Effects of Cu on the corrosion behavior and microstructure of Mg–Zn–Ca bulk metallic glass

For the purpose of developing biodegradable magnesium alloys with suitable properties for biomedical applications, Mg–Zn–Ca–Cu metallic glasses were prepared by copper mold injection methods. In the present work, the effect of Cu doping on mechanical properties, corrosion behavior, and glass-forming ability of Mg₆₆Zn₃₀Ca₄ alloy was studied. The experimental findings demonstrated that the incorporation of Cu decreases the corrosion resistance of alloys, but increases the microhardness and degradation rate slightly. However, the addition of a trace amount of Cu can make the samples have antibacterial properties. Therefore, Mg–Zn–Ca–Cu has great advantages in clinical implantation and is the potential implant material.     

An ultrasonic study on ternary xPbO–(45-x)CuO–55B2O3 glasses

A series of xPbO–(45-x)CuO–55B₂O₃ glasses (5 ≤ x ≥ 40 mol %) were prepared by the melt-quenching technique. The X-ray diffraction (XRD) patterns of the prepared glasses are found to have amorphous structure. An extensive ultrasonic study has been made to explore the structural role of PbO and CuO in the borate network. Various elastic properties were calculated from the measured data of density and ultrasonic velocity. Ultrasonic velocity and elastic moduli revealed broad humps at about 20 mol % PbO, which are attributed to the borate anomaly. Below 20 mol % PbO, all Pb²⁺ ions are considered to be entering the borate network as a glass modifier. This results in the transforms the borate network from an open structure to a denser three-dimensional structure due to BO₃ → BO₄ conversion. Beyond 20 mol, addition of PbO results in the formation of metaborate, pyroborate, and orthoborate units with NBOs. This weakness the glass structure and decrease both ultrasonic velocity and elastic moduli. The elastic properties were predicted and quantitatively analyzed by taking into account the effect of boron coordination number on the compositional and structural parameters involved in Makishima–Mackenzie's theory, ring deformation model and bond compression model. An excellent agreement between the computed theoretical and experimental elastic moduli, micro-harness and Poisson's ratio was achieved for majority of samples.     

Preparation and electrochemical characterization of Ti-based amorphous metallic glass with high strength

Ti-based amorphous metallic glasses have excellent mechanical, physical, and chemical properties, which is an important development direction and research hotspot of metal composite reinforcement. As a stable, simple, efficient, and large-scale preparation technology of metallic powders, the gas atomization process provides an effective way of preparing amorphous metallic glasses. In this study, the controllable fabrication of a Ti-based amorphous powder, with high efficiency, has been realized by using gas atomization. The scanning electron microscope, energy-dispersive spectrometer, and X-ray diffraction are used to analyze surface morphology, element distribution, and phase structure, respectively. A microhardness tester is used to measure the mechanical property. An electrochemical workstation is used to characterize corrosion behavior. The results show that as-prepared microparticles are more uniform and exhibit good amorphous characteristics. The mechanical test shows that the hardness of amorphous powder is significantly increased as compared with that before preparation, which has the prospect of being an important part of engineering reinforced materials. Further electrochemical measurement shows that the corrosion resistance of the as-prepared sample is also significantly improved. This study has laid a solid foundation for expanding applications of Ti-based metallic glasses, especially in heavy-duty and corrosive domains.     

Structure,stability and optical parameters of cobalt zinc borate glasses

In this study, the impact of cobalt oxide (CoO) on the structure, stability, linear and nonlinear optical parameters of B₂O₃–Na₂O–ZnO glasses was scrutinized. A series of glass system (ZnCoNaB-glasses) was successfully prepared through the melt quenching approach. Optical absorbance, reflectance, transmittance and FTIR spectroscopy were performed for all ZnCoNaB-glasses. The FTIR results showed that the BO₄ units are enhanced while nonbridging oxygens are decreased with further CoO addition. Furthermore, ZnO exists as four-coordinated [ZnO₄] units and these units decreased with further doping of CoO. These structural variations produce a decreasing impact in Urbach energy and nonlinear refractive index, meanwhile enhance the glass stability. Further, the metallization criterion (M) values indicate that our glass samples can be used for a new generation of nonlinear optical glasses. The preceding results can predict that the investigated ZnCoNaB-glasses will be utilized in versatile applications; especially optical switching and computing.     

Impact of bismuth oxide on the structure,optical features and ligand field parameters of borosilicate glasses doped with nickel oxide

Understanding the impact of bismuth cations on the optical properties of borosilicate glass is significant for manipulating borate glass applications. In this paper, the influence of bismuth cations on both structural and optical properties of borosilicate glass doped with NiO was investigated. Different glass samples, containing different amounts of Bi₂O₃ and a constant amount of NiO, were prepared and studied. Infrared (IR) analysis was carried out to study the internal structure within the investigated glass samples. Optical absorption studies were performed to investigate the impact of Bi₂O₃ content on optical properties of the BiBaNiB-glasses. Astonishingly, with Bi₂O₃ addition, an absorption band at 380 nm has appeared. Moreover, this band is overlapped with the Urbach edge; which regularly produced an artificial edge-like feature at ~450 nm. A detailed deconvolution protocol has been implemented for an appropriate understanding of these spectra and unraveling the hidden Urbach edge. Optical band gap energy, linear and nonlinear refractive index for each BiBaNiB sample were calculated. Furthermore, the metallization criterion was calculated to examine the metallic or insulating nature of the BiBaNiB-glasses. The values of the nonlinear third-order susceptibility and nonlinear refractive index were increased with Bi₂O₃ doping. The BiBaNiB-glasses exhibited outstanding stability and optical band gap than the pristine glass sample, which makes it possible for practical applications.     

Deepening our understanding of bioactive glass crystallization using TEM and 3D nano-CT

One key issue influencing a broader application of Bioglass 45S5 in tissue engineering is its inherent crystallization tendency, severely limiting the mechanical strength of 3D porous scaffolds. Despite numerous studies, Bioglass 45S5 crystallization is not yet fully understood with regard to the mechanisms involved or morphology of the crystal phases forming. Here we show how two cutting-edge imaging techniques, state-of-the-art transmission electron microscopy (TEM) with image correction including energy dispersive X-ray spectroscopy and X-ray nano-computed tomography (nano-CT), allowed us to visualize changes in microstructure from near-nucleation to almost full crystallization in bulk Bioglass 45S5. At early times of heat treatment at 660 °C the formation of phase-separated nano-droplets within the glassy matrix was observed. Later, besides surface crystallization, bulk crystallization of combeite spheres was predominant. The formation of the first combeite spheres, their coarsening with time and finally their merging at near full crystallization were recorded by in situ high-temperature optical microscopy videos. The 3D nature of these spheres was confirmed by nano-CT, while TEM showed that their internal structure was composed of sub-micron grains. X-ray diffraction analysis at early time points showed a much higher crystalline fraction in bulk samples compared to powder samples, highlighting the influence of processing and sample morphology. These results show the importance of using complementary techniques for gaining insight into the crystallization process in the volume. In addition, we show that TEM and nano-CT are suitable characterization techniques to visualize the crystallization even in fast crystallizing systems, such as bioactive glasses.     

Doping manganese into CsPb(Cl/Br)3 quantum dots glasses: Dual-color emission and super thermal stability

CsPbX₃ (X = Cl, Br, I) perovskite quantum dots (QDs) represent bright and tunable photoluminescence, it is regrettable that the air instability and poor water resistant properties prevent their application in optoelectronic devices. At the same time, the toxicity of lead is also a major factor restricting its development. As a consequence, we demonstrate the partial replacement of Pb with Mn through conventional melt-quenching and heat-treatment method preparation of Mn-doped CsPb(Cl/Br)₃ QD glass. Mn-doped CsPb(Cl/Br)₃ QD glass exhibits high luminescent intensity like QDs. It is important that Mn-doped CsPb(Cl/Br)₃ QD glass with Dual-Color maintained the same lattice structure like Mn-doped CsPb(Cl/Br)₃ QDs, and highly homogeneous spectral characteristics of Mn luminescence. The intensity and position of this Mn-related emission are also tunable by altering the experimental parameters, such as the Pb-to-Mn feed ratio, annealing temperature. More importantly, the as-prepared orange Mn-doped CsPb(Cl/Br)₃ QD glass was employed to fabricate white LEDs combined with a commercial Ce³⁺:Y₃Al₅O₁₂ phosphor-in-glass (Ce-PiG) on top of a InGaN blue chip. And the constructed WLEDs generate a warm white with an optimal luminous efficacy (LE) of 67.00 lm/W, a high CRI of 81.4, and a low CCT of 4902 K.     

Enhancement of the radiation resistance of cerium-containing fluorophosphate glasses through codoping with Sb2O3 and Bi2O3

The growing demand for radiation-resistant optical glasses for space and nuclear radiation applications has attracted significant research interest. However, radiation-resistant fluorophosphate glasses have been poorly studied. In this work, we report on the tailoring and performance of radiation-resistant fluorophosphate glasses that contained cerium through codoping with Sb₂O₃ and Bi₂O₃. The physical properties, optical properties, microstructure, and defects of fluorophosphate glasses were investigated using transmittance measurements, absorption measurements, as well as Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electron paramagnetic resonance (EPR) spectroscopy. The results showed that the radiation resistance of all codoped fluorophosphate glasses was better than the undoped cerium-containing fluorophosphate glasses after 10–250 krad(Si) irradiation. Especially in glasses doped with Bi₂O₃, the optical density increment at 385 nm was only 0.1482 after 250 krad(Si) irradiation. The CeO₂ prevented the development of phosphate-related oxygen hole center (POHC) defects, whereas further codoping with Bi₂O₃ suppressed the formation of oxygen hole center (OHC) and POEC defects, reducing the breaking of phosphate chains caused by CeO₂. Bi³⁺ is more likely than Sb³⁺ to change the valence, affecting the transition equilibrium of intrinsic defects and reducing the concentration of defects produced by irradiation. When codoping with Sb₂O₃ and Bi₂O₃, Bi₂O₃ does not enhance radiation resistance owing to the scission effect of Sb₂O₃ on the phosphate chain, which is not conducive to the radiation resistance of glasses. This indicates that the cerium-containing fluorophosphate glasses doped with Bi₂O₃ can effectively suppress the defects caused by irradiation and improve the radiation resistance of the glasses.     

The influence of volume fraction of amorphous phase on corrosion resistance of Mg67Zn 29Ca 4 alloy

The aim of this study was to investigate the structure and corrosion resistance of amorphous, amorphous‐crystalline, and crystalline Mg₆₇Zn₂₉Ca₄ alloy for biodegradable applications. This paper presents a preparation method and results of the structural characterization and corrosion resistance analysis of the material. Samples were prepared in the form of 3 mm diameter rods. The structure of the alloy was examined with the use of X‐ray diffractometry and scanning electron microscopy. The thermal properties of the samples were examined with differential scanning calorimetry (DSC). Results of DSC analysis were used to determine heat treatment temperatures, allowing to obtain different fractures of crystalline phase in the material. Corrosion resistance of heat‐treated samples was investigated by immersion tests and electrochemical measurements performed in the simulated body fluid. The X‐ray diffraction results confirmed that the prepared Mg₆₇Zn₂₉Ca₄ alloy's structure is fully amorphous. After heat treatment, samples with different fractions of amorphous phase in the structure were obtained. Immersion tests of the samples showed that the structure significantly influenced corrosion resistance in examined materials. It should be pointed out, that certain amounts of crystalline phase in amorphous matrix can greatly improve the corrosion resistance of Mg₆₇Zn₂₉Ca₄ alloy.