Nano TiC-Graphene-Cu composites fabrication by a modified ball-milling method followed by reactive sintering: Effects of reinforcements content on microstructure,consolidation, and mechanical properties

A two-step mechanical milling followed by a reactive sintering process was used to synthesize Nano TiC-Graphene-Cu composites from a mixture of Cu, Ti, and Graphene (GN) powders in four different compositions, and effects of reinforcements content on the microstructure and mechanical properties were studied. The results showed that a part of GN reacted with Ti atoms in the matrix, leading to the successful formation of hybrid nanocomposites. Uniform distribution of in-situ TiC with nanometer size and unreacted GN in the nanostructured Cu (Ti) solid solution were obtained. Addition of high percentage of the reinforcements led to an increase in the porosity and microhardness, coarsening of TiC nanoparticles, and decreasing the grain size of the matrix after sintering. The simultaneous presence of GN and TiC nanoparticles in the Cu matrix improved the hardness and wear resistance and reduced the friction coefficient by self-lubricating behavior. The nanocomposite with the nominal composition of Ti-40 vol % TiC showed the highest wear resistance and the lowest friction coefficient.     

Effect of nitrogen on deflagration characteristics of hydrogen / methane mixture

In order to study the influence of nitrogen on the deflagration characteristics of premixed hydrogen/methane, the explosion parameters of premixed hydrogen/methane within various volume ratios and different dilution ratios were studied by using a spherical flame method at room temperature and pressure. The results are as follows: The addition of nitrogen makes the upper limit of explosion of hydrogen/methane premixed gas drop, and the lower limit rises. For explosion hazard (F-number), hydrogen/methane premixed fuel with a hydrogen addition ratio of 10% has the lowest risk, and nitrogen has a greater impact on the dangerous degree of hydrogen and methane premixed gas whose hydrogen addition ratio does not exceed 30%. In terms of flame structure, the spherical flame was affected by buoyancy instability as the percentage of nitrogen dilution increased, but the buoyancy instability gradually decreased as the percentage of hydrogen addition increased. The addition of diluent gas reduces the spreading speed of the stretching flame and reduces the stretching rate in the initial stage of flame development. The laminar flame propagation velocity calculated by the experiment in this paper is consistent with the laminar flow velocity of the hydrogen/methane premixed gas calculated by GRI Mech 3.0. Considering the explosion parameters such as flammability limit, laminar combustion rate and deflagration index, when hydrogen is added to 70%, it is the turning point of hydrogen/methane premixed fuel.     

Microstructures and properties of nickel-titanium carbide composites fabricated by laser cladding

In this work, Ni/TiC composites were synthesized by the laser cladding technique (LCT). A scanning electron microscope (SEM), X-ray diffractometer (XRD), microhardness meter, electrochemical workstation, and friction and wear tester examined the microstructure, surface morphology, phase structure, microhardness, wear, and corrosion resistances of the Ni/TiC composites. These results indicated the Ni/40TiC composite contained finer equiaxed crystals than the Ni and Ni/20TiC composites. In addition, numerous TiC particles in the Ni/40TiC composite impeded growth of the nickel crystals, which resulted in the fine microstructure of the Ni/40TiC composite. The Ni, Ni/20TiC, and Ni/40TiC composites exhibited face-centered cubic (f c c) lattices. The average microhardness values of the Ni/20TiC and Ni/40TiC composites were approximately 748 HV and 851 HV, respectively. The Ni/40TiC composite had the lowest friction coefficient (0.43) among all three coatings, and only some shallow scratches appeared on the surface of the Ni/40TiC composite. The corrosion potential (E) of Ni/40TiC exceeded the Ni/20TiC composite, and both were larger than the Ni composite, which indicated the Ni/40TiC composite had outstanding corrosion resistance and the Ni composite had poor corrosion resistance. The corrosion current densities (i) of Ni, Ni/20TiC, and Ni/40TiC composites were 5.912, 4.405, and 3.248 μA/cm², respectively.     

Effect of SnO–P2O5–MgO glass addition on the ionic conductivity of Li1.3Al0.3Ti1.7(PO4)3 solid electrolyte

NASICON-type structured compounds Li_1+xM_xTi_2-x(PO₄)₃ (M = Al, Fe, Y, etc.) have captured much attention due to their air stability, wide electrochemical window and high lithium ion conductivity. Especially, Li_1.3Al_0.3Ti_1.7(PO₄)₃ (LATP) is a potential solid electrolyte due to its high ionic conductivity. However, its actual density usually has a certain gap with the theoretical density, leading the poor ionic conductivity of LATP. Herein, LATP solid electrolyte with series of SnO–P₂O₅–MgO (SPM, 0.4 wt%, 0.7 wt%, 1.0 wt%, 1.3 wt%) glass addition was successfully synthesized to improve the density and ionic conductivity. The SPM addition change Al/Ti–O bond and P–O bond distances, leading to gradual shrinkage of octahedral AlO₆ and tetrahedral PO₄. The bulk conductivity of the samples increases gradually with SPM glass addition from 0.4 wt% to 1.3 wt%. Both SPM and the second-phase LiTiPO₅, caused by glass addition, are conducive to the improvement of compactness. The relative density of LATP samples increases first from 0 wt% to 0.7 wt%, and then decreases from 0.7 wt% to 1.3 wt% with SPM glass addition. The grain boundary conductivity also changes accordingly. Especially, the highest ionic conductivity of 2.45 × 10^?4 S cm^?1, and a relative density of 96.72% with a low activation energy of 0.34 eV is obtained in LATP with 0.7 wt% SPM. Increasing the density of LATP solid electrolyte is crucial to improve the ionic conductivity of electrolytes and SPM glass addition can promote the development of dense oxide ceramic electrolytes.     

Novel hydrophilic N-halamine polymer with enhanced antibacterial activity synthesized by inverse emulsion polymerization

N-halamine-based antibacterial agents have high efficiency and rechargeable antibacterial properties. However, their applications are limited due to their complex synthetic process and fuzzy antibacterial mechanism. In this study, a novel N-halamine antibacterial polymer was synthesized by inverse emulsion polymerization and characterized by Fourier transform infrared, nuclear magnetic resonance, scanning electron microscopy, thermogravimetric analysis, and X-ray photoelectron spectroscopy. Due to the difficulty of purification, most of the subjects studied previously were hydrophobic polymers, while little research on hydrophilic polymers. In this experiment, this difficulty was overcome by controlling the dosage of sodium hypochlorite and methods of dialysis. Because of the complex cell structure of Gram-negative bacteria, it is difficult for N-halamines to release the oxidizing chlorine into the cell. However, the hydrophilic N-halamines can solve this problem, which showed a stronger antibacterial effect on Gram-negative Escherichia coli synthesized in this study. In addition, the particle size and hydrophilic property of the polymer were changed by changing the amount of initiator, and the differences in their antibacterial properties were studied. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47419.     

Developing high-performance laminated Cu/TiC composites through melt infiltration of Ni-doped freeze-cast preforms

Nacre-inspired laminated composites have been proven to possess a unique combination of strength and toughness. In this study, we fabricated nacre-mimetic Cu/TiC composites via unidirectional freezing of aqueous TiC slurries containing different amounts of NiO additives, followed by ice sublimation, carbothermal reduction of NiO to Ni during sintering and then gas-pressure infiltration of the Cu melt. The introduction of Ni greatly facilitated the densification of ceramic lamellae and enhanced the interfacial bonding between Cu and TiC. The resultant composites displayed outstanding damage tolerance and anisotropic electrical conductivities. Specifically, for an ～31?vol% TiC–Cu composite containing 24?wt% Ni in the ceramic lamellae (based on the TiC content), a fracture toughness (K_Jc) of 72.5?±?1.0?MPa·m^1/2, work of fracture of 53.4?±?3.5?kJ/m², bending strength of 725?±?11?MPa and longitudinal electrical conductivity of 22.7?MS/m (～60% of the Cu matrix) were achieved, which were approx. 81%, 536%, 122% and 97% higher than those of the Ni-free composite, respectively. Noticeable toughening was demonstrated to be a consequence of multiple cracking, plastic deformation and uncracked-ligament bridging of the metal layers, as well as crack deflection and blunting. On the other hand, significant strengthening resulted from tailoring the microstructures in the ceramic layers and at the Cu/TiC interface as a result of Ni doping. We believe that the facile strategy adopted herein provides an effective way to solve the problems of wetting and bonding related to metal infiltration and can be readily extended to the preparation of other nacre-inspired metal?ceramic composites.     

石墨烯增强钛基复合材料制备工艺与性能研究

以多层石墨烯为增强体,通过熔炼锻造(MF)和粉末冶金(PM) 2种工艺分别制备出规格为Φ10 mm的石墨烯增强钛基复合材料棒材。石墨烯在凝固过程中以TiC枝晶形态析出,变形后呈细小颗粒,其中Ti和C原子比约为2∶1。石墨烯和球形钛粉经过机械合金化和变形加工,在基体中反应形成薄片层。MF工艺对应的棒材拉伸强度可达476 MPa,延伸率保持在28%; PM工艺对应的棒材拉伸强度可达487 MPa,延伸率保持在30%。PM工艺可形成尺寸较小的薄片状石墨烯增强体,强化作用提升,同时塑性没有显著下降。     

卷取温度对超低碳T-3CA第二相析出的影响

 为研究卷取温度对超低碳T-3 CA中第二相粒子析出行为的影响，采用金相、TEM等检测手段，分析了580、630、680 ℃ 3个典型卷取温度下超低碳T 3 CA中第二相粒子的析出特性，结果发现卷取温度越高，热轧形成的TiC粒子尺寸越粗大，分布越稀疏。结合相关动力学计算分析了卷取温度对TiC粒子沉淀析出时临界晶核尺寸、相对形核率、相对沉淀析出时间的影响。结果表明，随着卷取温度由580提高到680 ℃，TiC粒子沉淀析出时临界晶核尺寸增大约1.0 nm，相对形核率降低约1.0个数量级，相对沉淀析出孕育时间增大约0.8个数量级。     

Structural,thermal and dielectric properties of AlN–SiC composites fabricated by plasma activated sintering

Highly dense AlN–SiC composites with various SiC additions (0–50?wt-%) were fabricated at 1800°C by plasma activated sintering. The effect of SiC addition on structural, thermal and dielectric properties as well as microwave absorbing performance of the composites was investigated. The thermal conductivity decreases with increasing SiC addition, from 68.7 W (m?K)^?1 for 0?wt-% SiC to 19.38?W (m?K)^?1 for 50?wt-% SiC. On the contrary, the permittivity and dielectric loss increase gradually, from 7.6–8.5 to 22–26.7 and from 0.02–0.1 to 0.2–0.53, respectively. AlN–SiC composite with better thermal and dielectric properties in 30?wt-% SiC, whose thermal conductivity and dielectric loss are found to be 24.88?W (m?K)^?1 and 0.15–0.74, respectively. Furthermore, the composite exhibits microwave absorbing performance with the minimum reflection loss (RL) of ?16.5 dB at 15.5 GHz and the frequency range of 2.6 GHz for RL below ?10 dB (90% absorption).     

基体稀释或基体匹配石墨炉原子吸收光谱法测定土壤样品中铅和镉

用石墨炉原子吸收光谱法测定土壤样品中Pb和Cd时,有时候直接按照方法标准GB/T 17141—1997操作,测定结果不能满足质控要求。研究结果表明,目标元素系列标准溶液中,分别含和不含土壤基体元素Na、Mg、Al、Si、Fe、Ca等元素混合成分时,校准曲线斜率明显不同。为减小基体效应的影响,基于文献调研和实验结果,对上述方法标准实验步骤进行了下列改进:(1)取相同体积实际样品消解液混合后,定量加入到用于建立校准曲线的系列标准溶液中,用于基体匹配;(2)对消解液进行适度稀释,仍采用标准溶液建立校准曲线。用4个土壤标样和土壤样品加标测定结果对改进后的方法进行了验证,结果表明,基体稀释法测定Pb的回收率范围分别为90.4%~114%;测定低含量Cd时,回收率范围为84.1%~125%。基体匹配法测定Pb和Cd的回收率范围分别为93.0%~105%和102%~119%,基本满足土壤样品中重金属回收率为80%~120%的质控要求。样品中痕量镉在测定下限附近时,应严格控制稀释倍数,或采用基体匹配法测定。改进后的操作步骤适合日常检测工作中大批量土壤样品中Pb和Cd的准确测定。