超宽带大功率合成器设计北大核心CSCD

在80 MHz~1 GHz频段,单个功率管输出功率能达到100 W以上,为研制输出功率400 W的功率放大器,文中设计了四路功率合成器。该合成器需要实现功率容量大、工作频带宽、体积小的设计目标。在功率容量方面,文中采用悬置带状线结构,其功率容量远远大于微带线结构;在工作频带方面,采用切比雪夫九节阻抗变换器,将工作带宽拓宽为80 MHz~1 GHz;在体积方面,文中合成器的功率合成部分采用Y型节级联实现四路功率合成,阻抗变换部分采用切比雪夫阻抗变换器进行阻抗变换,该结构相较于磁环巴伦功率合成器,不但具有损耗小、平坦度高的优点,而且通过将阻抗变换器设计成曲折的形状,进一步缩小了合成器体积。仿真与实测结果显示该合成器在80 MHz~1 GHz范围内还具有较高的平坦度,合成效率可达90%以上。     

An active balancer with rapid bidirectional charge shuttling and adaptive equalization current control for lithium-ion battery strings

This article proposes an active balancer, which features bidirectional charge shuttling and adaptive equalization current control, to fast counterbalance the state of charge (SOC) of cells in a lithium-ion battery (LIB) string. The power circuit consists of certain bidirectional buck-boost converters to transfer energy among the different cells back and forth. Owing to the characterization of the open-circuit voltage (OCV) vs SOC in LIB being relatively smooth near the SOC middle range, the SOC-inspected balance strategy can achieve more precise and efficient equilibrium than the voltage-based control. Accordingly, a compensated OCV-based SOC estimation is put forward to take into account the discrepancy of SOC estimation. Besides, the varied-duty-cycle (VDC) and curve-fitting modulation (CFM) methods are devised herein to tackle the problems of slow equalization rate and low balance efficacy, which arise from the diminution in balancing current as the SOC difference between the cells decreases in the later duration of equalization especially. The proposed strategies have taken the battery nonlinear characteristic and circuit parameter nonideality into account and can adaptively modulate the duty cycle with the SOC difference to keep balancing current constant throughout the balancing cycle. Simulated and experimental results are given to demonstrate the feasibility and effectiveness of the same prototype constructed. Compared with the fixed duty cycle and the VDC methods, the proposed CFM has the best balancing efficiency of 81.4%, and the balance time is shortened by 27.1% and 18.6%, respectively.     

用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

Single-switch boost-buck DC-DC converter for industrial fuel cell and photovoltaics applications

The realization of dc-dc converters performs a vital function in exploiting renewable energy sources such as solar photovoltaic (PV) and fuel cell applications. This paper demonstrates a single-switch unidirectional buck-boost dc-dc converter for continuous power flow control, excluding the hybrid switched-capacitor. The proposed converter utilizes a limited number of passive components, only four diodes and three inductors required, in addition to six capacitors. The converter can operate at a wide input voltage range with continues input current. The converter has experimented under real-time conditions with 660 W PV system. The obtained efficiency ranges from 93% to 98%. Furthermore, the converter has interfaced with 550 W fuel cell operated under different fuel pressure. The realized efficiency ranges from 91% to 97%. The maximum measured inductance current ripple is limited to under 0.70 A in both scenarios, whereas 0.16 V is the maximum output voltage ripple.     

基于平均功率平衡控制的磁悬浮分子泵电力失效补偿方法

高速磁悬浮涡轮分子泵（Turbo Molecular Pump, TMP）因其高能量密度、微振动、无需润滑等优点被广泛应用于工业领域，但外部电源失效时，高速转子跌落后与保护轴承产生剧烈撞击和摩擦，将给系统带来致命损害。针对以上问题，提出一种基于平均功率平衡法的电力失效补偿控制（Power Failure Compensation Control, PFCC）方法。首先，设计电机能量回馈电路；其次，对Buck-Boost变换器进行数学建模，设计一种双环非线性控制器，其中电流内环使用滑模控制，电压外环使用平均功率平衡控制（Average Power Balance Control, APBC），并利用Lyapunov函数推导出系统的稳定性条件；最后，通过搭建磁悬浮分子泵PFCC实验平台，对所提出的方法进行实验验证。结果表明：本文所提出的方法具有快速响应和输出鲁棒性，磁悬浮转子由额定转速21000 r/min降至3900 r/min时跌落，电机能量转化效率为96.6%，提高了磁轴承系统的安全性。     

Reduced‐order method for mathematical modeling of multiphase dc‐dc converter

A multiphase dc‐dc converter is effective for miniaturization and achieving high‐power density in a switching power supply. However, its mathematical modeling becomes complex as the phase number of the circuit increases. This study proposes a new modeling method to derive a reduced‐order method in a simple manner. The frequency characteristics of the reduced‐order model are fit to those of the original mathematical model of the multiphase dc‐dc converter. Therefore, the efficacy of the proposed method is validated.     

一种可控的自动扶梯电磁铁驱动电路板

扶梯制动系统是扶梯在出现紧急状况下确保乘客安全的重要设施。制动系统中的安全制动是在工作制动器无法在规定的时间内制停扶梯的一个措施,往往是在一些特别危险的场合下被触发,因此对于此制动器的控制显得尤为重要。本文提出了一种新型的自动扶梯制动器电磁铁驱动电路的设计,该设计用纯电子线路替代了传统的电气与电子组合形式,直接由自动扶梯单片机控制单元进行控制。     

Study of planar structure applying reciprocity technique combined with MGEC and analysis of discontinuity

The 3D structure electromagnetic computation presents several difficulties related to the volume mesh. In fact, the entire volume space must be taken into account even the smallest details. In this article, we propose a formulation based on the reciprocity theorem combined with the generalized equivalent circuit method to model a planar 3D structure with both coaxial and planar excitation. The major advantage of this formulation is the fact to reduce the computational volume into 2D ones in the discontinuity plane. In addition, we focused on the calculation of the discontinuity between the excitation source and the planar structure to determine the exact behavior of the electric coaxial excitation model. The obtained current density, electric field distributions, and the input impedance are presented and discussed in the following sections. An approximately good agreement of input impedance with those obtained by the simulator and measurement is shown.     

QKD系统中基于EA电路的诱骗态实现

使用诱骗态量子秘钥方案可以解决因光子数分离攻击而导致的安全漏洞,保证了长距离量子通信的安全。本文介绍了量子通信的相关原理,通过对电吸收调制电路和激光器驱动电路的设计,精确控制产生了1550 nm波段的窄脉冲,经过内部调制成功制备诱骗态光脉冲,其强度约为信号态光脉冲的三分之一,因激光器的同一性而具有一致的光学特征从而避免了时频窃听,并具有强度可调的优点。     

可变磁路式永磁悬浮系统的防跌落防吸附控制

永磁悬浮系统是一种典型的非线性系统,随着导磁体与悬浮物之间的气隙变化,控制特性发生变化,影响系统的稳定性。为防止外界干扰引起系统偏离平衡点时,悬浮物跌落或吸附到导磁体上,提出一种基于气隙变化的防跌落防吸附控制方法。在整个悬浮气隙内选取多点预设悬浮力,基于各设计点预设的悬浮力计算控制参数,并依据插值原理得到完整的防跌落防吸附控制律,有效补偿悬浮物运动时不均匀变化的悬浮力,提高系统的可控性,稳定性和鲁棒性。仿真和实验表明,防跌落防吸附控制方法能缓和冲击,提高防跌落性能,当外扰使气隙变大时悬浮力迅速变大,防止悬浮物跌落,当外扰使气隙变小时悬浮力迅速变小,防止悬浮物吸附于导磁体上。