakage on the slight-alkalization of GICW was theoretically discussed. Based on the equilibriums of the CO₂-NaOH-H₂O system, CO₂ inleakage saturation was derived to quantify the amount of the dissolved CO₂ in GICW. This parameter can be directly calculated with the measured conductivity and the [Na⁺] of GICW. The influence of CO₂ inleakage on the slight-alkalization conditioning of GICW and the measurement of its water quality parameters were then analyzed. The more severe the inleakage, the narrower the water quality operation ranges of GICW, resulting in the more difficult the slight-alkalization conditioning of GICW. The temperature calibrations of the conductivity and the pH value of GICW show non-linear correlations with the amount of CO₂ inleakage and the NaOH dosage. This study provides insights into the influence of CO₂ inleakage on the slight-alkalization of GICW, which can serve as the theoretical basis for the actual slight-alkalization when CO₂ inleakage occurs.     

Activation of LSCF–YSZ interface by cobalt migration during electrolysis operation in solid oxide electrolysis cells

High-temperature water electrolysis through solid oxide electrolysis cells (SOEC) will play a key role in building a hydrogen economy in the future. However, the delamination between the air electrode and the electrolyte remains a critical issue to be addressed. Previously, it was hypothesized that Co migration may improve the catalytic activity of the SrZrO₃ second phase at the LSCF-YSZ interface, eventually leading to the delamination. In this work, the LSCF-YSZ interfaces sintered at different temperatures were examined in detail. The activation behaviors of the LSCF electrodes upon application with electrolysis current were characterized under different conditions. Further, samples containing purposely added SrZrO₃ interlayer with and without cobalt were fabricated and compared. The activation process is less significant for the sample with cobalt-added SrZrO₃ interlayer than the sample with pure SrZrO₃ layer, supporting the hypothesis that Co migration may lead to the activation behavior.     

可重构智能表面辅助的四元数调制无线通信系统

四元数调制(Quaternion Modulation,QMod)是一种新型高传输速率的极化调制(Polarized Modulation,PMod)技术,是未来卫星通信系统中极具潜力的多元调制方案之一。QMod将数据块分成4块,其中两块是传输数据信号,另外两块则映射到极化状态部分。每个极化状态块均有一位比特,那么它们可以产生4个极化状态组合。这些状态组合可以用来确定传输数据块在四元数4个不同维度中的位置,从而获得两位额外的传输比特。相比于传统的PMod技术,QMod有着更高的频谱效率。为了进一步挖掘QMod的潜力,介绍了由可重构智能表面(Reconfigurable Intelligent Surface,RIS)辅助的QMod系统,同时推导了该系统的平均误码率理论上界,并在瑞利信道下进行了BER性能仿真。仿真结果表明,RIS辅助的PMod或者QMod系统即便在较低的SNR情况下仍有良好的BER性能,并且随着RIS单元数的增多,其BER性能会逐步提升。     

Ferroelectric and electromechanical performance of diverse engineered states of Mn-doped 0.75Pb(Mg1/3Nb2/3)O3-0.25PbTiO3 ceramics

The materials processing history has a great influence on their properties and finally determines their application effect. In this paper, the ferroelectric, polarization-switching current, and strain properties of Mn-doped 0.75Pb(Mg_1/3Nb_2/3)O₃-0.25PbTiO₃ ceramics were studied in fresh state, aged state, and poled state, respectively. Compared with the symmetric polarization-electric-field (P-E) hysteresis loops, current-density-electric-field (J-E) curves, and bipolar electric-field-induced strain (S-E) curves in fresh state samples, asymmetric P-E loops, J-E curves, and bipolar S-E curves were obtained in poled state samples. Well-aged-state samples exhibit double hysteresis P-E loop, four peaks J-E curves, and symmetric S-E curves without negative strain. The symmetry-conforming short-range order (SC-SRO) principle of point defects and internal electric field E_i is employed to clarify the different phenomenon of three states. Results indicated that randomly oriented defect polarization P_D in aged samples can reverse the spontaneous polarization P_S back and result in the double hysteresis P-E loop and four peaks J-E curves. The oriented P_D and resulting E_i in poled-state samples will lead to the asymmetric loops and strain memory effect.     

Large domain-wall currents in epitaxial Au/BiFeO3/SrRuO3 thin-film capacitors with modulated oxygen vacancy and wall densities

Large domain wall (DW) conductivity in an insulating ferroelectric plays an important role in the future nanosensors and nonvolatile memories. However, the wall current was usually too small to drive high-speed memory circuits and other agile nanodevices requiring high output-powers. Here, a large domain-wall current of 67.8 μA in a high on/off ratio of ~4460 was observed in an epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitor with the minimized oxygen vacancy concentration. The studies from read current-write voltage hysteresis loops and piezo-response force microscope images consistently showed remaining of partially unswitched domains after application of an opposite poling voltage that increased domain wall density and wall current greatly. A theoretical model was proposed to explain the large wall current. According to this model, the domain reversal occurs with the appearance of head-to-head and tail-to-tail 180° domain walls (DWs), resulting in the formation of highly conductive wall paths. As the applied voltage increased, the domain-wall number increased to enhance the on-state current, in agreement with the measurements of current-voltage curves. This work paves a way to modulate DW currents within epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitors through the optimization of both oxygen vacancy and domain wall densities to achieve large output powers of modern domain-wall nanodevices.     

Investigating measurements of fine particle (PM2.5) emissions from the cooking of meals and mitigating exposure using a cooker hood

There is growing awareness that indoor exposure to particulate matter with diameter ≤ 2.5 μm (PM_2.5) is associated with an increased risk of adverse health effects. Cooking is a key indoor source of PM_2.5 and an activity conducted daily in most homes. Population scale models can predict occupant exposures to PM_2.5, but these predictions are sensitive to the emission rates used. Reported emission rates are highly variable and are typically for the cooking of single ingredients and not full meals. Accordingly, there is a need to assess PM_2.5 emissions from the cooking of complete meals. Mean PM_2.5 emission rates and source strengths were measured for four complete meals. Temporal PM_2.5 concentrations and particle size distributions were recorded using an optical particle counter (OPC), and gravimetric sampling was used to determine calibration factors. Mean emission rates and source strengths varied between 0.54—3.7 mg/min and 15—68 mg, respectively, with 95% confidence. Using a cooker hood (apparent capture efficiency > 90%) and frying in non‐stick pans were found to significantly reduce emissions. OPC calibration factors varied between 1.5 and 5.0 showing that a single value cannot be used for all meals and that gravimetric sampling is necessary when measuring PM_2.5 concentrations in kitchens.     

基于参数预标定的长行程PMLSM无传感器控制

为了解决长行程定子不连续永磁直线同步电机存在的因无法全程安装位置传感器和不同动子和定子之间的电磁参数不固定所造成的控制性能下降的难题,提出一种在每一段定子内先进行参数标定,再进行速度控制的控制系统设计。首先,在动子进入过程中,对电机进行电磁参数标定,根据标定参数对控制器参数进行调整,以达到更好的控制效果。然后,使用无位置传感器控制系统使动子快速达到设定速度值并稳定运行。实验结果表明:动子进入过程参数标定精度分别为0.002Wb和0.000 4H;无位置传感器控制中位置估计精度为0.63mm,速度收敛时间为0.45s,稳态误差为0.02m/s。基本满足永磁直线同步电机用于长行程运输的控制快速性、稳定性等要求。     

1H‐decoupling and Isotopic Labeling for the Measurement of the Longitudinal Relaxation Time of Hyperpolarized 13C‐Methylenes in Choline Analogs

The T₁ of a hyperpolarized site in solution is a key parameter that determines the time‐window in which its NMR signals are observable. For ¹³C sites adjacent to protons, ¹H‐decoupling has been shown to increase the hyperpolarized signal resolution and SNR. Additionally, polarization transfer to protons has shown utility in increasing the sensitivity of detection. However, ¹H‐decoupling could lead to a change in the decay rate of a hyperpolarized ¹³C site. Here we tested this possible effect in a case where the protons are directly bound to an sp³ hyperpolarized ¹³C site (using [1,2‐¹³C₂]choline) and ¹H‐decoupling was applied continuously throughout the hyperpolarized decay measurement. We found that ¹H‐decoupling did not lead to any significant changes in the ¹³C polarization decay time but did result in the expected collapse of J‐coupling and produced sharper signals. This result suggested that ¹H‐decoupling did not affect the decay rate of hyperpolarized sp^{3 13}C sites. The deuterium‐substitution approach (using [1,1,2,2‐D₄,1‐¹³C]choline) showed a dramatic prolongation of T₁. Upper bounds on the T₁ of all investigated sites were calculated.