Structural Basis for the Function of the C-Terminal Proton Release Pathway in the Calcium Pump

The calcium pump (sarco/endoplasmic reticulum Ca²⁺-ATPase, SERCA) plays a major role in calcium homeostasis in muscle cells by clearing cytosolic Ca²⁺ during muscle relaxation. Active Ca²⁺ transport by SERCA involves the structural transition from a low-Ca²⁺ affinity E2 state toward a high-Ca²⁺ affinity E1 state of the pump. This structural transition is accompanied by the countertransport of protons to stabilize the negative charge and maintain the structural integrity of the transport sites and partially compensate for the positive charges of the two Ca²⁺ ions passing through the membrane. X-ray crystallography studies have suggested that a hydrated pore located at the C-terminal domain of SERCA serves as a conduit for proton countertransport, but the existence and function of this pathway have not yet been fully characterized. We used atomistic simulations to demonstrate that in the protonated E2 state and the absence of initially bound water molecules, the C-terminal pore becomes hydrated in the nanosecond timescale. Hydration of the C-terminal pore is accompanied by the formation of water wires that connect the transport sites with the cytosol. Water wires are known as ubiquitous proton-transport devices in biological systems, thus supporting the notion that the C-terminal domain serves as a conduit for proton release. Additional simulations showed that the release of a single proton from the transport sites induces bending of transmembrane helix M5 and the interaction between residues Arg762 and Ser915. These structural changes create a physical barrier against full hydration of the pore and prevent the formation of hydrogen-bonded water wires once proton transport has occurred through this pore. Together, these findings support the notion that the C-terminal proton release pathway is a functional element of SERCA and also provide a mechanistic model for its operation in the catalytic cycle of the pump.     

Environmental Enrichment Enhances Cav 2.1 Channel-Mediated Presynaptic Plasticity in Hypoxic–Ischemic Encephalopathy

Hypoxic–ischemic encephalopathy (HIE) is a devastating neonatal brain condition caused by lack of oxygen and limited blood flow. Environmental enrichment (EE) is a classic paradigm with a complex stimulation of physical, cognitive, and social components. EE can exert neuroplasticity and neuroprotective effects in immature brains. However, the exact mechanism of EE on the chronic condition of HIE remains unclear. HIE was induced by a permanent ligation of the right carotid artery, followed by an 8% O₂ hypoxic condition for 1 h. At 6 weeks of age, HIE mice were randomly assigned to either standard cages or EE cages. In the behavioral assessments, EE mice showed significantly improved motor performances in rotarod tests, ladder walking tests, and hanging wire tests, compared with HIE control mice. EE mice also significantly enhanced cognitive performances in Y-maze tests. Particularly, EE mice showed a significant increase in Ca_v 2.1 (P/Q type) and presynaptic proteins by molecular assessments, and a significant increase of Ca_v 2.1 in histological assessments of the cerebral cortex and hippocampus. These results indicate that EE can upregulate the expression of the Ca_v 2.1 channel and presynaptic proteins related to the synaptic vesicle cycle and neurotransmitter release, which may be responsible for motor and cognitive improvements in HIE.     

Thermal transport and chemical conversion in single reacting sorbent particles

The effects of particle size and carbon dioxide concentration on chemical conversion in engineered spherical particles undergoing calcium oxide looping are investigated. Particles are thermochemically cycled in a furnace under different carbon dioxide concentrations. Changes in composition due to chemical reactions are measured using thermogravimetric analysis. Gas composition at the furnace exit is evaluated with mass spectroscopy. A numerical model of thermal transport phenomena developed previously is adapted to match the physical system investigated in the present study. The model is used to elucidate effects of reacting medium characteristics on particle temperature and reaction extent. Experimental and numerical results show that (1) an increase in particle size results in a decrease in carbonation extent, and (2) the carbonation step consists of fast and slow reaction regimes. The reaction rates in the fast and slow carbonation regimes increase with increasing carbon dioxide concentration. The effect of carbon dioxide concentration and the distinction between the fast and slow regimes become more pronounced with increasing particle size.     

Improving water retention of chicken breast meats by CaCl2 combined with pulsed electric fields

Frozen poultry meat is the most widely consumed animal-based food. However, water loss often leads to quality loss of poultry meat. Therefore, the present study sought to investigate the combined effect of calcium chloride (CaCl₂) and pulsed electric fields (PEF) treatment on chicken breast meats and the mechanisms underlying protein degradation. The results showed that the synergistic effect was superior to the single treatment. Compared with the untreated group, the combination of CaCl₂ and PEF increased water holding capacity of chicken breast meats by 16.61% and decreased cooking loss by 28.93%. Low-field nuclear magnetic resonance (LF-NMR) results indicated that the synergistic treatment promoted water molecules' binding capacity in myofibrils of poultry meat, which exhibited higher immobilised water. Additionally, the combination of CaCl₂ and PEF led to increased degradation of proteins of high-molecular weight and surface hydrophobicity of myofibrillar protein. Furthermore, the extension of the protein molecule and microenvironmental changes promoted interaction between protein and water. In conclusion, the synergistic treatment of CaCl₂ and PEF enhanced water retention and improved physicochemical properties of the myofibrillar protein in chicken breast meats.     

Effect of heat treatment on the roughness and mechanical properties of dental lithium disilicate glass-ceramics

In dental clinics, it is common to perform small fitting adjustments in dentures using a micro-grinding tool after testing them in the patient's mouth. This procedure increases local roughness and can lead to formation of microcracks on the prosthesis surface. This study aimed to investigate the benefits of a post-finishing heat treatment to surface roughness and crack healing and its effect on the flexural strength of lithium disilicate (LD) dental glass-ceramics. Commercially available lithium metasilicate, Li₂SiO₃, samples were heat treated at 840 °C for 7 min to induce the phase transformation into LD, Li₂Si₂O₅. The LD samples were characterized by X-ray Diffraction, Scanning Electron Microscopy, Vickers hardness, Young’s modulus, and fracture toughness. One of the surfaces of the LD samples was sanded aiming to simulate the denture fitting adjustments performed in the dentist’s laboratory, generating a rough surface, Group 1. Half of the LD samples had their biaxial flexural strength evaluated by the piston-on-three-ball test (P–3B) and the other half were submitted to a second short-term heat treatment (840 °C - 5 min), Group 2, and later assessed by the P–3B. Roughness parameters in both groups were measured by 3D optical profilometry. After the crystallization heat treatment, formation of elongated LD crystals, Li₂Si₂O₅, 35% amorphous phase, and residual Li₃PO₄ was observed. In addition, the following mechanical property values were obtained: Vickers hardness = 5.8 ± 0.1 GPa, fracture toughness = 2.2 ± 0.1 MPa m^1/2, and Young’s modulus = 100.3 ± 0.3 GPa. The samples in Group 1 showed bending strength of 206 ± 30 MPa and the following roughness parameters: Ra = 0.45 ± 0.16 μm, Rz = 22.7 ± 6.7 μm, and PV = 27.7 ± 7.1 μm. In the samples in Group 2, the Ra, Rz and PV roughness parameters were 0.31 ± 0.12 μm, 5.2 ± 2.5 μm, and 9.2 ± 4.7 μm, respectively. With this decrease in roughness, the bending strength increased by 62%, with a mean value of 331 ± 59 MPa. In the need for machine finishing of LD-based glass-ceramic dental prostheses, the use of a second short-term heat treatment at 840 °C for 5 min generates considerable gains in bending strength, increasing the lifecycle of the prosthesis as a result of reduced surface roughness caused by softening of the remaining amorphous phase in the glass-ceramic. These conditions can be adapted to each chemical and crystallographic composition of the glass-ceramic under study.     

蒸压建材生产过程中钢渣安定性处理与活性化利用

钢渣安定性处理过程常常造成胶凝活性的损失。为此，本文利用改性助剂消除钢渣水化过程中产生的氢氧化物并生成胶凝产物，在蒸压建材的生产过程中实现钢渣安定性处理和游离氧化物的活性化利用，并避免单独处置钢渣造成的活性物质损失。研究表明，8%秸秆灰和3%磷酸二氢铵作为复合助剂制备的尾矿-钢渣蒸压试块体积稳定，抗压强度达24.0MPa。通过对蒸压样品游离氧化物消解率、化学结合水量及热重、XRD分析，得出钢渣安定性处理与活性化利用机制：硅质材料与钢渣中f-CaO水化生成的Ca(OH)₂结合迅速生成对体系力学强度有益的水化硅酸钙，避免因大量Ca(OH)₂积累造成体积膨胀；磷酸盐中的NH₄⁺、H₂PO₄^-与f-MgO结合生成磷酸铵镁及其他低溶度积复盐类矿物，进而消除因f-MgO水化生成Mg(OH)₂造成体积膨胀的隐患。试样在180℃蒸压4h后，f-CaO及f-MgO消解率分别可达86.28%、89.73%。本文将为利用钢渣大比例取代水泥和石灰生产蒸压建筑材料提供理论基础，对于提高钢渣利用率、减少碳排放具有重要价值。     

Experimental study on mitigating wind erosion of calcareous desert sand using spray method for microbially induced calcium carbonate precipitation

Wind erosion is one of the significant natural calamities worldwide, which degrades around one-third of global land. The eroded and suspended soil particles in the environment may cause health hazards, i.e. allergies and respiratory diseases, due to the presence of harmful contaminants, bacteria, and pollens. The present study evaluates the feasibility of microbially induced calcium carbonate precipitation (MICP) technique to mitigate wind-induced erosion of calcareous desert sand (Thar desert of Rajasthan province in India). The temperature during biotreatment was kept at 36 °C to stimulate the average temperature of the Thar desert. The spray method was used for bioaugmentation of Sporosarcina (S.) pasteurii and further treatment using chemical solutions. The chemical solution of 0.25 pore volume was sprayed continuously up to 5 d, 10 d, 15 d, and 20 d, using two different concentration ratios of urea and calcium chloride dihydrate viz 2:1 and 1:1. The biotreated samples were subjected to erosion testing (in the wind tunnel) at different wind speeds of 10 m/s, 20 m/s, and 30 m/s. The unconfined compressive strength of the biocemented crust was measured using a pocket penetrometer. The variation in calcite precipitation and microstructure (including the presence of crystalline minerals) of untreated as well as biotreated sand samples were determined through calcimeter, scanning electron microscope (SEM), and energy-dispersive X-ray spectroscope (EDX). The results demonstrated that the erosion of untreated sand increases with an increase in wind speeds. When compared to untreated sand, a lower erosion was observed in all biocemented sand samples, irrespective of treatment condition and wind speed. It was observed that the sample treated with 1:1 cementation solution for up to 5 d, was found to effectively resist erosion at a wind speed of 10 m/s. Moreover, a significant erosion resistance was ascertained in 15 d and 20 d treated samples at higher wind speeds. The calcite content percentage, thickness of crust, bulk density, and surface strength of biocemented sand were enhanced with the increase in treatment duration. The 1:1 concentration ratio of cementation solution was found effective in improving crust thickness and surface strength as compared to 2:1 concentration ratio of cementation solution. The calcite crystals formation was observed in SEM analysis and calcium peaks were observed in EDX analysis for biotreated sand.     

Determination of optical and structural properties of lithium silicate ceramics with different ratios of Sm doped

In this study, the synthesis and luminescence characterization of Samarium (Sm³⁺) doped lithium metasilicate (Li₂SiO₃) phosphor ceramic were investigated. It was presented and discussed the results obtained on the luminescence and other optical studies such as X-ray diffraction (XRD), optical absorption and luminescence properties of Li₂SiO₃:Sm³⁺ phosphor ceramic. The Li₂SiO₃ compound was shown a characteristic phase in XRD. The doping in the lithium compound was not having a significant effect on the basic crystal structure of the material. The maximum photoluminescence (PL) emission for Sm³⁺ doped Li₂SiO₃ was observed at 554, 583, 641, 725 nm and bore resemblance to the visible region of the spectrum. The glow curves of all synthesized materials have a complex peak structure after being irradiated with a ⁹⁰Sr–⁹⁰Y beta source. In addition, the peak between 400 and 600 nm was seen in the radioluminescence (RL) spectrum because of a wide peak thought to be caused by silicate.     

Nucleation and crystallization of Ba2Si3O8 spherulites in a barium aluminum silicate glass,and mechanical properties of the obtained glass-ceramics

The effect of spherulitic crystallization on the elastic moduli and fracture toughness of a barium aluminum silicate glass was investigated. The crystallization process results in Ba₂Si₃O₈ phase and is initiated from Ba rich nuclei. Nucleation is optimal in the 690-720 °C interval. Young’s modulus is increased by 12.5% when the glass-ceramic conversion is nearly complete. Nevertheless, as the size and the volume fraction of crystals are increased, some microcracking shows up upon cooling from the crystallization temperature. An optimal improvement of the fracture toughness (SEPB method) by 27 % is observed for a 49 % volume fraction of 5 to 10 μm large spherulites.     

Extraction and characterization of hydroxyapatite-based materials from grey triggerfish skin and black scabbardfish bones

The conversion of food industry by-products to compounds with high added value is nowadays a significant topic, for social, environmental, and economic reasons. In this paper, calcium phosphate-based materials were obtained from black scabbardfish (Aphanopus carbo) bones and grey triggerfish (Balistes capriscus) skin, which are two of the most abundant fish by-products of Madeira Island. Different calcination temperatures between 400 and 1000°C were employed. Materials obtained from calcination of bones of black scabbard fish were composed by homogeneous mixtures of hydroxyapatite (Ca₁₀(PO4)₆(OH)₂, HAp) and β-tricalcium phosphate (β-Ca₃(PO₄)₂, β-TCP). Because of the high biocompatibility of HAp and the good resorbability of β-TCP, these natural biphasic materials could be very relevant in the field of biomaterials, as bone grafts. The ratio between HAp and β-TCP in the biphasic compound was dependent on the calcination temperature. Differently, the material obtained from skin of grey triggerfish contained HAp as the main phase, together with small amounts of other mineral phases, such as halite and rhenanite, which are known to enhance osteogenesis when used as bone substitutes. In both cases, the increase of calcination temperature led to an increase in the particles size with a consequent decrease in their specific surface area. These results demonstrate that from the fish by-products of the most consumed fishes in Madeira Island it is possible to obtain bioceramic materials with tunable composition and particle morphology, which could be promising materials for the biomedical field.