Phenolic profiling reveals the metabolite basis of flesh colour and fresh-cut browning in apple fruit

Flesh colour, which is affected by cultivars and browning, can largely impact consumer acceptance in fresh-cut apples. The study profiled phenolic metabolites from apple flesh of twenty-three cultivars by widely targeted metabolomics. Comparison among white- and yellow-fleshed cultivars showed fifteen phenolics, mainly quercetin 3-O-glucoside, hyperoside, hesperetin 5-O-glucoside and cymaroside, in white-fleshed apples were significantly higher than those in yellow-fleshed apples. It may indicate a metabolite basis of yellow and white flesh colour, and better potential nutrition in white-fleshed apples. In addition, ten phenolic metabolites including five cyanidin glycosides showed significant differences between the highest and the lowest browning groups, indicating them may be crucial in browning of fresh-cut apple. This work elucidates the differences of phenolic profiles among apple cultivars with different flesh colour and provides useful data to evaluate the suitability of apple for fresh-cut processing.     

Lower down both ohmic and cathode polarization resistances of solid oxide fuel cell via hydrothermal modified gadolinia doped ceria barrier layer

Hydrothermal reaction in Cerium and Gadolinium solution as an optimization method is developed and first reported for the densification of gadolinia doped ceria, the barrier layer between Zirconia electrolyte and (La,Sr)(Co,Fe)O_3-δ cathode. This method is based on the hydrothermal reaction for nano particles in-situly grown on porous surface, to improve barrier layer density, alongside the sintering of cathode at 1075 °C. As a result, the ohmic resistance is prominently decreased by ～16.4 % at 750 °C for electrolyte supported symmetrical cell. Whereas, the cathode polarization resistance is decreased by as much as a factor of ～3 from 0.3702 Ω·cm² to 0.1325 Ω·cm² at 750 °C and $p_{O_2}=0.21atm$. Furthermore, the anode supported cell exhibits higher open circuit voltage, smaller area specific resistance, elevated performance output and less degradation. And this modified barrier layer shows reduced Sr migration in 300 h operation at 750 °C. The hydrothermal reaction is demonstrated to prepare denser and sintering-active barrier layer with faster oxygen ion transfer and better interface connection, with large-scale application prospects and cost-competitiveness.     

Chromium-promoted preparation of forsterite refractory materials from ferronickel slag by microwave sintering

The chromium-promoted preparation of forsterite refractory materials from ferronickel slag was investigated by microwave sintering of the slag with the additions of sintered magnesia and 0–10 wt% chromium oxide (Cr₂O₃). The thermodynamic calculations revealed that the addition of Cr₂O₃ can promote the formations of spinel and liquid phase and maintain high content of forsterite below 1500 °C. The experimental results showed that there existed a stronger promoting effect of Cr₂O₃ additive on the properties of refractory materials in the microwave field than that in conventional sintering. It was attributed to the preferential formation and growth of spinel with stronger microwave absorption than other phases (e.g., enstatite), the existence of more forsterite, and the enhanced densification in association with the presence of more liquid phase at the same temperature. By microwave sintering of the mixture of ferronickel slag, 25 wt% sintered magnesia, and 4 wt% Cr₂O₃ at 1350 °C for 20 min, a superior refractory material with refractoriness of 1801 °C, thermal shock resistance of 6 times, bulk density of 2.97 g/cm³, apparent porosity of 1.4%, and compressive strength of 197 MPa was obtained. Compared with that prepared by conventional sintering at 1350 °C for 2 h, the refractoriness and thermal shock resistance were increased by 175 °C and 100%, respectively. The present study provided a novel method for preparing high-quality refractory materials from ferronickel slag and relevant industrial wastes.     

Preparation and characterization of calcium phosphate cement with enhanced tissue adhesion for bone defect repair

Anti-washout and tissue adhesion properties are essential for the clinical application of injectable bone materials. In this study, we prepared calcium phosphate cement (CPC) with anti-washout and tissue adhesion properties and attempted to build covalent bonds between CPC and the amino groups in bone tissue under a self-regulating pH system in the CPC (acidic to basic). The results of push-out tests demonstrated that a significant enhancement (from 6.42 ± 0.76 N to 61.5 ± 4.09 N) in tissue adhesion was obtained with the addition of 6% (w/w) oxidized sodium alginate (OSA) in CPC. The FTIR, XRD, anti-washout test, XPS, pH test, and SEM results suggested that the synergistic effect of OSA-citric acid (CA) led to the formation of a three-dimensional gel network structure in the CPC, and the Schiff base reaction between aldehyde and amino groups induced adhesion between CPC and the bone tissue. Further, the addition of less OSA had no significant negative effect on the hydration properties of CPC. Our work aims to promote the development of injectable bone material in clinical applications.     

Bioinspired Triboelectric Soft Robot Driven by Mechanical Energy

A sustainable power source is a key technical challenge for practical applications of electrically responsive soft robots, especially the required voltage is over several thousand volts. Here, a practicable new technology, triboelectric soft robot (TESR) system with the primary characteristics of power source from mechanical energy, is developed. At its heart is TESR with bioinspired architectures made of soft-deformable body and two triboelectric adhesion feet, which is driven and accurately controlled through triboelectric effect, while reaching maximum crawling speeds of 14.9 mm s⁻¹ on the acrylic surface. The characteristics of the TESR, including displacement and force, are tested and simulated under the power of a rotary freestanding triboelectric nanogenerator (RF-TENG). Crawling of TESR is successfully realized on different materials surfaces and different angle slopes under the driven of RF-TENG. Furthermore, a real-time visual monitoring platform, in which TESR carries a micro camera to transmit images in a long narrow tunnel, is also achieved successfully, indicating that it can be used for fast diagnosis in an area inaccessible to human beings in the future. This study offers a new insight into the sustainable power source technologies suitable for electrically responsive soft robots and contributes to expanding the applicability of TENGs.     

Nitrogen Removal Performance of Denitrifying Ammonium Oxidation System in Treating Sulfamethoxazole-laden Secondary Wastewater Effluent

In this study,nitrogen removal performance of the denitrifying ammonium oxidation(DAO)process was investigated when treating sulfamethoxazole(SMX)-laden secondary wastewater effluent.The influent SMX concentration showed negligible effect on efficiencies for removal of nitrate and COD.However,the ammonium ions removal rate was moderately reduced,when the influent SMX concentration in wastewater reached 6 mg/L.Total nitrogen removal efficiency remained as high as 76.77%towards the day 158 at the end of experiment.Candidatus_Brocadia and Candidatus_Kuenenia were the functional anammox strains.The unclassified_f__Rhodobacteraceae sp.was predominant heterotrophic denitrifying strain in the studied reactor.The concentrations of soluble extracellular polymeric substances in sludge obviously increased from 16.76 mg/g VSS to 32.31 mg/g VSS,which might protect the nitrogen removal strains from high-concentration SMX.This result provides a theoretical and technical foundation for the application of denitrifying ammonium oxidation process in treating sulfamethoxazole-laden secondary wastewater effluent.     

四川某低品位金矿非氰浸出试验研究

对金品位为1.55 g/t的氧化矿采用非氰药剂进行浸金的工艺流程,考察了磨矿细度、药剂DZC浓度和浸出时间对金浸出率的影响。确定该金矿适宜的非氰浸出条件:磨矿细度-74μm含量占69.90%、石灰用量4 000g/t、矿浆液固比为2∶1、浸出药剂DZC浓度0.08%、浸出时间8 h,可获得金的浸出率为93.33%的良好指标。表明该氧化金矿在常温常压下,采用非氰浸出工艺是可行的。