浅谈压延铜箔光面色差的成因

针对压延铜箔在表面处理过程中光面易出现色差的问题,从设备、工艺、人员操作等方面进行成因探讨,并给出了应对措施。     

热轧双相钢生产现状、存在问题及发展趋势浅析

介绍了国内外热轧双相钢的发展现状；对热轧双相钢的成分体系和关键生产工艺进行了总结，指出了目前热轧双相钢在生产过程中存在的问题；提出了未来热轧双相钢的主要发展方向为低成本、高强度、低负荷、高表面质量和“以热代冷”。     

尼尔基主坝碾压式沥青混凝土心墙施工质量控制

尼尔基水利枢纽工程主坝为碾压式沥青混凝土心墙砂砾石坝（导流明渠段采用浇筑式沥青混凝土心墙），此种坝型在我国北方寒冷地区是首次采用。通过对原材料、沥青混凝土制备和现场铺筑的质量控制，经采用无损检测和钻孔取芯样对成墙质量的检验，工程优良率达到100％，并创造了多项国内施工记录，为国内沥青混凝土心墙施工积累了宝贵经验。     

连轧管“竹节”问题的研究

本文就各工艺参数对“竹节”的影响进行了较系统的试验。在此基础上，对连轧管“竹节”问题进行了分析，得出了“竹节”形态的基本特征；后“竹节”与轧制压力的关系；影响后“竹节”的主要工艺因素等一系列有意义的结果。对前、后“竹节”形态明显不同的原因进行了初步探讨。提出了“竹节”在线控制模型的初步设想。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

长输管道建设物流管理新模式——物资配送

长输管道工程是以线路管道与沿途站场为主要内容的建设工程,其物资配送有着不同于一般物流管理的特点,点多线长,且交通不便.文章结合西南成品油管道建设工程的物资配送实践,总结出长输管道物资配送的类型,并从机构设置、计划编制、台账和报表管理等方面介绍了物资配送的管理内容及经验,实践证明,这种物资配送方法不但使业主的物资管理人员大为减少,而且使长输管道工程的物资供应更加及时有序.     

热轧高强钢平整机辊径参数设计技术研究

基于高强钢平整机的生产工艺特点,结合板形与辊耗问题,将带材的出口前张力与辊间压力横向分布都均匀作为目标函数,把保证所有被平整高强钢产品的机械性能满足产品大纲要求作为约束条件,提出了一套针对热轧高强钢平整机的工作辊与支承辊辊径参数设计模型.其研究结果对指导宝钢分公司1880 mm热轧平整机的工艺参数的确定与技术谈判发挥了重要作用,并具有进一步的推广价值.     

实现卷板合理剪裁提高卷－带成材率的探讨

以热轧宽卷板作为焊管坯料，在宽度方向上纵向剪切成规格的带钢，各种焊管规格坯料搭配剪裁，提高管坯利用率     

双辊铸轧机生产工艺对组织和性能的影响

就用双辊铸轧机(TRC)生产薄、宽铸轧带技术进行研究并优化铸轧工艺。研究结果表明：3mm厚的铸轧带不仅表面变形．而且整个厚度内部层都发生变形，表面层的铝基中具有较高的合金元素饱和度。     

热轧左旋螺纹钢的开发

介绍了在轧钢厂二车间开发顾客需要的Φ18、Φ20、Φ22的热轧左旋螺纹钢。在原有Φ18、Φ20、Φ22热轧圆钢的工艺基础之上做工艺设计，经实际生产轧制，其产品质量完全符合顾客要求。