镍层耐硝酸腐蚀性测试——一种简单的预先探测ENIG镍层“黑盘”现象的测试方法

随着更加精细的SMT、BGA等表面贴装技术的运用,化学沉镍金(ENIG)作为线路板最终表面处理得到了越来越广泛的应用,同时可怕的“黑盘”现象也随之更广泛地“流行”起来,直接导致贴装后元器件焊接点不规则接触不良。为了贯彻执行最好的流程控制和采取有效的预防措施,了解这种焊接失败的产生机理是非常重要的,及早的观测到可能发生“黑盘”现象的迹象变得同样关键。本文介绍了一种简单的预先探测ENIG镍层“黑盘”现象的测试方法-镍层耐硝酸腐蚀性测试,这种测试可以用于作为一种常规的测试方法监测一般化学沉镍溶液在有效使用寿命范围内新鲜沉积的镍层的质量。利用Weibull概率统计分析在不同的金属置换周期(MTO)下镍层的可靠性能表现。结合试验结果得出了一个镍层耐硝酸腐蚀性的判定标准。     

熔融碳酸盐燃料电池阴极材料的导电性

通过交流阻抗方法研究了熔融碳酸盐燃料电池阴极材料锂镍氧化物、锂钴氧化物和锂铁氧化物的导电性能。结果表明:锂镍氧化物电极的导电性最好,锂钴氧化物电极的导电性次之,锂铁氧化物电极的导电性最差;它们的导电性都随着温度的升高而按指数规律增加;在合成锂钴氧化物(或锂铁氧化物)的过程中,使Li2CO3轻微过量,可以提高锂钴氧化物(或锂铁氧化物)电极的导电性,而且在同一温度下,随着nLi∶nCo(或nLi∶nFe,摩尔比)值的增大,锂钴氧化物(或锂铁氧化物)电极的导电性显著增加。     

The electropolymerization of pyrrole at a CuNi electrode: corrosion protection properties

Pyrrole was successfully electropolymerized at a copper–nickel electrode in a near-neutral sodium oxalate solution containing Cu²⁺ cations to generate a homogenous and adherent polypyrrole film. The presence of the Cu²⁺ ions increased both the rate of the electropolymerization reaction and the adherence of the polymer at the CuNi interface. In the absence of these cations, oxidation of the electrode occurred generating a nickel-rich layer that was not sufficiently conducting, under the electropolymerization conditions employed, to facilitate the electron-transfer reaction and the electropolymerization of pyrrole.These films remained stable and exhibited significant corrosion protection properties in acidified and neutral 0.1 mol dm⁻³ NaCl solutions even on polarization of the electrodes to high anodic potentials.     

Electrochemical intercalation in NiOx thin films

In this work we investigated the mechanism of the electrochemical intercalation reactions in rf sputtered nickel oxide thin films electrodes by two techniques: mechanical stress change measurements by means of an optical technique and mass changes using an electrochemical quartz microbalance (EQCM). The experiments were performed in alkaline electrolytes containing cations of the first column of the periodic table. Reversible mass and volume changes were observed. In order to explain these experimental results, an exchange reaction is proposed, in which the oxidation process is accompanied by the deinteractional of a relative large number of “light” cations, simultaneously with the intercalation of a smaller number of heaviest cations.     

Magnetic properties of nickel filament polymer-matrix composites

The magnetic properties of polyethersulfone-matrix composites with 3-19 vol.% polycrystalline nickel filaments (0.4 (im diam) were investigated. These filaments were found to exhibit hysteresis energy loss 10800 J/m³ of nickel and coercive force 16.9 kA/m, compared to corresponding values of 4930 J/m³ and 4.7 kA/m for 2 μ.m diam polycrystalline nickel fibers, 1020 J/m³ and 0.5 kA/m for 20 μm diam polycrystalline nickel fibers, and 1280 J/m³ and 2.3 kA/m for solid polycrystalline nickel.     

化学镀镍合金在电子工业中的应用

对化学镀镍合金铁工艺和性能特性及其在电子工业中的应有委展现状作了评述。化学镀镍合金具有镀层均匀，适用基材广，结合力高，硬度高，优良的耐磨、耐蚀性，可焊性好和特殊的电磁性能等特性，在电子工业中获得了广泛的应用。文中着重介绍了化学镀镍合金在磁盘、电磁屏蔽、微电路、半导体、连接器及薄膜电阻上的应用情况。这些案例说明，合理应用化学镀镍合金技术，有利于提高电子元器件的质量，降低成本，促进技术进步。     

钛合金的银脆,镉脆敏感性及其控制

利用慢应变速率拉伸技术（ＳＳＲＴ），并结合恒载实验，较全面地研究了Ｔｉ－６Ａｌ－４Ｖ合金的银脆行为、固态与液态镉脆行为，确定了应变速率、接触条件、热处理制度、试样取向、温度等因素对Ｔｉ－６Ａｌ－４Ｖ合金银脆与镉脆敏感性的影响，探讨了Ｎｉ阻挡层对控制Ｔｉ－６Ａｌ－４Ｖ合金和ＴＣ１１合金银脆开裂的作用。     

镀镍云母导电复合材料的研究

对云母粒子化学镀镍及以LDPE为基材,镀镍云母粒子为填料制备的导电复合材料进行研究。认为此种导电复合材料只有质量轻、强度大及良好的导电等性能。     

Crystalline and viscoelastic properties of branched polyethylenes synthesized using bidentate nickel (II) catalyst

In this work, five branched polyethylenes with different branching units were synthesized using bidentate nickel (II) catalyst containing -diimine ligands. For comparison, one linear polyethylene was also prepared using tridentate iron (II) catalyst containing -diimine ligand. The crystalline structure of the polyethylenes was investigated using X-ray diffraction (XRD) and polarized optical microscope. The crystalline properties were also measured by differential scanning calorimeter (DSC). Viscoelastic properties of the polyethylenes were investigated using rheometric dynamic analyzer. The DSC and XRD results showed that highly branched polyethylenes exhibit no melting points and no predominating crystalline forms, while the linear polyethylene exhibits clear orthorhombic (110) and (200) reflections on XRD pattern and a clear melting point at 118 °C. The viscoelastic properties of the branched polyethylenes were very complicated due to the combined effect of the molecular weight difference and the degree of chain branching as well as the branching structure.     

Density measurements on levitated liquid metal droplets

Electromagnetic levitation is a useful tool for measuring thermophysical properties of high-temperature melts such as liquid metals. Due to its noncontact nature, the undercooled regime is also accessible. Density and thermal expansion of a levitated drop can be derived from volume measurements, if its mass is known. Assuming cylindrical symmetry, the volume of a drop can be determined from its cross section. Using photography, such measurements on liquid metals have been performed in the past. Here we present an improvement of this method, which replaces the photographic camera with a CCD videocamera and subsequent digital image processing. This reduces the time effect required to obtain the results and allows one to average over disturbing surface oscillations. The specific problems of digital image processing, namely resolution and edge detection, are addressed and results on nickel are presented.Paper presented at the Fourth International Workshop on Subsecond Thermophysics, June 27–29, 1991, Köln, Germany.