Corrosion of structural constituents of 2017 aluminium alloy in acidic solutions containing inhibitors

The objective of this study is to establish the corrosion behaviour of the most important structural constituents of the aluminium alloy 2017 in orthophosphoric acid solutions containing heteropolyoxomolybdate, tungstate and vanadate. These are potential candidates for replacing toxic hexavalent chromium species in stripping solution for anodic coatings. The corrosion rate of the alloy is estimated with linear polarisation method. It decreases from 0.58 mA cm⁻² in uninhibited solution to 0.10 mA cm⁻² in a solution containing heteropolyoxomolybdate species. Microscopic studies reveal that heteropolyoxomolybdate species inhibit corrosion of the matrix and intermetallic Al₁₅(Fe,Mn)₃(Si,Cu)₂ but not Mg₂Si. Intermetallic Al₂Cu remains not corroded. Heteropolyoxotungstate species virtually do not inhibit the corrosion of the alloy. The solution containing vanadium species is not stable with time and the corrosion rate is not determined. Nevertheless, corrosion of the matrix is inhibited, but intermetallics Al₁₅(Fe,Mn)₃(Si,Cu)₂ together with Mg₂Si are dissolved. X-ray photoelectron spectroscopy is used for examination of a corrosion product precipitated on the surface.     

Measurement of residual stresses in dissimilar friction stir-welded aluminium and copper plates using the contour method

The longitudinal residual stresses in the friction stir-welded plates of 5A06 aluminium and pure copper were determined using the contour method. The results revealed the presence of high tensile and compressive residual stresses on the aluminium and copper sides, respectively. The residual stresses were detected on the weld zone as well as the thermo-mechanically affected zone (TMAZ) of the aluminium plate. In contrast, the compressive residual stresses in the copper plate had a much narrower width along the weld line. Peak tensile stresses up to 240?MPa were found in the TMAZ of the aluminium plate.     

Investigation of the influence of iron-containing abrasives on the corrosion behaviour of the aluminium alloy AlSi1.2Mg0.4

The corrosion resistance of aluminium surfaces is closely linked to the surface state after a grinding process. For years, iron-containing abrasive materials were suspected to lead to increased corrosion susceptibility after processing of aluminium surfaces. To prove a possible correlation between the iron content of an abrasive and the corrosion behaviour of aluminium components, scientific investigations and experimentally practical corrosion tests are necessary. For the current investigation, specimens of a technical Al-Si alloy from the same batch were used. The test specimens were mechanically ground with various resin-bonded model abrasives containing different iron contents. The performed corrosion tests did not reveal a negative influence of the different iron-containing abrasives on the corrosion behaviour of the Al–Si alloy. However, the most sensitive measuring method (electrochemical noise) showed differences in the surface activity depending on the type of abrasive.     

Process and joint quality of ultrasonic vibration enhanced friction stir lap welding

In order to improve the process effectiveness and joint quality, ultrasonic vibrations were integrated with friction stir lap welding. Effect of ultrasonic exertion on the process and joint quality of AA 6061-T6 were investigated. Upon ultrasonic exertion, joints owned larger effective lap width, shorter hooks and improved strength. Weld fracture mode changed from a ductile–brittle mixed mode to a more ductile mode while the fracture path shifted from lap interface to beyond the stir zone. Material flow and interface defects were characterised using lap welded dissimilar aluminium alloy joints. Ultrasonic vibration improved the material flow and reduced the interfacial defects. Variations in failure load of joints were found in accordance with the variations in material flow and interfacial defects.     

Extraction equilibrium conditions of beryllium and aluminium from a beryl ore for optimal industrial beryllium compound production

This study examines the extraction of beryllium and aluminium from a Nigerian beryl ore using Cyanex®272 in kerosene from an aqueous sulphate pregnant solution. Parameters such as extractant concentration and equilibrium pH that dictates the extraction yield were studied. Under the following conditions: temperature 27?±?2°C, phase ratio 1?1, about 45.50 and 46.76% of beryllium and aluminium were extracted by 0.15?mol?L^?1 Cyanex®272 concentration within 30?min. However, the extraction yield of beryllium and aluminium was increased to 91.68% and 97.89% at equilibrium pH of 3 and 4, respectively, for beryllium and aluminium at 27?±?2°C. A 0.05?mol?L^?1 H₂SO₄ solution was found to be adequate for the stripping of about 99.00% Be and 95.40% Al from the loaded organic phase. The pure solutions containing metal ions were accordingly beneficiated to obtain beryllium and aluminium compounds of industrial values.     

A new cladding technology to bond aluminium on magnesium

ABSTRACT

An in situ hot press bonding technology has been developed to clad aluminium on magnesium. Followed by regular hot rolling, magnesium sheets, covered by ductile and corrosion-resistant aluminium without detectable oxides in the interface, are produced. The new technology requires no welding, vacuum, protective atmosphere or barrier layer, and it makes good interfacial strength and rollability. Aluminium–magnesium intermetallic phases are formed along the clad–core interface at elevated temperatures. They are not detrimental under compression but may cause clad-core delamination in tensile strain. However, the tensile failure is more dependent on the formability of magnesium core than on the strength of interface.     

Corrosion behaviour and mechanism of 6082 aluminium alloy in NaCl and Na2SO4 etchants

The corrosion behaviour of 6082 aluminium alloy was studied by measuring the electrochemical impedance spectra and electrode polarization curves. After the electrochemical tests, a microstructural analysis of the samples was conducted by using optical microscopy and electron scanning microscopy techniques to determine the corrosion mechanism. The results show that the Nyquist plot of the electrochemical impedance data in the NaCl solution consists of high- and low-frequency capacitive impedance loops. When ions are added to the NaCl etchant, the Nyquist plots of the electrochemical impedance data are composed of two different curves: a high-frequency capacitive impedance loop and a low-frequency inductive impedance loop. The corrosion current density increases with increasing concentration, and as a result, the corrosion resistance of the aluminium alloy decreases. The microstructures of 6082 aluminium alloy consist of Mg₂Si secondary particles in a large α-Al matrix. Pitting corrosion initially occurs at the boundary between the matrix and secondary particles because the electrode potentials of the matrix and secondary particles are different. Then, corrosion paths develop along the network-like grain boundaries, and finally, massive network-like corrosion occurs throughout the entire alloy.     

Corrosion behaviour of AA2024 aluminium alloy in different tempers in NaCl solution and with the CeCl3 corrosion inhibitor

The paper analyses the corrosion behaviour of naturally and artificially aged AA2024 alloy in NaCl solution and in the presence of an environment-friendly corrosion inhibitor, CeCl₃. On the basis of the values of polarisation resistance and corrosion current density, the corrosion resistance of the protective inhibitor film is established as well as the general corrosion resistance of this aluminium alloy. Resistance to pit formation is determined based on the difference in pitting and corrosion potentials while resistance to pit growth is determined based on the amount of charge consumed during pit growth. A scanning electron microscope is used to examine the morphology of the pits formed during the pitting corrosion testing, as well as to determine the cerium content on intermetallic particles and the matrix AA2024 alloy. The corrosion behaviour of AA2024 alloy is investigated after different test periods in NaCl solution and in the same solution with the CeCl₃ inhibitor. The corrosion resistance of both tempers of AA2024 alloy is more than one order of magnitude higher in the presence of CeCl₃. An explanation of the observed differences in the corrosion behaviour of the naturally and artificially aged AA2024 alloy is proposed. Different corrosion behaviour of the alloy after different test periods is also explained.     

A waste heat recovery system development and analysis using ORC for the energy efficiency improvement in aluminium electrolysis cells

The present work investigates an active waste heat recovery system for the side walls of the aluminium electrolysis cells, enabling utilization of the extracted heat in power generation. This will potentially lead to energy efficiency improvement in the primary aluminium production industry and an enhanced aluminium production rate. An experimentally validated loop thermosyphon heat pipe model was used for heat extraction from the cell side wall. Boosting system thermal efficiency through waste heat recovery, by means of a heat utilization system, and increasing the level of control, as well as thermal equilibrium, stand as the main addressed objectives of the current study, which consequently result in an increased aluminium production rate. An organic Rankine cycle is incorporated into the system, and its performance is evaluated, taking into consideration the operating situations in terms of available temperature and thermal power range.     

铝金属化纸制备工艺的专利技术发展

通过对铝金属化纸领域专利技术的收集、分析、标引,介绍了铝金属化纸的制备方法及种类,包括铝粉涂布、铝箔纸以及可降解回收的真空镀铝纸等;并对其专利申请量、区域分布以及渡铝技术进行了分析,同时对各技术的发展历程和改进情况进行了梳理归纳。