Mechanical properties and wear behavior of Tin+1(Al,A)Cn (A = Ga,In, Sn,n = 1, 2) via quasi-high-entropy of single atomic thick A layer

The strengthening method of multi-element M-site solid solution is a common approach to improve mechanical properties of MAX phase ceramic. However, the research on capability of multi-element A-site solid solution to improve mechanical properties has rarely been reported. Thereupon, quasi-high-entropy MAX phase ceramic bulks of Ti₂(Al_1?xA_x)C and Ti₃(Al_1?xA_x)C₂ (A = Ga, In, Sn, x = 0.2, 0.3, 0.4) were successfully synthesized by in situ vacuum hot pressing via multi-elements solid solution. The multi-elements solid solution in single-atom thick A layer was confirmed by X-ray diffraction and X-ray photoelectron spectroscopy as well as by energy dispersive X-ray spectroscopy mappings. Effects of doped multi-elements contents on the phase, microstructure, mechanical properties, and high temperature tribological behaviors were studied. Results demonstrated that the Vickers hardness, anisotropic flexural strength, fracture toughness, and tribological properties of Ti–Al–C based MAX ceramics could be remarkably improved by constitution of quasi-high-entropy MAX phase in A layers. Moreover, the strengthening and wear mechanisms were also discussed in detail. This method of multi-element solid solution at A-site provides new way to enhance mechanical properties of other MAX phase ceramics.     

Microstructural and mechanical properties assessment of transient liquid phase bonding of CoCuFeMnNi high entropy alloy

The transient liquid phase (TLP) bonding of CoCuFeMnNi high entropy alloy (HEA) was studied. The TLP bonding was performed using AWS BNi-2 interlayer at 1050 °C with the TLP bonding time of 20, 60, 180 and 240 min. The effect of bonding time on the joint microstructure was characterized by SEM and EDS. Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time. For samples bonded at 20, 60 and 180 min, athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn₃Si intermetallic compound. For all samples, the γ solid solution was formed in the isothermal solidification zone of the bonding zone. To evaluate the effect of TLP bonding time on mechanical properties of joints, the shear strength and micro-hardness of joints were measured. The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints. The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min, respectively.     

A novel approach for bulk micromachining of 4H-SiC by tool-based electrolytic plasma etching in HF-free aqueous solution

Bulk micromachining of single-crystal SiC has been challenging due to its extreme stability both mechanically and chemically. To address this issue, a novel tool-based electrolytic plasma etching method is proposed, with which micropatterns and micro-holes are fabricated in SiC in a hydrofluoric acid-free aqueous solution with no need for masks. The material removal is the result of the combined effects of electrolytic plasma chemistry and physics. The chemistry refers to the reaction of Si with hydroxyl radical to form various SiO_x and with H to form silanes, and the reactions of C to form volatile carbon oxides or hydrocarbons, all of which are accomplished and enhanced under the electrolytic plasma atmosphere. Besides, the local high temperature of plasma thermally promotes the evaporation or dissolution of SiO₂ in NaOH solution. The tool-based electrolytic plasma etching method provides alternative approaches for the fabrication of SiC-based MEMS and devices.     

氮含量及固溶温度对21-6-9奥氏体不锈钢组织和硬度的影响

为了探讨氮含量及固溶温度对21-6-9不锈钢组织和硬度的影响,分别在950、1000、1050和1100 ℃对3种不同氮含量的热轧态21-6-9不锈钢进行1 h固溶处理,通过光学显微镜观察其组织结构,结合Thermo-Calc热力学计算对试验钢的微观组织进行分析,并对其进行硬度测试。结果表明,0.20%~0.28%N的21-6-9不锈钢热轧后沿轧制方向析出铁素体,且钢中铁素体经950~1100 ℃固溶处理可消除,当N含量达到0.34%时,试验钢中不再出现铁素体。随着固溶处理温度的升高,21-6-9不锈钢的晶粒组织长大,硬度降低。N含量的增加可显著提高固溶态21-6-9不锈钢的硬度,其增加程度随固溶处理温度的升高而减弱。     

A Novel Formulation of Glucose-Sparing Peritoneal Dialysis Solutions with l-Carnitine Improves Biocompatibility on Human Mesothelial Cells

The main reason why peritoneal dialysis (PD) still has limited use in the management of patients with end-stage renal disease (ESRD) lies in the fact that the currently used glucose-based PD solutions are not completely biocompatible and determine, over time, the degeneration of the peritoneal membrane (PM) and consequent loss of ultrafiltration (UF). Here we evaluated the biocompatibility of a novel formulation of dialytic solutions, in which a substantial amount of glucose is replaced by two osmometabolic agents, xylitol and l-carnitine. The effect of this novel formulation on cell viability, the integrity of the mesothelial barrier and secretion of pro-inflammatory cytokines was evaluated on human mesothelial cells grown on cell culture inserts and exposed to the PD solution only at the apical side, mimicking the condition of a PD dwell. The results were compared to those obtained after exposure to a panel of dialytic solutions commonly used in clinical practice. We report here compelling evidence that this novel formulation shows better performance in terms of higher cell viability, better preservation of the integrity of the mesothelial layer and reduced release of pro-inflammatory cytokines. This new formulation could represent a step forward towards obtaining PD solutions with high biocompatibility.     

水浴振荡碱消解-火焰原子吸收法测定土壤中六价铬

建立了水浴振荡碱消解-火焰原子吸收法测定土壤中的六价铬的方法。称取经风干、研磨并过0.15 mm孔径筛的土壤样品2.0 g(精确至0.01 g)置于150 mL锥形瓶中,加入25.0 mL碱性提取溶液,再加入400 mg氯化镁和0.5 mL磷酸氢二钾-磷酸二氢钾缓冲溶液,用聚乙稀薄膜封口,置于水浴恒温振荡器中。常温振荡样品5 min后,开启加热装置,加热水浴振荡至90～95℃,保持90 min。取下,冷却至室温。过滤,用硝酸调节溶液pH至7.5±0.5,将此溶液定容至50 mL容量瓶中,摇匀,待测。该方法采用水浴振荡碱消解的前处理方式进行土壤中六价铬的全消解,代替了磁力搅拌加热方式的消解,优化了前处理条件,简化了试验步骤,节约了分析测试时间,提高了分析效率,此方法还有利于处理大批量土壤样品。探讨了样品前处理提取温度的优化选择、氯化镁加入量的研究优化、提取时间的优化选择、pH值的优化以及三价铬干扰试验的影响。确认了最优化的仪器条件,对六价铬做了线性范围测试,曲线相关系数均在0.999以上。依据HJ 168—2020方法做了检出限,六价铬的检出限为0.5 mg/kg,以4倍检出限做测定下限,则测定下限为2.0 mg/kg。(取样量为2.0 g,定容体积为50 mL)。选取GBW(E)07251—255系列标准物质进行测试试验,试验结果的精密度和准确度均可满足土壤环境监测技术规范的要求。     

乌兰矿采矿现状及技术应对方案

本文分析了乌兰矿投产前期采矿现状及存在的主要问题,针对该矿所处蒙古国经济落后、投资风险大的现实状况,为避免生产中断、规避投资风险,早日回收前期投资考虑,采取了双斜坡道开拓、全尾胶结充填、高端壁空场嗣后充填采矿、多中段组合式连续开采等系列技术应对方案。大大降低了一次性投资规模及投资风险,前期投资得以快速回笼的同时,矿山产能也充分释放,确保了矿山的持续稳定,取得了较好的经济和社会效益。为海外地下近地表矿体开采矿山规避投资风险提供了很好的技术方案借鉴。     

Effects of four multi-compound freezing medium on the quality of red drum (Sciaenops ocellatus) during frozen storage

Taking air freezing (AF) as the reference, the effects of four types of multi-compound freezing medium for cryogenic liquid quick-freezing (immersion freezing, IF) on the freezing rate, quality and myofibrillar protein (MP) denaturation of red drum (Sciaenops ocellatus) fillets during frozen storage (−18°C) from days 0 to 90 were studied. Samples were gathered on days 0, 15, 30, 45, 60 and 90 for analysis. The results showed that IF groups (IF-1: 20% ethanol, 30% propylene glycol, 10% sodium chloride aqueous solution; IF-2: 20% ethanol, 20% propylene glycol, 10% glycerol, 10% sodium chloride aqueous solution; IF-3: 20% ethanol, 20% propylene glycol, 10% polyethylene glycol, 10% sodium chloride aqueous solution; IF-4: 20% ethanol, 20% propylene glycol, 5% glycerol, 5% polyethylene glycol, 10% sodium chloride aqueous solution) significantly shortened the time to cross the formation zone of maximum ice crystals while the freezing rate was 6.13 times higher than the AF group after adding 30% propylene glycol as the freezing medium. Furthermore, compared with the AF group, the IF groups significantly reduced losses in the water-holding capacity, the myofibrillar fragmentation index, microstructure damage, texture characteristics, drip loss and water migration (P < 0.05). In addition, the MP of IF groups had higher maximum transition temperatures (T_max1 and T_max2), total sulfhydryl content, Ca²⁺-ATPase activity and relative α-helix content compared with the AF group. In conclusion, IF could significantly increase the freezing rate of red drum fillets, and slow down quality deterioration and denaturation of MP during frozen storage for 90 days (−18°C). In particular, IF-2 (20% ethanol, 20% propylene glycol, 10% glycerol, 10% sodium chloride aqueous solution) was found to be more suitable for the immersion freezing of marine fish among the four multi-compound freezing medium.     

减水剂类型对赤泥—矿渣基地聚物注浆材料性能的影响及机理研究

针对赤泥等固体废弃物对环境危害性大且利用率低等问题,以碱激发赤泥-矿渣基地聚物注浆材料为 研究对象,研究了不同掺量的聚羧酸(PA)减水剂、醛酮缩合物(AKC)减水剂和萘系(N)减水剂对材料凝结时间、流动 性及强度等的影响,并通过 XRD、傅里叶红外光谱及 SEM 等设备对减水剂的作用机理进行研究。 结果表明:减水剂增 强了材料的流动性但降低了材料的剪切应力;N 和 PA 减水剂能缩短材料的凝结时间,但 AKC 减水剂会延长材料的凝 结时间;N 和 AKC 减水剂能提高材料的强度,但 PA 减水剂会降低材料的强度;N 减水剂对材料的综合性能提升效果 更加明显,其最优掺量为 0. 7%;减水剂对赤泥-矿渣基地聚物性能提升的作用机理主要是促进地聚合物凝胶的形成。 研究成果为拓展赤泥在工程上的使用途径和效率提供了理论指导。