IF板与08Al板的成形性能研究

通过模拟成形性试验，对新型超深冲用IF钢板和传统冲压用08Al钢板的冲压成形性能进行了研究．结果表明：IF板的拉深性能、扩孔性能、胀形性能以及“拉深-胀形”复合性能等均优于08Al板，其中，扩孔性能和平面各向异性的改善最为显著；各项试验中，IF板的成形力普遍小于08Al板。     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

关于粉体成球机盘体几何形状的研究

通过对粉体小球在粉体成球机盘底上运动轨线的研究,利用Euler定理,结合其参数特点,得到了不同几何形状的盘底在成球过程中对粉体小球运动的影响,球面盘底较平面盘底更有利于成球的结论。     

翻领成型器领口曲线的程序计算展开法

根据翻领成型器领口曲线的数学模型，介绍一种利用计算器复杂公式存贮的特殊功能，预编程序计算相关参数。然后画领口曲线展开图的方法。     

工业产品的艺术造型与技术美学

本文从技术美学的角度，广义的介绍了工业产品艺术造型的基本方法，着重从美学原则和色彩设计两方面论述产品造型设计的手法，以及技术美学在产品造型设计中的基本应用。     

Effect of Forming Pressure on the Internal Structure of Alumina Green Bodies Examined with Immersion Liquid Technique

Green bodies prepared by compaction of alumina granules were made transparent by an immersion liquid technique, and the internal structure was characterized with an optical microscope to study the effect of forming pressure on the internal structure. Clear images obtained by the technique provide more detailed information than other existing methods for structures ranging from one to tens of micrometers. Intergranular pores were present between unfractured granules. Their sizes and concentration tended to decrease with increasing forming pressure. However, pores were clearly present even in the green body prepared at 600 MPa. A rod- and needlelike feature was also found and was concluded to correspond to a high-density region. The significance of large pores and high-density regions on processing as well as the details of the technique is discussed.     

圆锥形零件冲压变形与成形载荷的分析

由于悬空侧壁部分的变形状态是圆锥形零件成形的关键，而径向拉应力是实现悬空部分成形的必要条件，同时也是该部分冲压成形成败的关键为此，经力学分析得出了侧壁部分径向拉应力的解析式和造成圆锥形零件破裂的最大径向拉应力的计算式。同时分析了圆锥形零件的成形载荷。     

楔块体积成形模的应用

本文介绍了几种典型楔块体积成形模的工作原理,以及它们在模具工业上的应用。     

Spray forming technology for military applications

Over the past five years, the Annapolis Detachment, Carderock Division, Naval Surface Warfare Center (formerly David Taylor Research Center) has established a state- of- the- art spray forming facility for the study and exploitation of this near net shape manufacturing process. Spray forming is a single step gas atomization/deposition process which yields ferrous and nonferrous, near final shape, near fully dense preforms that has proven to be a viable and cost effective alternative to conventional metalworking technology for the production of material preforms with properties surpassing those of their cast and wrought counterparts. Current programs at Carderock Divison Naval Surface Warfare Center are aimed at optimization of the process, certification of the spray formed products and industrialization of the technology.