Energetics of Plastic Deformation of Metastable Austenitic Stainless Steel

The change in the internal energy during uniaxial tensile deformation of austenitic stainless steels EN 1.4301 (AISI 304) and EN 1.4318 (AISI 301LN) was determined by measuring the extent of γ→α'‐martensite transformation and the temperature increase of the samples. From the results the fraction of the stored energy of cold work and the free energy change related to the strain‐induced γ→α'‐martensite transformation were determined. The fraction of stored energy varied around 0.4. With the metastable steel grades the free energy change related to the γ→α'‐martensite transformation was found to vary between ‐98 MJ/m³ and ‐206 MJ/m³ depending on the austenite stability of the steel. Furthermore, the magnitude of the mechanical driving force was estimated by comparing the results with the free energy change of thermally induced transformation.     

低碳马氏体强化工艺的应用

低碳钢及低碳合金钢的淬火马氏体具有良好的综合力学性能。本文简述了08F，Q235-A，20，20Cr，高强度螺栓用钢ML15，25CrMnSiA和ZG28SMnVCu钢的低碳马氏体强化工艺及其应用。     

Characterization of blasted austenitic stainless steel and its corrosion resistance

It is known that the corrosion resistance of stainless steel is deteriorated by blasting, but the reason for this deterioration is not clear. A blasted austenitic stainless steel plate (JIS-SUS304) has been characterized with comparison to the scraped and non-blasted specimens. The surface roughness of the blasted specimen is larger than that of materials finished with #180 paper. A martensite phase is formed in the surface layer of both blasted and scraped specimens. Compressive residual stress is generated in the blasted specimen and the maximum residual stress is formed at 50–100 μm from the surface. The corrosion potentials of the blasted specimen and subsequently solution treated specimen are lower than that of the non-blasted specimen. The passivation current densities of the blasted specimens are higher those of the non-blasted specimen. The blasted specimen and the subsequently solution treated specimen exhibit rust in 5% sodium chloride (NaCl) solution, while the non-blasted specimen and ground specimen do not rust in the solution. It is concluded that the deterioration of corrosion resistance of austenitic stainless steel through blasting is caused by the roughed morphology of the surface.     

9SiCr钢中的筐篮编结状马氏体及其性能

将9SiCr钢的粒状原始组织改变为片状,再经830℃淬火后,其马氏体形态为筐篮编结状。而传统工艺所获得的马氏体形态为针状.这种筐篮编结状马氏体是9SiCr钢中一种崭新的组织形态,其精细结构为平行成束的板条。亚结构为高密度缠结位错.它有良好的综合机械性能,强韧性高,耐磨性高。     

Cu-Al-Be形状记忆合金的应力腐蚀性能

用恒载荷法和慢应变速率法及SEM研究了Cu-Al-Be形 状记忆合金在甘油、海水和氨介质中的应力腐蚀性能.结果表明，Cu-Al-Be合金具有良 好的抗海水应力腐蚀性能和较低的氨介质应力腐蚀倾向.单相马氏体有较 好的耐海水腐蚀能力，可减少腐蚀引起的裂纹源；外应力下马氏体的孪晶变形和变体间的界 面迁移，则有利于松弛应力集中，阻碍和延缓腐蚀裂纹源的扩展，从而提高Cu-Al-Be合金的 应力腐蚀能力.     

Corrosion behavior of tempered dual-phase steel embedded in concrete

Dual-phase(DP) steels with different martensite contents were obtained by appropriate heat treatment of an SAE1010 structural carbon steel,which was cheap and widely used in the construction industry. The corrosion behavior of DP steels in con-crete was investigated under various tempering conditions. Intercritical annealing heat treatment was applied to the reinforcing steel to obtain DP steels with different contents of martensite. These DP steels were tempered at 200,300,and 400°C for 45 min and then coo...     

Stress-strain partitioning analysis of constituent phases in dual phase steel based on the modified law of mixture

A more accurate estimation of stress-strain relationships for martensite and ferrite was developed, and the modified law of mixture was used to investigate the stress-strain partitioning of constituent phases in dual phase (DP) steels with two different martensite volume fractions. The results show that there exist great differences in the stress-strain contribution of martensite and ferrite to DP steel. The stress-strain partitioning coefficient is not constant in the whole strain range, but decreases with...     

煤仓漏斗的焊接工艺

针对Q235-B钢板制成的原煤仓漏斗锈蚀、磨损严重的问题,更换采用了内层为4Cr13马氏体不锈钢,外层为Q235-B钢板的双层结构漏斗,并通过焊接工艺试验为煤仓漏斗的制造工艺确定了正确的焊材和焊接方法,取得了良好的效果。     

Cu-Al-Mn-Zn-Zr记忆合金的显微组织与力学行为

利用金相显微镜、透射电镜、扫描电镜观察和力学性能测试等手段研究了Cu—18．4A1—8．7Mn—3．4Zn—0．1Zr(摩尔分数，％)记亿合金(多晶)在不同温度与组织下变形时的力学行为。实验合金在不同温度下变形时延伸率不同，变形温度(Td)在Ms与Af之间时的延伸率小于变形温度(Td)高于Af时的延伸率。对实验合金施加应力时，最初的变形主要来自应力诱发马氏体，继而发生马氏体变体择优合并，二者对合金的变形都有贡献；变形量更大时，变体界面共格性被破坏，部分马氏体丧失热弹性。少量α相的析出不影响记忆效应，可使延伸率得以提高。     

Cu-Zn-Al形状记忆合金直接淬火和分级淬火后马氏体稳定性的研究SCIEI

用透射电镜,X射线衍射仪和电阻法研究了Cu-14.84wt-％Zn-7.75wt-％Al形状记忆合金在直接淬火和分级淬火后马氏体的稳定性。试验结果表明,直接淬火和分级淬火(150℃,2min)后于室温时效约3h的马氏体均为M18R结构,但刚直接淬火后马氏体并不稳定,其某些衍射峰位置和电阻率均随室温时效而变化;而分级淬火(150℃,2min)后马氏体是稳定的,其所有衍射峰位置和电阻率几乎不随室温时效而变化。上述结果可用“马氏体再有序化机制”解释。