2.3–21 GHz broadband and high linearity distributed low noise amplifier

This paper focuses on the design of a 2.3–21 GHz Distributed Low Noise Amplifier (LNA) with low noise figure (NF), high gain (S₂₁), and high linearity (IIP3) for broadband applications. This distributed amplifier (DA) includes S/C/X/Ku/K-band, which makes it very suitable for heterodyne receivers. The proposed DA uses a 0.18 μm GaAs pHEMT process (OMMIC ED02AH) in cascade architecture with lines adaptation and equalization of phase velocity techniques, to absorb their parasitic capacitances into the gate and drain transmission lines in order to achieve wide bandwidth and to enhance gain and linearity. The proposed broadband DA achieved an excellent gain in the flatness of 13.5 ± 0.2 dB, a low noise figure of 3.44 ± 1.12 dB, and a small group delay variation of ±19.721 ps over the range of 2.3–21 GHz. The input and output reflection coefficients S₁₁ and S₂₂ are less than −10 dB. The input compression point (P_1dB) and input third-order intercept point (IIP3) are −1.5 dBm and 11.5 dBm, respectively at 13 GHz. The dissipated power is 282 mW and the core layout size is 2.2 × 0.8 mm².     

FE-SEA方法在平台支持船噪声预报中的应用

平台支持船由于作业需要通常配备有动力定位系统,其在侧推工况下舱室噪声超标较为严重。针对这个问题采用计算流体力学(CFD)方法,得到侧推螺旋桨作用在导管上的脉动压力,并将时域计算结果转换成噪声计算的激励条件。采用有限元(FE)与统计能量分析(SEA)混合方法建立船体中频段FE-SEA耦合模型并建立船体高频段SEA模型,对某65 m AHTS船侧推工况下全频段(63 Hz~8000 Hz)舱室噪声进行预报,分析该船噪声分布规律及主要影响因素。并建立起全船的SEA模型,在中频段对比SEA与FE-SEA两种方法得到的舱室声压级频谱曲线,验证了使用混合模型的必要性。     

激光在线测厚振动分析与精度优化

激光测厚具有安全可靠、测量精度高、测量范围大等优点,广泛应用于纸张、电池极片等薄膜类材料厚度的在线测量。带材宽幅方向扫描测厚时由于扫描架往复运动会产生机械振动,影响在线测厚精度。针对该问题,以锂离子电池极片厚度测量为例,使用双激光差动式测厚平台对电池极片和铜箔分别进行厚度测量,然后对测厚数据进行频谱分析,探究其振动规律的相似性,并基于频谱分析结果采用滑动带阻滤波方式对测厚数据进行处理,滤波后极片和铜箔的厚度极差分别降低了33.4%和73.8%,有效过滤了机械振动导致的测量误差,可满足极片和铜箔厚度测量的精度要求。     

基于GA-BP的汽车风振噪声声品质预测模型

目前对于汽车风振噪声的优化研究主要以声压级（Sound pressure level，SPL）作为单一评价指标，既不能全面反映噪声的物理属性，也无法考虑人耳对噪声的主观认知过程。为准确评价风振噪声，引入声品质，运用大涡模拟（Large eddy simulation，LES）对风振噪声进行数值仿真，根据实车道路试验判断仿真的准确性；对仿真结果进行声品质客观评价与主观评价，综合声品质客观评价参数与声品质主观评价试验结果建立BP神经网络预测模型；利用遗传算法（Genetic algorithm，GA），进一步对BP神经网络的结构参数进行优化，建立GA-BP声品质预测模型。研究结果表明，GA-BP声品质预测模型在训练速度和预测精度上都优于BP神经网络预测模型。预测模型基于声品质主客观评价结果，其预测值可以代替传统的声压级评价指标，为风振噪声提供更为准确合理的评价。     

南方地区造纸车间钢屋面保温厚度的计算与分析

本文从内表面防结露、夏季隔热2个角度出发，对夏热冬冷及夏热冬暖地区代表城市采用的钢结构屋面的保温（隔热）层厚度进行计算分析。研究表明，在夏季室内温、湿度达到某一状态时，隔热厚度要大于冬季防结露的保温厚度。因此，夏热冬冷地区的造纸车间钢屋面保温层厚度应按夏季隔热计算确定，并进行冬季防结露验算；夏热冬暖地区按照冬季防结露计算即可。     

基于SVD和SSA-VMD降噪的轴承故障特征提取

针对强噪声背景下轴承故障特征提取困难的问题，提出一种基于奇异值分解和参数优化变分模态分解联合降噪的轴承故障特征提取方法(SSVMD)：首先，对原始信号进行奇异值分解(Singular Value Decomposition，SVD)处理，运用奇异值差分谱法选取有效奇异值并将原始信号重构得到初步降噪信号；其次，为防止故障信息丢失，将残余信号进行麻雀算法(Sparrow Search Algorithm，SSA)优化的变分模态分解(Variational Mode Decomposition，VMD）算法处理，得到最佳的模态个数K和惩罚参数α，选取峭度值最大、包络熵最小的IMF分量与初步降噪信号叠加得到最终降噪信号，并对信号进行包络分析；最后，通过仿真和试验数据分析得出，该方法能在信噪比很低的情况下降低噪声含量并提取轴承故障特征，为设备的状态监测和故障诊断提供理论依据。     

基于平均飞行航迹的CCO减噪效用研究

近年来，通过优化飞行程序降低机场飞机噪声影响成为机场环境保护的重要研究方向。文章首先建立了基于飞机“噪声-功率-距离”数据的噪声计算模型，介绍了平均飞行航迹以及连续爬升运行(Continuous Climb Opera-tion, CCO)离场程序的相关理论，最后以大型国际机场为实例，使用飞机平均飞行航迹进行噪声预测，运用综合噪声模型计算出噪声影响面积并绘制噪声影响等值线图，比较了CCO离场相对常规的标准仪表离场(Standard Instru-ment Departure, SID)的降噪效果。结果表明，CCO离场程序可有效降低机场噪声影响，在高噪声级影响区域的降噪效果更佳。     

Effect of slot-die configurations on coating gap dependence of maximum and minimum wet thicknesses

The dependence of the maximum and minimum wet thicknesses on the coating gap is derived for the slot-die coating process, under different slot-die configurations. Analytical expressions for the wet thickness and its derivative with respect to the coating gap are obtained using a simple flow model. The results indicate that, as expected, the minimum wet thickness increases linearly with the coating gap; however, the maximum wet thickness demonstrates a counterintuitive trend of decreasing as the coating gap increases, when a specific slot-die configuration is assumed. Moreover, the results are also validated by numerically solving the complete two-dimensional (2D) Navier–Stokes equation.     

Microstructure,mechanical, tribological,and oxidizing properties of AlCrSiN/AlCrVN/AlCrNbN multilayer coatings with different modulated thicknesses

Multilayer structure design is one of the most promising methods for improving the comprehensive performance of AlCrN-based hard coatings applied to cutting tools. In this study, four types of AlCrSiN/AlCrVN/AlCrNbN multilayer coatings, with different modulated thicknesses, were deposited to investigate their microstructure, mechanical, tribological, and oxidizing properties. All multilayer coatings exhibited grain growth along the crystallographic plane of (200) with a NaCl-type face-centered cubic (FCC) structure. The results show that, as the modulation thickness decreases from ～35 nm to ～10 nm, (1) the grain refinement effect is increasingly evident; (2) all multilayer coatings show a hardness of >30 GPa and an elastic modulus of >300 GPa. Both the ability to resist elastic strain to failure and the plastic deformation of multilayer coatings increase. In addition, their resistance to cracking reduces; (3) the wear rates of these multilayer coatings reduce successively from 1.78 × 10^?16 m³ N^?1 m^?1 to 7.7 × 10^?17 m³ N^?1 m^?1. This is attributed to an increase in self-lubricating VO_x and a decrease in adhesives from the counterparts; (4) the best high-temperature oxidation resistance was obtained for the multilayer coating with a modulated thickness of ～15 nm.     

Evaluation of the localized corrosion on Mg electrode surface by electrochemical noise technique

The symmetrical and asymmetrical electrodes made of Mg were studied in 0.1-M NaCl electrolyte adjusted at pH 12. The statistical and wavelet methods were employed for analyzing the electrochemical current noise (ECN) signals. The asymmetric configuration was used for electrochemical detection of filiform corrosion on Mg electrode. The real time scale of the dominant transients of the asymmetric electrodes was detected on the basis of the maximum peak in the SDPS plots. The SDPS values of the real time scale crystals of the ECN signals resulting from asymmetrical electrodes increased with the increase in immersion time due to the onset of filiform corrosion.