Constitutive model for gas hydrate-bearing soils considering different types of hydrate morphology and prediction of strength-band

The present study proposes a new elasto-plastic constitutive model that considers different types of hydrates in pore spaces. Many triaxial compression tests on both methane hydrate-bearing soils and carbon dioxide hydrate-bearing soils have been carried out over the last few decades. It has been revealed that methane hydrate-bearing soils and carbon dioxide hydrate-bearing soils have different strength and dilatancy properties even though they have the same hydrate contents. The reason for this might be due to the different types of hydrate morphology. In this study, therefore, the effect of the hydrate morphology on the mechanical response of gas-hydrate-bearing sediments is investigated through a model analysis by taking into account the different hardening rules corresponding to each type of hydrate morphology. In order to evaluate the capability of the proposed model, it is applied to the results of past triaxial compression tests on both methane hydrate-containing and carbon dioxide hydrate-containing sand specimens. The model is found to successfully reproduce the different stress–strain relations and dilatancy behaviors, by only giving consideration to the different morphology distributions and not changing the fitting parameters. The model is then used to predict a possible range in which the maximum deviator stress can move for various hydrate morphology ratios; the range is defined as the strength-band. The predicted curve of the maximum deviator stress obtained by the constitutive model matches the empirical equations obtained from past experiments. It supports the fact that the hydrate morphology ratio changes with the total hydrate saturation. These findings will contribute to a better understanding of the relation between the microscopic structures and macro-mechanical behaviors of gas-hydrate-bearing sediments.     

非常规气藏储层改造体积评价方法研究

为精确描述非常规气藏压裂后的复杂流动特征及定量评价储层改造体积（SRV），利用自主研发的缝网重构算法“破裂树生长法”建立压后缝网模型，并以此为基础提出了使用拟稳态流动时特定的压力等值线来确定SRV范围的定量评价方法，最后以长宁201井区为例进行了矿场实例分析。该方法根据微地震监测点的位置，重构出微裂缝网的连通关系。在复杂微裂缝网的基础上建立离散裂缝地质模型并进行生产数值模拟，根据数值模拟结果的压力分布精确划定SRV的范围。利用该方法计算出长宁201井区的SRV体积为0.052 1 km3，以该缝网模型的数值模拟产量预测结果符合实际生产规律，方法实用性较好。     

煤峪口矿81010工作面煤层底板裂隙发育特征及防治

针对煤炭开采过程中出现的突水事故,采用RFPA数值模拟软件建立采动模型,对底板裂隙破断过程和声发射进行模拟,研究煤层底板采动裂隙扩展突水通道,结果表明:离断层越近,断层内水压导升高度越高,断层出现活化,裂隙扩展发育,最终贯通形成导水通道,在进行注浆改造后,单个钻孔的最大涌水量为8 m³/h,说明注浆加固防治水效果较好,能确保工作面的安全回采。     

Quantification of Dendritic Spines Remodeling under Physiological Stimuli and in Pathological Conditions

Numerous brain diseases are associated with abnormalities in morphology and density of dendritic spines, small membranous protrusions whose structural geometry correlates with the strength of synaptic connections. Thus, the quantitative analysis of dendritic spines remodeling in microscopic images is one of the key elements towards understanding mechanisms of structural neuronal plasticity and bases of brain pathology. In the following article, we review experimental approaches designed to assess quantitative features of dendritic spines under physiological stimuli and in pathological conditions. We compare various methodological pipelines of biological models, sample preparation, data analysis, image acquisition, sample size, and statistical analysis. The methodology and results of relevant experiments are systematically summarized in a tabular form. In particular, we focus on quantitative data regarding the number of animals, cells, dendritic spines, types of studied parameters, size of observed changes, and their statistical significance.     

Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

Immiscible PHB/PBS and PHB/PBSA blends: morphology,phase composition and modelling of elastic modulus

This paper reports the thermal, morphological and mechanical properties of environmentally friendly poly(3-hydroxybutyrate) (PHB)/poly(butylene succinate) (PBS) and PHB/poly[(butylene succinate)-co-(butylene adipate)] (PBSA) blends, prepared by melt mixing. The blends are known to be immiscible, as also confirmed by the thermodynamic analysis here presented. A detailed quantification of the crystalline and amorphous fractions was performed, in order to interpret the mechanical properties of the blends. As expected, the ductility increased with increasing PBS or PBSA amount, but in parallel the decrease in the elastic modulus appeared limited. Surprisingly, the elastic modulus was found properly described by the rule of mixtures in the whole composition range, thus attesting mechanical compatibility between the two blend components. This unusual behavior has been explained as due to co-continuous morphology, present in a wide composition range, but also at the same time as the result of shrinkage occurring during sequential crystallization of the two components, which can lead to physical adhesion between matrix and dispersed phase. For the first time, the elastic moduli of the crystalline and mobile amorphous fractions of PBS and PBSA and of the mobile amorphous fraction of PHB at ambient temperature have been estimated through a mechanical modelling approach. © 2021 The Authors. Polymer International published by John Wiley & Sons Ltd on behalf of Society of Industrial Chemistry.     

石墨烯纳米制冷剂核态池沸腾换热的实验研究

为分析单层石墨烯纳米片对核态池沸腾换热的影响机理，对基液为R141b、分散相为单层石墨烯纳米片的纳米制冷剂的核态池沸腾换热特征进行了测定，采用Hot Disk热物性分析仪和铂金板法分别测定了石墨烯纳米制冷剂的热导率和表面张力，采用接触角测量仪和扫描电子显微镜（SEM）观测了沸腾后加热表面的润湿性和形貌特征。实验中，单层石墨烯纳米片的质量百分含量（ω）为0.02%~0.50%，实验压力为一个标准大气压，热流密度为20~200 kW/m2。实验结果表明：单层石墨烯纳米片的加入，使制冷剂R141b的核态池沸腾换热得到强化；当ω=0.2%时，换热系数提高比例出现峰值，为57.7%。伴随ω的增加，石墨烯纳米制冷剂的热导率增大、表面张力减小，沸腾表面润湿性增强且微腔数先增后减，综合作用的结果导致存在一个最佳的单层石墨烯纳米片浓度（即ω=0.2%）使换热系数最高。     

丙烯酸装置循环气压缩机叶片损伤分析与修复

某石化公司丙烯酸装置循环气压缩机在运行过程中,一级叶片突然发生断裂,导致机组停机。采用宏观检查、扫描电子显微镜、能谱分析等方法对断裂叶片进行检验和检测,将断裂叶片的材质、裂纹及断口特征检测结果与疲劳断裂特征和机组运行状况进行对比,确定压缩机叶片的断裂系其达到疲劳寿命所致,提出采用激光熔覆方法对压缩机叶片进行修复,介绍了修复工艺操作程序要点,可为同类故事的处理提供参考。     

矿用直线振动筛结构故障分析

针对煤矿选煤厂直线振动筛工作过程中出现的结构故障问题,采用有限元仿真与现场测试结合的方法对振动筛出现故障的原因进行了分析研究。介绍了振动筛的主要结构及常见故障,并以某矿选煤厂发生大梁断裂的振动筛为例,对该振动筛进行三维建模和有限元模态分析,分析结果表明:随着模态阶次的增加,振型的变化逐渐由移动转为结构本身的扭曲变形。在该振动筛空载工作状态下,选用本质安全型便携式测振记录仪进行振动测试并处理测试信号,得到该振动筛的工作频率。结合模态分析结果和实际测试结果,判断出空载时频繁运行振动筛是造成其大梁断裂的主要原因。根据故障原因给出维护建议:应当尽量避免振动筛在空载或物料较少的状态下长时间运行;在振动筛投入使用前,应预先了解振动筛的工作状态及可能存在的薄弱环节,尽可能避免结构故障,保证振动筛可靠运行。