5G NTN关键技术研究与演进展望

5G非地面网络（non-terrestrial network,NTN）技术是5G通信系统面向卫星通信和低空通信等新应用场景的重要技术，标志着5G技术应用从陆地通信走向了空间通信。首先分析了5G NTN和地面5G的差异点，包括网络架构、时频同步、HARQ和移动性管理等。进而介绍了3GPP Release 17的5G NTN标准进展及关键技术点与3GPP Release 18的5G NTN增强技术。最后展望了未来空、天、地一体化的技术演进。通过对5G NTN技术研究和标准分析，明确了5G和卫星通信融合的技术路线，并为后续6G空、天、地融合系统研究和设计提供基础。     

一种“KooN”结构的马尔可夫简并建模和简化计算的方法

IEC61508等标准提出了几种计算安全仪表系统需求时平均失效概率的方法,但是,对于具有冗余配置的复杂系统,随着组件数量的增加,系统的中间状态数量快速增长,用户难以构建马尔可夫模型,即便借助计算机来建模运算也较为耗时。提出了一种同型“K oo N”简并状态的马尔可夫建模的通用方法,首先是根据降级状态进行判断,将符合条件的状态进行简并,然后对标记为危险失效状态的概率进行计算。通过严格的理论推导,该简并状态方法可以在不损失精度的前提下简化马尔可夫建模。     

Effect of ultrasonic waveforms on gas–liquid mass transfer in microreactors

This study aims to investigate the effect of ultrasonic waveforms on the gas–liquid mass transfer process. For a given load power (P), continuous rectangular wave yielded stronger bubble oscillation and higher mass transfer coefficient (k_La) than continuous triangular and sinusoidal wave. For pulsed ultrasound, the k_La decreased monotonically with decreasing duty ratio (D), resulting in weak enhancement at low D (≤33%). For a given average load power (P_A), concentrating the P for a shorter period resulted in a higher k_La due to stronger cavitation behavior. For a given P_A and D, decreasing the pulse period (T) led to an increase in k_La, which reached a constant high level when the T fell below a critical value. By optimizing the D and T, a k_La equivalent to 92% of that under continuous ultrasound was obtained under pulsed ultrasound at a D of 67%, saving 33% in power consumption.     

Life cycle assessment of HFC-134a production by calcium carbide acetylene route in China

HFC-134a is a widely used environment-friendly refrigerant. At present, China is the largest producer of HFC-134a in the world. The production of HFC-134a in China mainly adopts the calcium carbide acetylene route. However, the production route has high resource and energy consumption and large waste emission, and few of the studies addressed on the environmental performance of its production process. This study quantified the environmental performance of HFC-134a production by calcium carbide route via carrying out a life cycle assessment (LCA) using the CML 2001 method. And uncertainty analysis by Monte-Carlo simulation was also carried out. The results showed that electricity had the most impact on the environment, followed by steam, hydrogen fluoride and chlorine, and the impact of direct CO₂ emissions in calcium carbide production stage on the global warming effect also could not be ignored. Therefore, the clean energy (e.g., wind, solar, biomass, and natural gas) was used to replace coal-based electricity and coal-fired steam in this study, showing considerable environmental benefits. At the same time, the use of advanced production technologies could also improve environmental benefits, and the environmental impact of the global warming category could be reduced by 4.1% via using CO₂ capture and purification technology. The Chinese database of HFC-134a production established in this study provides convenience for the relevant study of scholars. For the production of HFC-134a, this study helps to better identify the specific environmental hotspots and proposes useful ways to improve the environmental benefits.     

梯度铝蜂窝夹芯板的力学行为

梯度分层铝合金蜂窝板是一种有效的吸能结构,本工作在梯度铝蜂窝结构的基础上根据梯度率的概念,通过改变蜂窝芯层的胞壁长度,设计了4种质量相同、梯度率不同的铝蜂窝夹芯结构。通过准静态压缩实验,并结合非线性有限元模拟准静态及冲击态下梯度铝蜂窝夹芯结构的变形情况及其力学性能,分析对比了相同质量下梯度铝蜂窝夹芯结构在准静态下的变形模式以及冲击载荷下分层均质蜂窝结构和不同梯度率的分层梯度蜂窝结构的动态响应和能量吸收特性。结果表明:在准静态压缩过程中,铝蜂窝梯度夹芯板的变形具有明显的局部化特征,蜂窝芯的变形为低密度优先变形直至密实,层级之间的密实化应变差随芯层密度的增大而逐渐减小;在高速冲击下,梯度蜂窝板并非严格按照准静态过程中逐级变形直至密实,而是在锤头冲击惯性及芯层密度的相互作用下整体发生的线弹性变形、弹性屈曲、塑性坍塌及密实化;另外,在本工作所设计的梯度率中,当梯度率为γ₁=0.0276时,梯度蜂窝夹芯板的吸能性达到最好,相较于同等质量下的均质蜂窝夹芯板,能量吸收提高了10.63%。     

Influence of fluorine-containing side chain on the properties of waterborne polyurethane-urea

In order to prepare waterborne polyurethane with excellent water resistance and thermodynamic properties, a series of side chain fluorinated waterborne polyurethane-urea (FWPU-UA) was synthesized with polytetramethylene ether glycol, N-(2-methyl-1,3-propanediol-2′-)-perfluoro-1-butanesulfonyl amine (NPBA), isophorone diisocyanate, and isophoronediamine. With the increase of NPBA content, the weight loss temperature, glass transition temperature, and tensile strength of FWPU-UA were all improved. Gaussian fitting analysis of infrared data and density functional theory simulation proved that the introduction of fluorine side chains increased the interaction of hydrogen bonding in the FWPU-UA. X-ray photoelectron spectroscopy analysis indicated that the aggregation of fluorine atoms on the surface of film were caused by the migration and enrichment of fluorine side chains. Furthermore, the water resistance of polyurethane-urea film could be significantly improved by adding a small amount of NPBA, and the seven-day water absorption rate of polyurethane-urea film was reduced from 30.13% to 12.55%.     

Chromium-promoted preparation of forsterite refractory materials from ferronickel slag by microwave sintering

The chromium-promoted preparation of forsterite refractory materials from ferronickel slag was investigated by microwave sintering of the slag with the additions of sintered magnesia and 0–10 wt% chromium oxide (Cr₂O₃). The thermodynamic calculations revealed that the addition of Cr₂O₃ can promote the formations of spinel and liquid phase and maintain high content of forsterite below 1500 °C. The experimental results showed that there existed a stronger promoting effect of Cr₂O₃ additive on the properties of refractory materials in the microwave field than that in conventional sintering. It was attributed to the preferential formation and growth of spinel with stronger microwave absorption than other phases (e.g., enstatite), the existence of more forsterite, and the enhanced densification in association with the presence of more liquid phase at the same temperature. By microwave sintering of the mixture of ferronickel slag, 25 wt% sintered magnesia, and 4 wt% Cr₂O₃ at 1350 °C for 20 min, a superior refractory material with refractoriness of 1801 °C, thermal shock resistance of 6 times, bulk density of 2.97 g/cm³, apparent porosity of 1.4%, and compressive strength of 197 MPa was obtained. Compared with that prepared by conventional sintering at 1350 °C for 2 h, the refractoriness and thermal shock resistance were increased by 175 °C and 100%, respectively. The present study provided a novel method for preparing high-quality refractory materials from ferronickel slag and relevant industrial wastes.