Fe-based bulk metallic glasses (BMGs) with high boron content have potential application as a coating material used in the framework for storing spent nuclear fuels to support their safe long-term disposal. The high glass forming ability (GFA) and large supercooled liquid region are therefore required for such Fe-based BMGs in either the glassy powder fabrication or the subsequent coating spraying. In order to meet these requirements, the influence of Nb content on the GFA of Fe57Cr10Zr8B18Mo7−xNbx (x=1–5, at.%) alloys was investigated, as Nb has positive roles in GFA and thermal stability of BMGs. The results indicate that a fully amorphous phase in the as-cast samples with 3 mm in diameter is obtained for both the Fe57Cr10Zr8B18Mo5Nb2 and Fe57Cr10Zr8B18Mo4Nb3 alloys. The corresponding supercooled liquid regions of the two BMGs are 78 K and 71 K, respectively. The mechanism for improving their GFA was analyzed based on the principle of metal solidification, the parameters for glass formation and thermal properties of the alloys. The compression strength and Vicker’s hardness of the two BMGs are 1,950 MPa and 1,310 HV, 2,062 MPa and 1,180 HV, respectively. The developed BMGs with high B content, good GFA, and very high hardness can be used as coating materials to the framework for spent nuclear fuels.
Based on the 3 factors and 3 levels orthogonal experiment method, compositional effects of Mg, Si, and Ti addition on the microstructures, tensile properties, and fracture behaviors of the high-pressure die-casting Al-x Mg-y Si-z Ti alloys have been investigated. The analysis of variance shows that both Mg and Si apparently infl uence the tensile properties of the alloys, while Ti does not. The tensile mechanical properties are comprehensively infl uenced by the amount of eutectic phase(α-Al + Mg_2Si), the average grain size, and the content of Mg dissolved into α-Al matrix. The optimized alloy is Al-7.49 Mg-3.08 Si-0.01 Ti(wt%), which exhibits tensile yield strength of 219 MPa, ultimate tensile strength of 401 MPa, and elongation of 10.5%. Furthermore, contour maps, showing the relationship among compositions, microstructure characteristics, and the tensile properties are constructed, which provide guidelines for developing high strength and toughness Al–Mg–Si–Ti alloys for high-pressure die-casting. 相似文献
Evaporative phase transitions are widely present in industrial production and daily life such as thin film processes and crystal growth. The evaporation of the liquid layer and the thermocapillary convection affect each other and restrict each other, making the energy transfer mechanism of the evaporation interface very complicated. To understand the evaporation characteristics of water in its low-pressure pure vapor environment, a series of experimental studies were carried out on the temperature distributions and evaporating rate of water evaporation in the annular pool. The cylinder temperature of the annular liquid pool is controlled between 3℃ and 15℃, and the evaporation environment pressure ranges from 394 Pa to 1467 Pa, when the temperature measurement starts, the depth of water is 10 mm. The results show that the temperature of the vapor side on the liquid-vapor interface is higher than that of the liquid side and there is an obvious temperature jump across the vapor-liquid interface. With the decrease of the pressure ratio, the evaporation rate increases, and the interface temperature jump is enlarged. Meanwhile, with the increase of the distance from the cylinder, the local evaporation rate decreases, thus, the temperature jump decreases. At the same pressure ratio, as the cylinder temperature increases, the heat flux from vapor side decreases, the temperature jump decreases at all measurement points. Within the experimental controlled parameters, the maximum temperature jump obtained in the measurements is 2.56℃. Due to the coupling effect of evaporation cooling and thermocapillary convection, there is a uniform temperature layer with a thickness of about 2 mm under the evaporation interface. The thickness of the uniform temperature layer near the cylinder is always larger than that in the middle of the evaporation interface. In the uniform temperature layer, the thermocapillary convection induced by radial temperature gradient transfers heat from the cylinder to the liquid-vapor interface to compensate for the latent heat of evaporation. Below the uniform temperature layer, the temperature rises rapidly due to heat conduction and buoyancy convection. 相似文献
Barium strontium alumino silicate (BSAS); (Ba0.6Sr0.4Al2Si2O8) was synthesized through solid state reaction between BaCO3, SrCO3, Al2O3 and SiO2 subjected to wet milling in isopropanol for about 24 h. The sequence of the solid state reaction was studied by subjecting to DG/DTG from room temperature to 1550 °C. The crystallographic phase evolution was confirmed by X-ray diffraction of the powders calcined in the range 1000 to 1300 °C for 2 h. The monoclinic celsian phase obtained at 1300 °C, pelletized through uniaxial pressing was sinterable to 67 to 78% density in the temperature range of 1300 to 1500 °C. The density improved to 75 to 94% after ball milling for 76 h, while ZrO2 addition further improved the density by 2%. The celcian phase of BSAS was dispersed in isopropyl alcohol, milled for about 24 h and spray coated on to plain SiC and mullite precoated SiC substrates. Sintering of coated samples and characterization for weight gain/loss, microstructure, scratch test prove that mullite + BSAS coating is more effective than single layer coating of BSAS on SiC substrates. 相似文献
针对立方调频(Cubic Frequency Modulated,CFM)信号的参数估计问题,提出了一种基于高阶模糊函数(High order Ambiguity Function,HAF)和相参积累三阶自相关函数(Coherently Integrated Trilinear Autocorrelation Function,CITAF)的参数估计方法。利用HAF将立方相位信号降阶为二次调频(Quadratic Frequency Modulated,QFM)信号,再利用CITAF完成参数估计。由于CITAF能够在时域和时延域完成信号能量的二维相参积累,其实现过程利用复乘、傅里叶变换和加法操作即可完成,因此该方法能够提高参数估计的分辨率和抗噪声干扰能力,并保持较低的计算量。实验结果证实了该算法的有效性和性能上的优越性。 相似文献