药物相互作用研究在新药研发和审评决策中的应用

药物相互作用改变了剂量效应关系，可能会降低疗效或增加毒性，是临床应用中合并用药治疗时重要的考虑因素。预测具有临床意义的药物相互作用是药物研发过程中获益风险评估的重要环节。本文概述了药物研发过程中药物相互作用研究的目的和意义，体内和体外研究的主要内容；梳理分析了2020年国家药品监督管理局（National Medical Products Administration, NMPA）和美国食品药品监督管理局（Food and Drug Administration, FDA）批准上市的新药药物相互作用研究情况，旨在为我国药物研发过程中药物相互作用研究及其监管审评提供参考。     

微纳层叠聚丙烯腈凝胶流动特性的数值模拟研究

建立了层叠流道的三维模型和有限元网格模型，根据流变测试数据，采用Polymat对物料的黏度模型参数进行拟合，并利用Polyflow软件对聚丙烯腈（PAN）凝胶在层叠流道内的三维等温流动过程进行了数值模拟分析。研究发现，当入口流量增大时，层叠流道出口速度的不均匀性增加；沿流动方向流道内压力逐渐降低，并在出口处降低至同一最低值；流道进出口压力差与入口流量大小具有正相关性；在流道的中心截面上剪切速率分布均匀，波动较小。     

基于IEC 60870-5-104协议的调度命令发送方法研究

对IEC 60870-5-104协议的调度命令进行了研究，提出了一种基于现有IEC 60870-5-104协议的调度命令发送新方法。此技术充分利用了IEC 60870-5-104协议的文件发送功能，通过远程终端单元（RTU）向电厂发送包含调度命令的文本文件。考虑到调度命令在电力系统和电力市场结算系统安全方面的重要性，将该方法应用在电网调度自动化 SCADA 系统中，可以实现交换数据的更高可用性。     

煤矿罗茨鼓风机的安装使用与故障分析

对罗茨鼓风机的特点、结构和工作原理进行了论述,对其安装使用与故障维修进行了归纳总结.在新型罗茨鼓风机的设计中,提出了一种由偏心孤和圆线曲线组合的三叶转子齿剖面,其在对新齿轮廓进行几何模型的基础上,提出了螺旋齿轮廓,并对啮合螺旋三叶进行了比较研究.结果 表明,新的螺旋齿轮廓可以创造更大的气流,降低鼓风机压力的峰值.     

Performance of Al2O3 particle reinforced glass-based seals in planar solid oxide fuel cells

Glass-based materials are usually considered as excellent seals for jointing adjacent components in planar solid oxide fuel cells, but the uncontrollable crystallization in the glass may cause delamination and micro-cracks in such seals. To solve this problem, Al2O3 ceramic particles were added to a BaO–CaO–Al2O3–B2O3–SiO2 glass system to reduce negative effects caused by crystalline phase on the gas tightness and the joint strength in the seals. At an operating temperature of 750 °C, the glass-based seals with 20 wt% Al2O3 addition (GA80) exhibited extremely low leakage rates (~0.002 sccm/cm under an input gas pressure of 13.6 kPa) and higher shear strength (3.31 MPa). The Al2O3 ceramic addition and the crystalline phase BaAl2Si2O8 reinforced the glass matrix. Further thermal cycle analyses indicated that leakage rates for the GA80 seals remained at around 0.0025 sccm/cm after 10 thermal cycles, which was consistent with minor microstructural change and good interface bonding. Single cell testing with of GA80 seals was performed and the results demonstrated stable electrochemical performance through 6 thermal cycles at an open circuit voltage of 1.16–1.18 V, as well as a power density above 546 mW/cm2 at a current density of 925 mA/cm2. These results showed the high thermal cycle stability of the glass/Al2O3 composite seals in intermediate temperature planar solid oxide fuel cells.     

Enhanced thermal shrinkage behavior of phenolic-derived carbon aerogel-reinforced by HNTs with superior compressive strength performance

A novel carbon/m-HNTs composite aerogel was synthesized by introducing the modified halloysite nanotubes (m-HNTs) into phenolic (PR) aerogels through chemical grafting, followed with carbonization treatment. In order to explore the best proportion of HNTs to phenolic, the micromorphology of PR/m-HNTs were investigated by SEM before carbonization, confirming 10 wt% of m-HNTs is most beneficial to the porous network of aerogels. The interaction between PR and HNTs was studied by FTIR spectra, and microstructure evolution of the target product-carbon/m-HNTs composite aerogel were illustrated by SEM and TEM techniques. SEM patterns indicated that the carbon/m-HNTs aerogels maintain a stable porous structure at 1000 °C (carbonization temperature), while a ~20 nm carbon layer was formed around m-HNTs generating an integral unit through TEM analysis. Specific surface area and pore size distribution of composite aerogels were analyzed based on mercury intrusion porosimetry and N₂ adsorption–desorption method, the obtained results stayed around 500 m²g^?1 and 1.00 cm³g^?1 (pore volume) without significant discrepancy, compared with pure aerogel, showing the uniformity of pore size. The weight loss rate (26.76%) decreased greatly compared with pure aerogel, at the same time, the best volumetric shrinkage rate was only 30.83%, contributed by the existence of HNTs supporting the neighbor structure to avoid over-shrinking. The highest compressive strength reached to 4.43 MPa, while the data of pure aerogel was only 1.52 MPa, demonstrating the excellent mechanical property of carbon/m-HNTs aerogels.     

Turbulent boundary layer control with a spanwise array of DBD plasma actuators

The turbulent boundary layer control on NACA 0012 airfoil with Mach number ranging from 0.3 to 0.5 by a spanwise array of dielectric barrier discharge(DBD)plasma actuators by hot-film sensor technology is investigated.Due to temperature change mainly caused through heat produced along with plasma will lead to measurement error of shear stress measured by hot-film sensor,the correction method that takes account of the change measured by another sensor is used and works well.In order to achieve the value of shear stress change,we combine computational fluid dynamics computation with experiment to calibrate the hot-film sensor.To test the stability of the hot-film sensor,seven repeated measurements of shear stress at Ma = 0.3 are conducted and show that confidence interval of hot-film sensor measurement is from-0.18 to 0.18 Pa and the root mean square is 0.11 Pa giving a relative error 0.5％over all Mach numbers in this experiment.The research on the turbulent boundary layer control with DBD plasma actuators demonstrates that the control makes shear stress increase by about 6％over the three Mach numbers,which is thought to be reliable through comparing it with the relative error 0.5％,and the value is hardly affected by burst frequency and excitation voltage.     

50型螺旋式钢板仓卷边设备理论分析与试验

结合已有卷边设备的生产工艺和特点,研发了国内首台50型螺旋式钢板仓卷边设备,并完成了4次样机调试试验.分析了新型卷边设备关键机构的工作原理,对下轧辊调节机构进行了力学计算分析,完成了卷边孔型设计.利用显示动力学软件数值模拟了5 mm钢板的冷弯成形(卷边)过程,分析了成形过程中的等效应力和等效塑性应变.通过4次样机调试试验,将调试结果与模拟结果对比.结果 表明,折弯5 mm钢板比折弯3 mm的钢板力载荷大很多,有必要研发新型的卷边设备;卷边设备的后3个工位的应力峰值比前3个工位大,其中工位6应力峰值最大;文中的卷边孔型设计合理;卷边过程的模拟结果与试验结果一致.     

催化剂级配技术在加氢改质装置上的工业应用

基于柴油产品质量升级的需求,中国石化大连石油化工研究院(FRIPP)开发了FHIDW加氢改质技术及配套FF-46加氢精制催化剂、FC-14B加氢改质催化剂和FDW-3临氢降凝催化剂.该技术及催化剂级配体系在格尔木炼油厂0.8 Mt·a-1加氢改质装置上的工业应用情况表明,级配催化剂体系对原料适应性强,装置运转平稳,操作灵活性高,催化剂失活速率慢,产品分布合理且质量优异,在降低柴油产品凝点的同时可以明显改善其密度和十六烷值,解决了改造前装置生产重柴油密度偏低的问题,为炼油厂生产符合国V质量标准的柴油提供了技术保障.     

课程思政在现代学徒制煤化工专业课程中的教学探索——以"煤质分析及煤化工产品检验"课程为例

现代学徒制是一项深化产教融合、校企合作的育人机制,是创新技术技能人才的现代培养模式.山西铁道职业技术学院与山西安泰控股集团有限公司深度合作开展山西省现代学徒制试点项目,合作目的之一是培养企业煤化工专业人才.学校教师结合学生(员工)在企业车间岗位上的技能知识,系统地讲授煤化工专业课程"煤质分析及煤化工产品检验"理论知识,同时针对企业员工日常学习思想政治知识较少的实际,润物细无声地加入思政元素,实现专业知识与实践技能相结合,技能知识与思政教育相融合,真正培养知识型、技能型、创新型高素质技能人才,努力构建职业教育产业发展命运共同体.