一种基于空间到达角的卫星电子侦察信号分选方法

在建立简化的卫星电子侦察空间模型的基础上，提出了一种利用空间到达角分选卫星电子侦察信号的新方法。通过仿真实验验证了这种方法的可行性。该方法可用于密集信号的预处理。     

T8钢－聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性、磨料磨损特性及对土壤的减粘降阻性能与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％～２２．２７％     

A versatile data acquisition system for time resolved X-ray scattering using gas proportional detectors with delay line readout

A data acquisition system for time resolved X-ray scattering experiments using linear, quadrant or area gas proportional detectors with delay line readout based on commercially available hardware (National Instruments) is described. The system can easily be configured for recording data from point detectors (e.g. photomultipliers and photodiodes) and/or ancillary data only. Applications involving measurements with two different types of time to digital converters illustrate the features and performances of the system.     

Pheromone Disruption of Argentine Ant Trail Integrity

Disruption of Argentine ant trail following and reduced ability to forage (measured by bait location success) was achieved after presentation of an oversupply of trail pheromone, (Z)-9-hexadecenal. Experiments tested single pheromone point sources and dispersion of a formulation in small field plots. Ant walking behavior was recorded and digitized by using video tracking, before and after presentation of trail pheromone. Ants showed changes in three parameters within seconds of treatment: (1) Ants on trails normally showed a unimodal frequency distribution of walking track angles, but this pattern disappeared after presentation of the trail pheromone; (2) ants showed initial high trail integrity on a range of untreated substrates from painted walls to wooden or concrete floors, but this was significantly reduced following presentation of a point source of pheromone; (3) the number of ants in the pheromone-treated area increased over time, as recruitment apparently exceeded departures. To test trail disruption in small outdoor plots, the trail pheromone was formulated with carnuba wax-coated quartz laboratory sand (1 g quartz sand/0.2 g wax/1 mg pheromone). The pheromone formulation, with a half-life of 30 h, was applied by rotary spreader at four rates (0, 2.5, 7.5, and 25 mg pheromone/m²) to 1- and 4-m² plots in Volcanoes National Park, Hawaii. Ant counts at bait cards in treated plots were significantly reduced compared to controls on the day of treatment, and there was a significant reduction in ant foraging for 2 days. These results show that trail pheromone disruption of Argentine ants is possible, but a much more durable formulation is needed before nest-level impacts can be expected. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

基于Lab VIEW的小型汽油机磁电机点火提前角的测量

本文介绍了磁电机点火系统的点火提前角测量原理。对点火系统的点火信号和触发信号进行采集、调理，再用单片机进行处理，最后用LabVIEW进行点火提前角数据存储和显示。     

Effects of Spatial Characteristics on Smart Antenna System with Uniform Linear Antenna Array

1IntroductionCurrently,smart antenna technology can greatly en-hance system performance and i mprove the system ca-pacity so that it has been considered as a keytechnologyinthe third generation wireless communicationsystems .The researches on channel model , beamforming algo-rithms and receive algorithms have been widely carriedout and a great many of proposition have beensubmittedtothe 3th Generation Project Partner (3GPP) . Fromthe viewpoint of link-level and system-level research,many asp…     

The Influence of Surfactant on the Surface Characterization of Celestite in Spherical Oil Agglomeration

This study investigates the relationship between the critical surface tension of wetting of celestite and agglomeration recovery as well as the zeta potential in dependence of pH and amount of collector (Na‐Oleate). For this purpose, effects of pH and collector amount on the agglomeration recovery are investigated and zeta potential measurements and Fourier Transform Infrared Spectrophotometer (FTIR) analyses are carried out to determine the adsorption type of Na‐Oleate on celestite surface. The sessile drop technique is used for the measurement of contact angle and determination of the critical surface tension of wetting (Y_C) of celestite. The maximum agglomeration recovery is obtained at pH 7. The critical surface tension of wetting of celestite is very close to the surface tension of kerosene, which is 25.95 mN/m. Furthermore, at the optimum Na‐Oleate amount of 10 kg/ton, the critical surface tension of wetting of celestite is approximately equal to the surface tension of kerosene.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．