超薄SiO2层的热生长

隧道小孔中超薄ＳｉＯ２的生长是ＥＥＰＲＯＭ电路制造的关键工艺之一。采用ＳＵＰＲＥＭ－Ⅲ工艺模拟程序对超薄ＳｉＯ２的热生长进行了工艺模拟，经过大量的工艺实验及优化，确定了超薄ＳｉＯ２的最佳生长条件，生长出的ＳｉＯ２性能良好，完全可满足ＥＥＰＲＯＭ研制的要求。     

Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

Call control and traffic transport for connection-oriented highspeed wireless personal communications over metropolitan area networks

A distributed circuit-switched approach for supporting the deployment of high speed wireless personal communication services in urban areas through the interconnection of base stations via metropolitan area networks (MANs) is proposed. Broadband MANs minimize traffic congestion by dynamic sharing of link capacity and by serving as distributed switches for partitioning call control functions. While the DQDB protocol readily supports distributed packet-switching over the IEEE 802.6 MAN, isochronous traffic such as voice and video is best supported by circuit-switched connections. The authors present an enhanced bi-state pre-arbitrated (PA) transport mechanism, and associated call control and handoff management techniques, which enable distributed circuit-switching over the MAN. These capabilities are not currently addressed in the 802.6 standards. The bi-state PA transport mechanism facilitates statistical multiplexing of variable rate isochronous traffic sources. The network capacity is constrained by the call setup delay performance, and is analyzed by simulations. Alternative signaling architectures, involving different placements of call control network elements, are evaluated. The effects of erasure nodes, and close bus versus open bus architectures, are considered. The overlap inter-MAN call setup procedure is proposed to reduce delays. Different call handoff procedures are formulated according to the type of handoff and the resulting change in call connectivity. Most handoffs are intra-MAN, requiring simple procedures with short delays     

陇上天路

如果说青藏铁路是一条“雪域天路”，那么宝鸡至天水高速公路就是一条“陇上天路”。宝鸡至天水是从关中平原到西北黄土高原的跨越地段，垂直跨度大，山连山，岭连岭，几乎看不到任何平原地段。作为2005年西部新开工的十大工程和交通部十二项示范工程之一，这条全长91公里的高速公路还要穿过甘肃屈指可数的林带，跨越黄河、长江两大流域，穿越甘肃最大的天然林保护基地--小陇山林业自然保护区、麦草沟自然保护区和麦积山国家森林公园。     

Variational principle of combined energy—Mechanics of laminated structures

The conventional approaches for stress analysis of composite laminates have encountered discontinuity problems. In this paper, the C¹ continuity of displacements in the in-plane directions and C⁰ continuity of displacement along the thickness direction are discussed. Also, the global continuity of transverse stresses and local continuity of in-plane stresses are examined. Then, the formulations of stress analysis in both differential equation form and variational functional form are presented.     

报业广告管理系统的设计与关键技术

基于集散式的数据库存储、三层软件架构、中间件、智能Agent、数据仓库及在线分析、图形图像处理等多项技术而开发的广告管理系统是报业营运的核心应用软件，是支撑报业取得经济效益的重要工具，文中重点阐述了其总体设计方案与关键技术。该系统在技术上的几项突破改变了报业传统生产方式，解决了多项长期困惑业界的难题，行业带动性强，已在实际应用中取得了显著的经济效益，具有在全国报业广泛推广的价值。     

提高E^2PROM中NMOS管源漏穿通电压的实验研究

为了提高Ｅ＾２ＰＲＯＭ中Ｎ管源漏穿通电压，用实验的方法对制造工艺进行了研究。结果表明，高能量注入是提高ＶＰＴ的有效手段，但受到ｐｎ结击穿的限制，只适用于低区短沟Ｎ管；ＤＤＤ工艺大幅度高ＶＰＴ，但ｐｎ结击穿电压低于２０Ｖ，不能应用于高压ＭＯＳ管；采用适量的防穿通注入和适当增大沟道长度为最理想的工艺途径。     

一种制做三维牙——颌骨光弹性模型的新方法

本文提出一种用“整体浇注法”制做三维牙——颌骨光弹性模型的新方法,即用价格便宜的石膏做阴模,先制出与真实牙几何相似的牙光弹性模型和模拟牙周膜的乳胶套,将它们粘接好,然后将其放入颌骨石膏阴模的适当位置,浇入环氧树脂混合液,用“二次固化法”进行固化,即可制成三维牙——颌骨整体光弹性模型。此法能保证模型与实物的严格几何相似和牙周的边界条件相似,使实验精度大大提高且工艺简单、成本低。