Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

Influences of chip serration on micro-topography of machined surface in high-speed cutting

Saw-tooth chip changes from macroscopically continuous ribbon to separated segments with the increase of cutting speed. The aim of this study is to find the correlations between chip morphology and machined surface micro-topography at different chip serration stages encountered in high speed cutting. High strength alloy steel AerMet100 was employed in orthogonal cutting experiments to obtain chips at different serration stages and corresponding machined surfaces. The chips and machined surfaces obtained were then examined with optical microscope (OM), scanning electron microscope (SEM), and white light interferometer (WLI). The result shows that chip serration causes micro-waves on machined surface, which increases machined surface roughness. However, wave amplitudes (surface roughness) at different serration stages are different. The principal factor influencing wave amplitude is the thickness of the sawed segment (tooth) of saw-tooth chip. With cutting parameters in this study, surface roughness contributed by chip serration ranges from 0.39 μm to 1.85 μm. This may bring on serious problems in the case of trying to replace grinding with high-speed cutting in rough machining. Some suggestions have been proposed to control the chip serration-caused surface roughness in high-speed cutting based on the results of the current study.     

一种微透镜阵列的研制

介绍一种利用表面张力的作用、以光纤作材料、用分离的自聚焦透镜制作微透镜阵型的方法，这种方法具有制作工艺简单、无须昂贵设备等优点，用此方法实际制作了具有良好连续面型的微透镜阵列，并对制作的微透镜阵列进行了测试，效果较好。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

Formation and growth mechanism of TiC crystal in TiC_p/Ti composites

1　ＩＮＴＲＯＤＵＣＴＩＯＮＰａｒｔｉｃｌｅｓｒｅｉｎｆｏｒｃｅｄｔｉｔａｎｉｕｍａｌｌｏｙｍａｔｒｉｘｃｏｍｐｏｓｉｔｅｓ(ＴＭＣｐ)ｈａｖｅｗｉｄｅａｐｐｌｉｃａｔｉｏｎｆｉｅｌｄｓｆｏｒｔｈｅｉｒａｔｔｒａｃｔｉｖｅｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇ     

聚合物-金属界面相形貌的研究

环氧树脂在 Al 合金表面生成纤维状的界面相结构,其形成、发展和特征与树脂的体系、交联反应条件以及 Al 合金的表面状态有关。环氧树脂的基础相为颗粒状的超结构组织。聚合物界面相的力学破坏表现为纤维体的拉伸、变形和断裂,而基础相在纯剪切受力时出现在45°方向的裂纹,并发展导致连接层的破坏。     

火焰图像特征在火灾数字图像识别中的运用

火焰尖角数目和圆形度是早期火灾火焰的主要特征,本文主要论述了如何在数学形态学基础上,利用火灾火焰的两个特点判断和识别早期火情。实验中,对火焰的二值图像进行开运算,即先腐蚀,再膨胀,目的是为了对火焰图像进行形态学滤波,去噪。从实验结果可以看出,该算法可以很好的识别火焰和干扰源。     

Use of recycled copper slag for blended cements

Copper slag is a by‐product generated during smelting to extract copper metal from the ore. The copper slag obtained may exhibit pozzolanic activity and may therefore be used in the manufacture of addition‐containing cements. In this paper the effect of the incorporation of the copper slag in cement is measured. Blends of copper slag with Portland cement generally possess properties equivalent to Portland cement containing fly ash, but very different to the silica fume incorporation. Copper slag and fly ash reduce the heat of hydration more effectively than silica fume in mortars. The replacement of 30% cement by copper slag reduces the flexural and compressive strength in a similar way to fly ash; however, after 28 days, the reduction is less than the percentage of substitution. Hydrated calcium aluminate phases were analysed using scanning electron microscopy (SEM) and X‐ray diffraction (XRD) techniques. The pozzolanic activity of copper slag is similar to that of fly ash and higher than silica fume. In the presence of low water/cement ratios, certain pozzolanic materials produce a very compact cement paste that limits the space available for hydration products, a determining factor in the formation of hydrated calcium aluminates. SEM was found to be a useful analytical technique when aluminates are formed and can be clearly detected by XRD. Copyright © 2008 Society of Chemical Industry