Determination of the width of the transition layer between the crystalline and amorphous zones in nylon 1010 by SAXS

The width of the transition layer between the crystalline and amorphous zones in nylon 1010 was determined by SAXS with point collimation and long-slit collimation, respectively. The width of the transition layer, E, was found to be 1.7 nm. The results show that the width of the transition layer is independent of crystallinity.     

Practical method for generation expansion planning based on dynamic programming

This paper presents an efficient method which provides the optimal generation mix and the optimal generation construction process. The approximation method in which the dynamic programming technique and gradient method are combined is applied to determine the optimal generation mix with hydropower generation technologies. The successive approximations dynamic programming (SADP) technique, which is very suitable for high-dimensional multistage decision process problems, is used for obtaining the optimal generation construction process. The effectiveness and feasibility of the developed technique are demonstrated on a practical power system model which has five types of generation technologies including a hydropower generation technology.     

Variations in Spectral Slope in Lake Taihu,a Large Subtropical Shallow Lake in China

Spectral slope (S), describing the exponential decrease of the absorption spectrum over a given wavelength range, is an important parameter in the study of of chromophoric dissolved organic matter (CDOM) dynamics, and also an essential input parameter in remote sensing models. Furthermore, S is often used as a proxy for CDOM composition, including the ratio of fulvic to humic acids and molecular weight. The relative broad range in S values reported in the literature can be explained by the different spectral ranges and fitting methods used. A single exponential model is used to fit the S values for 17 investigations involving 458 samples in Lake Taihu from January to October in 2004. The average S value was 15.18 ± 1.39 μm⁻¹ for the range of 280–500 nm, which fell within the range reported in the literature. The frequency distribution of S value basically obeyed a normal distribution. Significant differences in S values between summer and other seasons showed that phytoplankton degradation was one of the important sources of CDOM in summer, whereas CDOM mainly came from the river input in other seasons. Furthermore, the estimated S value decreased with increasing wavelength range used in regression. The maximum and minimum values derived from the regression were 17.89 ± 1.25 μm⁻¹ and 13.62 ± 2.11 μm⁻¹ for the wavelength ranges of 280–380 nm and 400–500 nm, respectively, a decrease of 23.9%. S values significantly decreased with the increase of CDOM absorption coefficients. CDOM absorption coefficients could be more appropriately estimated from exponential model introducing the variation of S with absorption coefficients, making them useful for a remote sensing bio-optical model of Lake Taihu. DOC-specific absorption coefficient a*(λ) and the parameter M describing molecular size of the humic molecules could also be used as a proxy for the sources and types of CDOM. A general relationship was found between S and a*(λ), and M values. S increased with the decrease of DOC-specific absorption coefficient and the increase of M corresponding to the decrease of molecular weight.     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

Unrestricted Hartree-Fock approximation of the extended emery model

We use an unrestricted self-consistent Hartree-Fock approach to calculate the nature of doping states in the three-band Hubbard model. It turns out that for physically relevant parameter values one hole is localized within a small spin-polarized region where five Cu spins are aligned in the same direction. The spin polarization and binding energy between these spinpolaronic states are investigated as a function of different parameters including a Holstein-type electron-phonon coupling on the Cu sites. At higher doping concentration we observe the occurrence of afmon states where the holes are localized in a ring-shaped area. Inside this ring the antiferromagnetic order parameter has inverse sign with respect to the residual antifer-romagnetically ordered plane.     

Modelling diffusion-controlled kinetics in equilibrium and driven alloys

Summary We introduce a very simple model for thermally activated atomic migration on a lattice, and several techniques to handle it. For thermodynamical systems, the model can be used for simulating decomposition paths taking into account relevant metallurgical features. Close to equilibrium, the simplest mean-field approximation of the model can be linearized with respect to the departure from equilibrium; one then gets a microscopic interpretation of classical phenomenological coefficients, such as mobility, interfacial transfer coefficient, rate constants for the coupled relaxation of concentration and order fields. Further away from the equilibrium, the nonlinearities can be taken into account in a consistent way. For driven alloys, i.e. alloys submitted to external forcing, forced atomic migration is added to the model and new features emerge: the model is supported by several experimental results some of which confirmed its predictions a posteriori.     

膛阻与小口径弹道炮弹道特性变化的分析

小口径弹道炮在使用初期,弹道特性值偏高,影响产品的验收和标准弹的鉴选.该文用膛阻理论解释弹道炮使用的各个时期的弹道特性变化,并介绍了“光膛”射击后,在弹道曲线下降段进行产品验收以及标准弹鉴选中的实际应用.     

石匣小流域坡地水土流失监测系统的建立及应用

以石匣小流域为坡地水土流失监测试点,以遥感及地理信息系统技术为手段,以坡地径流小区定位观测为依据,建立石匣小流域坡地水土流失监测系统,定位、定性、定量监测各种坡地类型的水土流失量、污染物流失量,为水土流失监测预报提供数据,为全市山区水土流失监测预报工作提供经验及方法,为制定水土流失防治方针政策及水土流失生态环境建设提供依据.     

HS2000分布式控制系统在小氮肥厂的应用

介绍了国产ＨＳ２０００分布式控制系统首次在山东禹城化工总厂尿素装置上成功应用的情况。     

Discrete element approach for mine dump stability analysis

Mine overburden dumps have posed significant safety issues in the operations of various unit operations of open pit min-ing especially the external dumps. The external dumps are composed of a mixture of fragmented rocks and loose soil. Their charac-teristic is comparable to heavily discontinuous solid mass. The conventional approach of limit equilibrium methods provide safety factors for the slope but nothing about the stress-strain characteristics of the large dump mass. The designs of dump location and their respective geometry are integrated for the know-how of the stability characteristics of these dumps. The discrete element method uses a circular disk to represent the granular solid mass and their interactions are described by the Newton's third law of motion. The displacement is described by the sliding of the circular disk. This work is focused on the modeling efficiency of the discrete element methods to represent the behaviour of mine dump masses with the specified joint plane for the limit equilibrium method. The advantage of the work lies on the ease of information retrieval at any point at the dump mass concerning the stress and strain histories, displacement, failures etc. which when integrated produces a better understanding of the stability of the dump masses.