特种工程胎硫化外胎质量缺陷原因分析以及解决措施

我公司使用的硫化机采用氮气定型,二次水硫化的工艺。由于特种工程胎胎体偏厚且大,成型机都比较大,生产过程中的帘布筒、钢丝、胎侧等部件都比较重且大。成型胎面使用胎面缠绕机缠绕,所以整个生产过程难度较大。特种工程胎硫化外胎的主要质量问题有:胎面皮泡、胎侧缺胶、胎侧泡、胎肩侧皮泡、子口内侧露线、子口缺胶、胎肚内缺(窝气)、胎肚露线、胎肚皮泡、胎肚串泡、子口支边、胎冠支边、子口鼓包、外胎花缺等。通过对特种工程胎硫化外胎质量缺陷原因分析,找到相应的解决措施,从而减少硫化外胎质量缺陷。     

Mechanical properties,corrosion resistance,and rubber pad forming of cold differential speed-rolled pure titanium for bipolar plates of proton-exchange membrane fuel cells

Due to problems such as pores on surface-treated coatings, the corrosion resistance of pure titanium bipolar plates for proton-exchange membrane fuel cells can be further improved by increasing the corrosion resistance of pure titanium by using differential speed-rolling (DSR); however, these materials have not yet reached the standard requirements of bipolar plates (corrosion current density i_corr＜10³ nA·cm^?2). In this work, the corrosion resistance of pure titanium was improved by optimizing the DSR process while the strength was maintained. The best corrosion resistance of the DSR pure titanium was achieved when the roller speed ratio was 2, while i_corr was 429 nA·cm^?2 in a solution of 0.5 M H₂SO₄ and 2 mg/L HF at room temperature. The formability of the DSR pure titanium for bipolar plates was verified. The optimal holding pressure range was 6.8–7.0 kN.     

影响多步脱氢酶CrtI功能的关键结构特征探索

在生物体内存在可催化多步连续反应的通用酶，对生物代谢过程具有重要作用。八氢番茄红素脱氢酶（CrtI）作为典型代表,可以催化多步连续脱氢反应,生成番茄红素等具有重要价值的产物。本文以酿酒酵母为底盘研究CrtI的催化功能特征。首先通过组合设计与筛选番茄红素合成路径中的三种外源酶CrtE、CrtB和CrtI，发现CrtI是主要的限制因素，且三孢布拉氏霉菌来源的CrtI(BtCrtI)表现出优异的催化功能。通过生物信息学与蛋白结构分析发现BtCrtI的S311残基是连接和稳定活性中心结构的关键。随后通过分析该位点的饱和突变结果，揭示了该位点的氨基酸残基类型对活性中心结构和功能的显著作用，为酶的设计和改造提供了新的思路。同时发现CrtI的活性差异未对合成路径中的类胡萝卜素的代谢流造成扰动，表明CrtI是番茄红素的产量和纯度的决定因素。     

[Zr0.73(Cu0.59Ni0.41)0.27]87Al13合金过冷液相区热塑性成形研究

为探究[Zr_(0.73)(Cu_(0.59)Ni_(0.41))_(0.27)]_(87)Al_(13)非晶合金的热塑性成形性能以及绘制其对应的热加工图谱,用Gleeble3500型热模拟压缩实验机对该非晶合金进行不同参数下的热模拟压缩实验。结果表明,合金在压缩过程中变形行为由牛顿流变演变为非牛顿流变;同时,过高或过低的热加工温度均能导致合金晶化;进一步对数据分析得到该合金在不同热塑性成形参数下的功率耗散图与流变失稳图,并绘制出相应的热加工谱图,谱图分析结果表明,该合金在温度为420与430℃、应变速率为10~(-3) s~(-1)时具有较高功率耗散系数且没有失稳区域,因此,合金可选的热塑性加工参数为温度420～430℃,应变速率10~(-3) s~(-1)。     

Oxidation‐led decomposition of hexagonal boron nitride coatings on alloy substrates at 900 °C: Ti‐6Al‐4V

Hexagonal boron nitride (h‐BN) coatings on Ti‐6Al‐4V substrates undergo complete decomposition in air at 900 °C. This fate is similar to that of this ceramic material on chromia‐former alloys, and unlike that of a mass of powder treated in isolation. As the ceramic and alloy oxidize concurrently, outwardly diffusing aluminum (III) ions but not the predominant titanium (IV) ions react with the boron trioxide that forms around the h‐BN basal plane peripheries. Resultant aluminum borate is incorporated into the growing scale and the boron trioxide diffusion barrier is depleted. By this mechanism, the oxidation of h‐BN is maintained at an enhanced rate, until both this material and its oxide completely decompose. Liberated nitrogen from the oxidation of h‐BN can enter the underlying scale as a randomly distributed solute in rutile solid solution. The post‐coating oxide‐atmosphere interface comprises elongated aluminum borate crystallites protruding through at the boundaries between 3–5 at% nitrogen‐doped rutile grains. It differs significantly from that of oxidized, uncoated Ti‐6Al‐4V, which is occupied by a thin α‐alumina layer atop rutile. This interface does not change with an additional 72 h of heat‐treatment.     

激光立体成形TC4钛合金的热力场演化

激光立体成形能够实现高性能复杂零件的精确成形，但成形过程中的高温度梯度极易导致残余应力和变形，最终影响构件的几何精度和力学性能。通过搭建基板单边夹持原位热变形测量系统，探究了多道多层TC4钛合金成形件在激光立体成形过程中基板温度、变形的演化规律，分析了不同扫描策略对构件热应力场的影响。研究结果表明，构件的变形发展受其热历史驱使，扫描策略对成形件的热变形具有显著影响。     

Experimental and macro finite element modeling studies on conformability behavior of woven nylon 66 composite reinforcement

Abstract

In this study, 3D hemispherical forming experiments are conducted to analyze the conformability behavior of nylon 66 plain woven reinforcements with different weft densities. To make insight into the forming process, a macro finite element model is also proposed for 3D forming of a specific woven reinforcement by using the defined ‘Fabric’ material. The results show that the proposed FEM modelling is highly correlated with experimental findings in terms of forming energy values with small and insignificant errors values, which confirm well model validity. It shows that the nylon 66 composite woven reinforcement with a lower weft density exhibits a lower forming energy (toughness) and hence a higher conformability over a hemispherical surface. On the other hand, modeling outputs clearly indicate that more wrinkling intensity appear for woven reinforcement with a higher weft density.     

[成形过程的数据挖掘与深度学习方法]基于机器学习的管材弯曲回弹有效预测与补偿

采用基于优化的误差反向传播(BP)神经网络的机器学习算法建模，提出了考虑材料参数、几何参数等多因素的弯管回弹精确预测和高效控制方法。该方法通过引入非线性惯性权重及遗传算法的杂交算子，改进了粒子群优化(PSO)算法，进而通过改进的PSO算法对BP神经网络进行优化，构建了基于改进的PSO-BP神经网络机器学习回弹预测和补偿模型。以多种规格的铝合金数控弯管构件为对象，将实际生产中不同规格、批次、成形参数下回弹数据作为训练样本，实现了所建机器学习预测模型的应用验证。所建模型获得的预测结果平均相对误差为6.3%，与未优化的BP神经网络等传统模型相比，预测精度最大提高了18.5%，计算时间可从1.5 h缩短至300 s，同时实现了回弹预测与补偿精度以及计算效率的显著提高。     

吐哈盆地克尔碱凹陷煤层煤质特征与成煤环境

为了揭示吐哈盆地克尔碱凹陷不同矿区煤质形成条件，探讨该区煤质与成煤环境的关系，基于对主采煤层样品工业分析、有害组分及灰成分指标等数据分析，在对克尔碱凹陷地层分布、含煤岩系特征等基本地质条件分析的基础上，运用煤地质学、煤岩学、煤化学等理论和方法，系统总结凹陷内各矿区煤层赋存特征、煤质特征，探讨区内煤岩煤质与成煤环境的关系。结果表明：研究区自西向东划分6个主要矿区,区内煤层主要发育于中侏罗统西山窑组（J2x）和下侏罗统八道湾组（J1b）地层之中。研究区煤质呈低灰、低硫、高挥发分特征，煤灰成分以SiO2、Al2O3为主。综合分析表明，研究区中-下侏罗统主要煤层形成于湖泊-河流三角洲淡水沉积环境，具陆相成煤特征，成煤环境温暖潮湿。