工艺参数对动态流量控制法挤压弯管应力的影响

采用有限元模拟和实验研究了挤压钛合金弯曲管件。通过实验验证了工件的形状和尺寸精度,并通过有限元模拟分析了工艺参数对挤出过程中变形体的平均压应力分布情况和挤出弯管件的曲率半径的影响规律。结果表明:有限元模拟中,弯管件的曲率半径误差为6.03%,弯管直径误差为3.82%;在靠近定径带处,平均压应力呈非均匀分布;在焊合腔内,靠近细分流孔区域的平均压应力小于靠近粗分流孔区域的平均压应力,平均压应力的大小顺序在通过粗、细分流孔前后相反;在模具结构固定不变时,弯管件的曲率半径随挤压速度的减小而增大,不随挤压温度的变化而变化。     

Influence of Se and Te substitutions at Tl-site of Tl(Ba,Sr)CaCu2O7 superconductor on the AC susceptibility and electrical properties

The Sr and Ba bearing Tl-1212 phase, Tl(Ba,Sr)CaCu₂O₇ is an interesting superconductor. The Sr only bearing TlSr₂CaCu₂O₇ is not easily prepared in the superconducting form. The Ba only bearing TlBa₂CaCu₂O₇ on the other hand does not show improvement in the transition temperature with elemental substitution. In this work the influence of multivalent Se (non-metal) and Te (metalloid) substitutions at the Tl-site of Tl_1-xM_x(Ba,Sr)CaCu₂O₇ (M = Se or Te) superconductors for x = 0–0.6 was studied. The samples were prepared via the conventional solid-state reaction method. XRD patterns showed a single Tl-1212 phase for x = 0 and 0.1 Se substituted samples. The critical current density at the peak temperature, T_p of the imaginary (χ”) part of the AC susceptibility (χ = χ’ +χ”), J_c-inter(T_p) for all samples was between 15 and 21 A cm⁻². The highest superconducting transition temperature was shown by the x = 0.3 Se-substituted sample (T_c-onset = 104 K, T_c-zero = 89 K, T_cχ’ = 104 K and T_p = 80 K). Te suppressed the superconductivity of Tl-1212 phase. The order of highest transition temperatures are as follows: Tl_1-xTe_x(Ba,Sr)CaCu₂O₇<Tl(Ba,Sr)CaCu₂O₇<Tl_1-xSe_x(Ba,Sr)CaCu₂O₇. This work showed that Se was better than Te in improving the transition temperature and flux pinning of the Tl-1212 phase. The roles of ionic radius of Se and Te on the superconductivity of Tl(Ba,Sr)CaCu₂O₇ are discussed in this paper.     

自重湿陷性黄土地基预钻孔浸水处理的可靠度设计方法

为解决传统预浸水法存在的浸水时间长、浸水处理范围难以确定等不足,基于土体中水分运移规律,依据可靠度理论、极限状态设计方法及复合 Poisson 过程原理,提出一种消除黄土湿陷性的处理浸水方法——预钻孔浸水法。给出了利用预钻孔浸水法对自重湿陷性黄土地基进行浸水时,水平向及竖直向浸水影响范围的确定模型;在此基础上结合达西定律给出了浸水孔设计参数如孔深、孔间距及浸水孔个数的确定方法。结合铜川某工程,设计进行了现场预钻孔浸水试验,对该方法的合理性进行了验证,并通过现场钻探、现场勘探、室内湿陷性试验等方法对该方法的处理效果进行了评价。该浸水方法具有浸水时间短、浸水影响范围可根据浸水孔布设进行控制等优点,且浸水处理效果良好,完全符合施工要求。     

常压干燥合成水玻璃基SiO_2气凝胶

以水玻璃和双氧水为原料一步合成二氧化硅湿凝胶,经老化、溶剂置换及三甲基氯硅烷修饰后,并于常压干燥后获得二氧化硅气凝胶。样品经低温N_2吸附-脱附、红外光谱和扫描电镜测试表明所得二氧化硅气凝胶具有三维多孔结构,且其比表面积可达482 m~2·g~(-1)、平均孔径为24.9nm及表观密度为0.12g·cm~(-3)。     

采煤工作面煤层注水参数试验研究

通过在6198采煤工作面现场施工煤层注水钻孔采取煤样,实验室试验注水钻孔水压力分布、煤样含水率变化,得到了工作面煤层注水影响半径等技术参数,为采煤工作面煤层注水提供了一定的参考依据。     

滚齿工艺对齿根粗糙度的影响

针对国内外风电和工业齿轮箱轻量化的设计趋势,较低的安全系数对齿轮齿根弯曲强度提出了更为严格的要求。研究表明,在材料技术和齿形设计难以再优化的情况下,滚齿加工的粗糙度,尤其是齿根部位的粗糙度对齿轮弯曲强度的影响尤为敏感。针对滚齿工艺过程,从滚齿加工参数、刀具前刀面粗糙度和刀具刃口圆角三方面进行分析,验证其对齿根粗糙度的影响。     

Effect of ionic radius on colossal permittivity properties of (A,Ta) co-doped TiO2 (A= alkaline-earth ions) ceramics

(A, B) co-doped TiO₂ ceramics attract great interests due to the excellent dielectric properties. In this work, the (A, Ta) co-doped TiO₂ ceramics were prepared by a solid state reaction process. The effect of the acceptors ionic radius on the structure and properties of TiO₂ ceramics was investigated. According to XRD analysis, the main phase is rutile TiO₂ for all samples. Due to the larger ionic radius, it is hard to replace Ti site in TiO₆ octahedron. As a result, the content of the secondary phase increased with increasing ionic radius. The dielectric properties were significantly enhanced by co-doping of alkaline-earth ions and tantalum ions, and the best dielectric constant obtained at 3% (Sr, Ta) co-doped compositions, where ε’ = 2.1 × 10⁵, tanδ = 0.21. Meanwhile, the XPS analysis suggested that the concentration of the defect dipoles exhibit a maximum in Sr-doped TiO₂ ceramics. The larger ionic radius of the acceptors leads to the more stability of the defect structure. However, for Ba ions, the replacement concentration decreased due to the excessive ionic radius, which in turn reduces the defect concentration. This work is meaningful for the further investigations on TiO₂-based colossal permittivity materials.     

Elemental substitution at Tl-site of TlSr2CaCu2O7 superconductor: A review

This review is on the effects of elemental substitutions at the Tl-site of TlSr₂CaCu₂O₇ (Tl-1212) superconductor. The objective of this paper was to determine the elements that enhance or suppress the superconducting transition temperature, T_c of (Tl_1-xM_x)Sr₂CaCu₂O₇ phase. The elements included in this review were M = Pb, Bi, Cr, V, Re, Zr, In, Er, Gd, Na, K, Rb and Se. The relations between transition temperature and the ionic radius, coordination number, valence state and optimization of the hole concentration of the selected elements were studied. The preparation methods, sintering temperature, Tl-1212 phase and structural stability were also discussed. All alkali metals (K, Na and Rb) suppressed the transition temperature of the Tl-1212 phase. The transition temperature generally decreased linearly with ionic radius except for Cr which showed the highest T_c although its ionic radius is smaller.     

Macromolecular motions and hydrodynamic radius variation in dilute solutions under shear action

Understanding the dynamics of single polymer chains and rheological mechanism in dilute polymer solutions under shear stress is essential for fields such as the petroleum and food industries, biomedical materials and drug delivery. Here we present an experimental method for measuring the viscosity of polymer solutions and studying the variation of single polymer chain conformation and the mechanism of molecular motions according to the relationship between the intrinsic viscosity, [η], and the shear rate. Of striking interest is that we find that [η] changing with the shear rate presents three stages which may explain the nature of the viscoelastic performance of polymer solutions and the isolated molecular motions. The significance of these results is the finding of the polymer chain deformation to match the pore throat which has enormous potential implications in drug delivery, genetics and biomedicine © 2014 Society of Chemical Industry.     

斜沟煤矿18205工作面CO2致裂增透最优钻孔布置参数研究

为了得到斜沟煤矿18205工作面CO2致裂爆破钻孔最优布置参数,提高煤层瓦斯透气性系数,依据物理爆破原理,推导出了二氧化碳致裂器爆破时产生裂隙圈半径的计算公式;并通过FLAC^3D数值模拟软件进行模拟,得出:爆破孔间距为7 m、爆破器间距为5 m时,液态CO2致裂爆破可实现最佳的增透效果,当爆破孔间距越大时,透气性系数提高幅度越大,煤层增透效果越显著,抽采效率越高。