Grain refinement and superplasticity of pipes processed by high-pressure sliding

ABSTRACT

The high-pressure sliding (HPS) process was applied for grain refinement of a pipe form of an Al-3wt%Mg-0.2wt%Sc alloy by developing two types of straining techniques (called in this study anvil sliding and mandrel sliding). To achieve a homogeneous microstructure throughout the cross-section of the pipe, the sample is rotated around the longitudinal axis every after sliding operation by introducing multi-pass technique, named multi-pass HPS (MP-HPS) as developed earlier for rods. The MP-HPS-processed sample shows ultrafine-grained structures with an average grain size of ～260 and ～300?nm after the HPS processing using anvil sliding and mandrel sliding. The samples also exhibit superplasticity with total elongations well more than 400%, respectively. A finite-element method is used to simulate the evolution of strain in the HPS processing and demonstrates that the simulation well represents the experimental results.     

生物医用Ti-29Nb-13Ta-5Zr合金的超塑性行为

采用拉伸速率突变法,研究Ti-29Nb-13Ta-5Zr(Ti-29-13)合金冷轧后在700~800 ℃和5′10-4~1′10-2 s-1应变速率范围内的高温变形行为和变形机制,并与典型β钛合金Ti-15V-3Cr-3Sn-3Al(Ti-15-3)进行比较。结果显示两种合金中均出现了非连续屈服现象,Ti-29-13合金的亚晶行为不同于Ti-15-3合金。Ti-29-13合金的延伸率低于Ti-15-3合金,应力指数n几乎恒定为3.3,变形激活能为152~161 kJ/mol;Ti-15-3合金在730 ℃以上的n值为2.3~2.5,变形激活能为173~176 kJ/mol。     

双相NiAl金属间化合物超塑性

研究双相Ni-31Al金属间化合物的高温变形行为。结果表明,该合金在950~1075℃温度范围,1.25×10-4~8×10-3s-1应变速率范围内呈超塑性变形。在温度为1000℃、应变速率为5×10-4s-1时,最大延伸率可达281.3%。显微结构分析表明,超塑性变形过程中两相具有很好的协调变形能力,超塑性变形后原始组织拉长、细化。双相Ni-31Al金属间化合物超塑性变形机制可能为连续动态回复与再结晶。     

搅拌摩擦加工AZ31镁合金的超塑性

对搅拌摩擦加工AZ31镁合金的微观组织和拉伸力学行为进行了研究。结果表明,通过搅拌摩擦加工,热轧AZ31板材的平均晶粒尺寸由92.0μm细化到11.4μm。搅拌摩擦加工板材在高温下具有优异的塑性,伸长率在温度为723K和应变速率为5×10-4s-1的条件下达到1050%。该材料还具有高应变速率超塑性,在723K和1×10-2s-1的条件下伸长率达到268%。在相同实验条件下,母材由于晶粒尺寸粗大,没有显示出超塑性。     

工业牌号铝合金的超塑性能及微观组织演化特征

采用实验方法研究国外广泛用于汽车车身板件冷冲压成形的工业牌号铝合金板材AA5182和6016的超塑性能,以及超塑变形中微观组织的演化特征。通过超塑性单向拉伸试验、材料变形前后的微观组织观察和自由胀形试验,揭示出铝合金AA5182具有一定的超塑性能,而铝合金6016的超塑性能很低。铝合金AA5182在温度为375℃、应变速率为1.67×10-3/s时,材料的延伸率达到210%,m值达到0.25;在温度为500℃、应变速率为1.67×10-2/s时,材料延伸率达到225%,m值达到0.35。     

电场作用下1.6%C-UHCS/40Cr钢的超塑性焊接

基于对40Cr钢淬火后与经热机械处理超高碳钢1.6% C-UHCS电场作用下超塑性焊接可行性的分析,在非真空、无保护气氛下,进行了电场作用下1.6% C-UHCS/40Cr的超塑性焊接工艺试验.结果表明,当施加试样接正极、环状电极接负极的电场时,可明显提高40Cr钢淬火后与经热机械处理超高碳钢1.6% C-UHCS的超塑性焊接效果.与不加电场相比,当两者在外加电场＋3 kV/cm、预压应力56.6 MPa、焊接温度780℃、初始应变速率1.5×10-4/s的条件下,经20 min超塑性焊接,接头强度提高26.8%.     

添加剂对电沉积Al2O3/Ni-Co复合材料力学性能的影响

通过脉冲电沉积技术制备出含1,4-丁炔二醇或糖精为添加剂的Al2O3/Ni-Co复合材料,采用TEM、EDS等方法分析了含2种添加剂的Al2O3/Ni-Co复合材料的微观组织结构,比较了添加剂对材料光洁度、显微硬度、室温塑性以及高温塑性的影响,并通过SEM对变形后材料的显微结构进行了表征.以糖精为添加剂所制备的AlO3...     

TC6钛合金的超塑变形机制研究

提出了一种全新的超塑性研究方法：基于m值的高效超塑变形机制。采用该方法对TC6钛合金进行高温拉伸实验,研究其超塑性能,并与最大m值法超塑性进行比较分析。实验结果表明,细晶组织的该合金具有优良的超塑性,最佳变形温度在900℃,最大m值超塑变形可以获得20倍的最大延伸率;基于m值的高效超塑变形可以显著提高超塑成形效率,在获...     

工程陶瓷材料的制造、加工与超塑性

简要介绍工程陶瓷材料的制造与机械加工研究的进展 ,以及当前我国工程陶瓷材料超塑性研究的结果与动向     

GRAIN BOUNDARY CHARACTER DISTRIBUTION, TEXTURE AND SUPERPLASTIC DEFORMATION BEHAVIOR OF AN AI-Li ALLOY

The grain boundary character distribution and thetexture of 2091 Al-Li alloy recrystallized at different temperatures were measured by TEM and X-ray techniques respectively. The occurrence frequency of low-energy boundaries decreases with increasing recrystallization temperature, while the frequency of highenergy boundaries increases. The strongest component of recrystallization texture in the test temperature range is {011} <111>. The relative intensity of the texture tends to decrease with increasing recrystallization temperature. The material which contains a high frequency of low-energy boundaries exhibits lower deforming stress and high elongation.