Ultrasonic-assisted wetting and soldering of AlN ceramic by using a nonactive solder (Sn9Zn) in air

AlN ceramic was successfully wetted and then joined with nonactive Sn9Zn eutectic solder assisted by ultrasonication in air. The effect of ultrasonic time on the formation of joint was studied. Results indicated that the defect-free joint can be obtained at an ultrasonic time of 5 s. Two regions, namely, AlN/Sn (s,_s) and AlN/Zn (s,_s), were found in the bonding interface. Zn and O accumulated in the AlN/Sn (s,_s) interface. An amorphous and nanocrystalline layer of ZnO formed in the hard-wet AlN surface. And Zn (s,_s) directly bonded with AlN. The low temperature and fast bonding of the AlN was attributed to the high pressure and temperature caused by cavitation effect. The shear strength of the joint increased from 10.6 MPa to 30.7 MPa when the ultrasonic treatment time increased from 5 s to 150 s. With the prolongation of ultrasonic time, more AlN ceramic particles entered the solder and acted as the reinforcing phase.     

Study on vapour dispersion and explosion from compressed hydrogen spill: Risk assessment on a hydrogen plant

Hydrogen produced from renewable resources is one of the cleanest fuels and could be used to store intermittent solar, wind and other energies. The main concern about using hydrogen is its hazards, such as high storage pressure, wide-range flammability, low mass density, and high diffusion. This study investigated the hazards of compressed hydrogen storage by developing a CFD model to understand the gas dispersion behaviour. The model was validated using the past experimental data and showed a good agreement, which could demonstrate the diffusion characteristics and gas stratification of a buoyant gas. A case study of an accidental release of compressed hydrogen from a storage tank was investigated to evaluate the risk of a hydrogen plant. A mathematical model of the jet spill was used to account for the choking effect from a high-pressure release to ensure the input velocity in CFD simulation is suitable for modelling gas dispersion using verified spatial and temporal scales, then the simulation results were used as inputs of vapour cloud explosions (VCEs) to investigate the potential overpressure effect. It was found the CFD model could predict a more reasonable flammable gas amount in cloud than using the bulk hydrogen release rate. The safety distance based on the overpressure prediction was reduced by 35%. The method proposed in this study can provide more validity for the consequence analysis as part of risk assessment.     

Impedance matching optimization of SiCf/Si3N4–SiOC composites for excellent microwave absorption properties

SiC fiber reinforced ceramic matrix composites (SiC_f-CMCs) are considered to be one of the most promising materials in the electromagnetic (EM) stealth of aero-engines, which is expected to achieve strong absorption and broad-band performance. Multiscale structural design was applied to SiC_f/Si₃N₄–SiOC composites by construction of micro/nanoscale heterogeneous interfaces and macro double-layer impedance matching structure. SiC_f/Si₃N₄–SiOC composites were fabricated by using SiC fibers with different conductivities and SiOC–Si₃N₄ matrices with gradient impedance structures to improve impedance matching effectively. Owing to its unique structure, SiC_f/Si₃N₄–SiOC composites (A3-composites) achieved excellent EM wave absorption performance with a minimum reflection coefficient (RC_min) of ?25.1 dB at 2.45 mm and an effective absorption bandwidth (EAB) of 4.0 GHz at 2.85 mm in X-band. Moreover, double-layer SiC_f/Si₃N₄–SiOC with an improved impedance matching structure obtained an RC_min of ?56.9 dB and an EAB of 4.2 GHz at 3.00 mm, which means it can absorb more than 90% of the EM waves in the whole X-band. The RC is less than ?8 dB at 2.6–2.8 mm from RT to 600 °C in the whole X-band, displaying excellent high-temperature absorption performance. The results provide a new design opinion for broad-band EM absorbing SiC_f-CMCs at high temperatures.     

Spin-state regulating of cobalt assisted by iron doping and coordination for enhanced oxygen evolution reaction

Customizing catalysts from the electronic structure, such as spin state, is an effective but challenging strategy for oxygen evolution reaction (OER). Herein, an ultrafine Co–Fe material highly dispersed on nitrogen carbide matrix is fabricated by coordination polymer and self-templating method to scrutinize the impact of spin state of Co on OER through Fe doping. The optimized catalyst shows boosted OER performance, which only requires overpotential of 333 mV at 10 mA cm^?2, outperforming other control samples and commercial RuO₂. The elevated local spin states of Co by Fe doping lead to charge transfer acceleration and fast generation of oxygenated intermediates, which is proved to account for the OER elevation. In addition, the long-term stability of Co–Fe material is guaranteed by the strong coordination of Co/Fe to the melamine-formaldehyde resin, which is used to adsorb metal ions, contributing to the high dispersion of active sites during the OER process.     

Synthesis and characterizations of highly responsive H2S sensor using p-type Co3O4 nanoparticles/nanorods mixed nanostructures

High-quality p-type semiconducting Co₃O₄ with mixed morphology of nanoparticles/nanorods are synthesized using a hydrothermal route for high response and selective hydrogen sulphide (H₂S) sensor application. XRD and Raman studies revealed the crystal structure and molecular bonding for obtained Co₃O_4, respectively. The nanoparticles/nanorods-like structures were confirmed for Co₃O₄ using FESEM and TEM analysis. The EDS and XPS spectra analysis were carried out for elemental composition and chemical atomic states of Co₃O₄. The Co₃O₄ sensor is investigated for gas sensing properties in dynamic conditions. The sensor exhibited the highest selectivity towards H₂S among various hydrogen-contained gases at 225 °C. The sensor revealed a high response of 357% and 44% for 100 and 10 ppm H₂S gas concentrations, respectively. The Co₃O₄ sensor exhibited a systematic dynamic resistance response for 100–10 ppm range H₂S gas. The excellent dynamic resistance repeatability of the sensor was shown towards 25 ppm H₂S gas. The response of Co₃O₄ sensor was investigated at different operating temperatures and H₂S concentrations. The sensor stability and H₂S sensing mechanism for the Co₃O₄ sensor have been reported. Highly uniform and mixed nanostructures of Co₃O₄ can be the potential sensor material for real-time high-performance H₂S sensor application.     

A high temperature and pressure framework for supercritical water electrolysis

Water electrolysis technologies aim to provide a significant increase in green hydrogen production efficiency. In this work, a framework was developed to explore the use of supercritical water for alkaline electrolysis. This framework was used to perform Arrhenius analysis as a function of potential, and to explore activation energies for sub- and supercritical water electrolysis. An analysis of the conductivity of solution unveiled a discontinuity in the trends between sub- and supercritical potassium hydroxide solution conductivity. Unlike prior work on supercritical water electrolysis, this work investigates trends in electrochemical parameters, the sources of these trends, and how they change between the sub- and supercritical regimes.     

Stress-strain behavior of geotextile: A proposed new indirect calculation using the static puncture test (CBR test)

Some of the main applications of geosynthetics include use as a hydraulic barrier in sanitary landfills, as a reinforcement element and in pavement engineering. In most cases, these materials are subject to the overlapping effects of tensile strength and puncture. This paper presents a review of indirect methods for calculation of stress and strain averages by means of the California Bearing Ratio (CBR) puncture strength test. In addition, a new calculation method is proposed based on the Kirchhoff plate theory, which interprets the behavior of thin circular plates subjected to a uniform normal loading. This new method enables analysis of the stress-strain in each stretch of the geosynthetic. The methodology is applied to four woven geotextiles of different weights. The results of the new calculation method yielded a better stress-strain correlation with direct tensile strength tests, presenting the smallest relative errors compared to the other indirect calculations reviewed. With the aid of a disk and pins, vertical displacement values at different points in the geotextiles were measured and showed good agreement with analytical predictions. Therefore, the static puncture test combined with the new proposed calculation method is a good alternative for determining the stress-strain parameters of geotextile.     

Preparation of high-purity SiC ceramics with good plasma corrosion resistance by hot-pressing sintering

High-purity SiC ceramic devices are applied in semiconductor industry owing to their outstanding properties. Nevertheless, it is difficult to densify SiC ceramics without any sintering additive even by HP sintering. In this work, high-purity and dense SiC ceramics were fabricated by HP sintering with very low amounts of sintering aids. Residual B content was only 556 ppm and relative density was more than 99.5%. Furthermore, thermal conductivity of as-prepared SiC ceramics was improved from 155 W m^?1 K^?1 to 167 W m^?1 K^?1 by increasing holding time and their plasma corrosion resistance was promoted in the meantime. The as-prepared high-purity SiC ceramics have broad application prospects in the field of semiconductor industry.     

Establishment of a color tolerance for yarn-dyed fabrics from different color-depth yarns

Yarn-dyed fabric is often woven from warp and weft yarns in the same color depth to ensure a uniform color appearance. The difference in color depth between warp and weft tends to result in the uneven color of the yarn-dyed fabric. This article aims to establish a color tolerance for yarn-dyed fabric that can be woven with a qualified color appearance but from the warp and weft yarns in different color depths. A total of 27 yarn-dyed fabric samples in three color series (red, yellow, and blue) were evaluated by using the yarn-dyed fabric from warp and weft yarns in the same color depth of 2% (on weight of fabric, owf) as the standard. Visual assessment and instrumental measurement of color were carried out to establish the color tolerance ellipse that was defined as CMC (Color Measurement Committee) color differences (2:1) of no more than 1.00. It was found that the color strengths (K/S) and color differences (ΔE_CMC(2:1)) of these fabric samples for each color series had linear relationships with the color depths of warp and weft yarns. The color tolerance ellipses indicated that, even though the warp and weft yarns had an apparent color difference, they could be woven in fabrics with relatively uniform color appearance and meet the requirements for yarn-dyed fabric. This work provided valuable insight into the production of qualified yarn-dyed fabrics from unqualified dyed yarns.     

异种铁素体耐热钢接头界面组织及其影响

综述了铁素体与铁素体异种金属焊缝（dissimilar metal welds，DMWs）接头界面组织及其影响。结果表明，在焊后热处理或运行温度下的铁素体钢DMWs接头的不均匀界面组织中，通常会形成脱碳层和增碳层。在铁素体钢DMWs焊接接头界面组织影响因素中，焊缝金属的化学成分有重要影响；焊后热处理规范（温度和时间）、工作温度下运行时间的影响较为突出；焊接工艺参数的影响亦不可忽略。异种钢接头界面处近缝区裂纹的产生，以及接头的蠕变强度随Larson Miller 参数增大而下降等不利影响，均为异种钢界面碳迁移行为所导致。焊缝成分控制法是接头界面组织控制或改善的必要条件，而脱碳层部位转移法能有效防止裂纹发生，亦是接头安全运行的重要工艺措施之一。