Poly(3-hexylthiophene-2,5-diyl) based diodes for ionizing radiation dosimetry applications

Accurate measurements of radiation dose are essential prerequisites for the safe and effective use of ionizing radiation in diagnostic and therapeutic medical applications. Recently, dosimeters based on organic polymers have been developed for this purpose. In this work, Poly(3-hexylthiophene-2,5-diyl) (P3HT) based organic diodes were evaluated as potential radiation dosimeters by quantifying the radiation-induced photocurrent under various measurement conditions. Control devices were fabricated in which the P3HT was replaced by polystyrene (PS) for the purpose of quantifying the non-photocurrent contribution to the measured signal. Net photocurrent was determined by subtracting the signal from the PS devices from the signal in the P3HT devices under identical measurement conditions. The responses of these devices were tested in various beam qualities: 100 kVp, 180 kVp, 300 kVp and 6 MV, 18 MV photons. The influences of electric field, film thickness and dose rate on dosimeter sensitivity were investigated. The diodes produced a linear increase in current with increasing dose rate. They demonstrated an increase in sensitivity with increased instantaneous dose rate and an increase in sensitivity at the lowest average dose rates studied here. The sensitivities for different energies were 22.9 nC/Gy, 21.8 nC/Gy and 21.4 nC/Gy for 100 kVp, 180 kVp and 300 kVp, respectively; and 14.5 nC/Gy, 14.7 nC/Gy for 6 MV and 18 MV, respectively for device with P3HT thickness 29 μm.     

Alkylated indolo[3,2,1-jk]carbazoles as new building blocks for solution processable organic electronics

A facile strategy for the introduction of tert-butyl and hexyl chains to the indolo[3,2,1-jk]carbazole scaffold is presented. With these building blocks six materials based on three different 4,4′-bis(N-carbazolyl)-1,1-biphenyl derivatives with varying degree of planarization were prepared. Characterization of the materials showed that the alkyl chains have only minor effects on the photophysical properties of the compounds. In contrast, thermal robustness towards decomposition and electrochemical stability are increased by the introduced alkyl chains. Detailed investigation of the solubility in five different solvents revealed that the incorporation of the alkyl chains increases the solubility significantly. The increased solubility of the materials allowed the application as host materials in red, green and sky-blue solution processed phosphorescent organic light emitting diodes. Hence, this work presents the first solution processed light emitting devices based on the indolo[3,2,1-jk]carbazole scaffold.     

Environmentally friendly CsPbBr3 QDs multicomponent glass with super-stability for optoelectronic devices and up-converted lasing

Ultra-stable CsPbBr₃ perovskite quantum dots (QDs) multicomponent glass with high transmittance was prepared by melt-quenching heat treatment. The average diameter of the CsPbBr₃ QDs was ∼1.96 nm. The resulting glass displayed a high exciton binding energy of 362 ± 18 meV. Notably, these glass-encapsulated materials exhibited excellent resistance to heat, light, and water, superior to that of previously reported perovskite-based materials, and underwent an extremely low rate of Pb leaching during water immersion. Based on the glass, a high-performance white light-emitting diode (WLED) device was fabricated with Commission Internationale de L’Eclairage (CIE) coordinates of (0.3156, 0.3326) and color gamut of ∼113 % National Television Standards Committee (NTSC). The CsPbBr₃ QDs glass without rare earth elements further acted as an optical gain medium, realizing up-conversion lasing with 980-nm laser excitation for the first time. The reversible linear fluorescence response indicates that the glass could be a potential candidate for temperature sensors.     

Design of switchable band‐notched frequency selective absorber

An active band‐notched frequency selective absorber (BNFSA) with switchable notch band is proposed in this article. The BNFSA is a two‐layer structure composed of a lossy layer at the top and a ground plane at the bottom, separated by an air spacer. The element of the lossy layer is a lumped‐resistor‐loaded metallic dipole with a parallel LC resonance structure, which is realized by complementary n‐shaped resonator (CnR) inserted in the center, and PIN diode is welded at two arms of CnR. The bias circuit printed on the back of the substrate of the lossy layer connects to anode and cathode of the diode by via hole and isolates by the inductor. Simulation results show that the notch bands are located at 4.50 and 6.81 GHz when the diode sets to ON and OFF, respectively. To validate the performance of switchable BNFSA, the prototypes are fabricated and measured, reasonable agreement between simulated and measured results is obtained.     

Polylactide‐perylene derivative for blue biodegradable organic light‐emitting diodes

In this work we demonstrate, for the first time, the use of polylactic acid (PLA) as a biodegradable host matrix for the construction of the active emissive layer of organic light‐emitting diode (OLED) devices for potential use in bioelectronics. In this preliminary study, we report a robust synthesis of two fluorescent PLA derivatives, pyrene‐PLA ( AH10 ) and perylene‐PLA ( AH11 ). These materials were prepared by the ring opening polymerisation of l ‐lactide with hydroxyalkyl‐pyrene and hydroxyalkyl‐perylene derivatives using 1,8‐diazabicyclo[5.4.0]undec‐7‐ene as catalyst. OLEDs were fabricated from these materials using a simple device architecture involving a solution‐processed single‐emitting layer in the configuration ITO/PEDOT:PSS/PVK:OXD‐7 (35%): AH10 or AH11 (20%)/TPBi/LiF/Al (ITO, indium tin oxide; PEDOT:PSS, poly(3,4‐ethylenedioxythiophene) doped with poly(styrenesulfonic acid); PVK, poly(vinylcarbazole); OXD‐7, (1,3‐phenylene)‐bis‐[5‐(4‐tert‐butylphenyl)‐1,3,4‐oxadiazole]; TPBi, 2,2′,2″‐(1,3,5‐benzenetriyl)tris(1‐phenyl‐1H‐benzimidazole)). The turn‐on voltage for the perylene OLED at 10 cd m^–2 was around 6 V with a maximum brightness of 1200 cd m^–2 at 13 V. The corresponding external quantum efficiency and device current efficiency were 1.5% and 2.8 cd A^–1 respectively. In summary, this study provides proof of principle that OLEDs can be constructed from PLA, a readily available and renewable bio‐source. © 2020 The Authors. Polymer International published by John Wiley & Sons Ltd on behalf of Society of Industrial Chemistry.     

Metasurface based pattern reconfigurable antenna for 2.45 GHz ISM band applications

In this article, a Z‐shaped antenna is designed for 2.45 GHz ISM band applications. The proposed antenna is surrounded by metasurface‐based unit cells. The unit cells are designed to reflect for the proposed frequency. Each of this unit cells are activated with the help of a diode. Unit cell is considered active by switching on the diode of respective unit cell. According to the activation of unit cell the pattern of the antenna will be reconfigured. The 2.45 GHz ISM band pattern reconfigurable microstrip antenna is presented. The radiation pattern of the antenna can be steered toward a desired direction by activating appropriate metasurface unit cell, minimizing the interference and optimizing medium usage. The proposed antenna performance is presented with the help of reflection coefficient and the pattern steerable capability by activating metasurface unit cells. The proposed antenna is having azimuth‐pattern reconfigurable capability around 360°.     

半导体激光器辐照损伤效应实验研究进展

半导体激光器(LD)工作在空间辐射或核辐射环境中时,会受到辐照损伤的影响而导致器件性能退化。文章回顾了不同时期研制的LD(从早期的GaAs LD到量子阱LD和量子点LD)在辐照效应实验方面的研究进展,梳理了国际上开展不同辐射粒子或射线(质子、中子、电子、伽马射线)诱发LD辐射敏感参数退化的实验规律,分析总结了当前LD辐照效应实验方法研究中亟待解决的关键技术问题,为今后深入开展LD的辐照效应实验方法、退化规律、损伤机理及抗辐射加固技术研究提供理论指导和实验技术支持。     

基于PIN光电二极管的个人辐射探测器研制

为使公众能自行探测所处环境的辐射水平，本文利用PIN光电二极管直接测量X/γ射线的原理研制了便携式环境辐射探测系统，该系统采用智能终端控制探测设备。其中，探测模块中设计了弱信号放大电路，控制和通信模块的设计基于无线微控制器。该环境辐射探测器具有低成本、低功耗、体积小、易使用、易组网等特点。经国防科技工业电离辐射一级计量站检定，探测器各项指标均符合国家剂量仪鉴定规程JJG 521-2006的要求。     

Synthesis and characterization of poly (linoleic acid)-g-poly(methyl methacrylate) graft copolymer with applying in Au/PLiMMA/n-Si diode

Poly (linoleic acid)-g-poly(methyl methacrylate) (PLiMMA) graft copolymer was synthesized and characterized. PLiMMA graft copolymer was synthesized from polymeric linoleic acid peroxide (PLina) possessing peroxide groups in the main chain by free radical polymerization of methyl methacrylate. Later, PLiMMA was characterized by proton nuclear magnetic resonance (¹H NMR), gel permeation chromatography (GPC), thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC) techniques. Furthermore, Au/PLiMMA/n-Si diode was fabricated for the purpose of investigating PLiMMA׳s conformity in diodes. The main electrical characteristics of this diode were investigated using experimental current–voltage (I–V) measurements in dark and at room temperature. Obtained results, such as sufficiently high rectifying ratio of 4.5×10⁴, indicate that PLiMMA is a promising organic material for electronic device applications.