Real-Time analysis of exosome secretion of single cells with single molecule imaging

The exosome-mediated response can promote or restrain the diseases by regulating the intracellular pathways, making the exosome become an effective marker for diagnosis and therapeutic control at the single-cell level. However, real-time analysis is hard to be achieved with traditional approaches because the exosomes usually need to be enriched by ultracentrifugation for a measurable signal-to-noise ratio. Recently developed label-free single-molecule imaging approaches may become an real-time quantitative tool for the analysis of single exosomes and related secretion behaviors of single living cells owing to their extreme sensitivity.     

磁力可控电磁超声换能器设计及特性

电磁超声换能器一般采用具有超强磁力的稀土永磁制作,在实际检测中由于磁力不可控,存在偏置磁场不够强导致换能效率过低和磁力过强造成操作不方便等问题.提出一种偏置磁场磁力可控的电磁超声换能器,采用电磁铁与永磁铁相结合的方式,达到偏置磁场磁力可控的目的.通过有限元仿真和试验得出,提出的偏置磁场磁力可控的电磁超声换能器,在电磁铁处于关闭模式下,永磁铁能够提供基础磁场;采用增强模式或减弱模式,无被测物时,换能器下表面平均垂直磁通最大分别增强78.58％和减弱19.36％,而提离2 mm检测钢板时,换能器下方钢板表面平均垂直磁通最大分别增强52.99％和减弱38.02％;得出3种模式下,探头磁力随着提离距离缩小而增强的试验曲线;通过增强模式对铝板和钢板进行测厚试验,将检测信号幅值分别提高46.91％和62.01％.所设计的磁力可控电磁超声换能器不仅具有磁力可控的功能,还能够提高检测信号幅值.     

绝对式光电编码器的编码理论研究进展

介绍了用于角度测量的绝对式光电旋转编码器的编码理论研究概况,具体包括反射式格雷码、矩阵码、m序列码和单码道格雷码的绝对位置编码方法和编码特征。绝对位置编码的发展过程是以唯一性和单变性为基础特性,以单码道性为最终目标进行编码矩阵列数的缩减。目前,编码类型的发展经历了n条码道的反射式格雷码、n/3条码道矩阵码、2条码道的m序列码以及1条码道的单码道格雷码,已经达到单码道的最终目标。由于单码道格雷码编码理论尚不完善,仍依赖搜索获得编码,因此其快速构造方法是未来绝对位置编码理论的发展方向。最后,对近几年发展起来的基于图像传感器的非编码测量方法进行了介绍和展望,该方法是对传统测量方法的颠覆,有望成为光电式旋转编码器的另一个发展方向。     

某取排水车180°铰接式弯管优化分析

为了解决新型铰接式弯管的变形问题,利用ANSYS软件对铰接式弯管进行建模和流固耦合分析,发现原始弯管两侧中部内凹、弯径增大、最大应力超过许用应力,据此提出了导流器错位排布方案.结果 表明:采用方案三错位排布导流器方案、将导流器间距设为70 mm时得到最优方案,优化后的弯管4最大应力由178.12 MPa降低到92.4 MPa、降低了52％,弯管12最大应力由289.52 MPa降低到135.4 MPa、降低了47％,取得了较好的优化效果,为180°弯管导流器设计提供了一种新方案.     

刚性航天器的预定义时间滑模控制

针对刚性航天器在姿态跟踪控制中存在的系统不确定及外界干扰等问题,提出了一种预定义时间滑模控制器(PTSMC).首先,给出了以四元数为姿态参数的航天器姿态跟踪控制系统,利用误差四元数和误差角速度设计了预定义时间滑模面.然后,考虑了航天器系统的不确定性和外界干扰设计了一种非保守上界的PTSMC,并通过边界层技术降低了系统抖动.最后,通过设计Lyapunov函数,证明了所提出的控制器的预定义时间稳定性和系统收敛时间上界的非保守性.仿真结果表明,刚性航天器的姿态跟踪误差精度可达1.5×10-6 rad,角速度跟踪误差精度可达2×10-6 rad/s.与现有的预定义时间控制器相比,所提出的控制器的稳定时间上限是更加非保守的,与传统PD控制和非奇异终端滑模控制相比,所提出的控制器具有更高的跟踪精度和鲁棒性.通过3自由度气浮平台的姿态跟踪实验进一步说明了控制方案的有效性,其中角度跟踪误差小于0.1 rad,位置跟踪误差小于0.2 m.     

平行坐标技术在干式变压器温度场可视化分析中的应用

本文中笔者将平行坐标技术应用于变压器温度场多维可视化分析,以矿用变压器为例,给出了其高、低压绕组纵向温度分布.     

高稳高效海上风电安装平台关键制造技术研究

海上风电作为可再生清洁能源之一,受到世界各国的高度重视与大力发展。我国将海上风电提升至解决能源危机、减缓气候变化、调整能源结构的国家战略高度,到2030年我国单位国内生产总值二氧化碳排放将比2005年下降65%以上,非化石能源占一次能源消费比重将达到25%左右。安装平台不足将是我国海上风电场无法如期建成投产的主要障碍。对自升自航式海上风电安装平台系列高端装备及其设计制造的三大技术难题——腿站立作业易“失稳”、大平台大跨距大倾覆力矩自升易“失控”、高空吊装巨型叶片逾百螺栓精准定位易“失准”,以及焊缝缺陷修复和局部裂纹损伤的激光锻造修复再制造进行了介绍,研制的具有不同规格的系列装备在中国、英国、丹麦、德国等国家的著名海上风电场建设应用情况良好。     

Effect of phosphogypsum on saline-alkalinity and aggregate stability of bauxite residue

A column experiment was conducted to investigate the effect of phosphogypsum (PG) on the saline- alkalinity, and aggregate stability of bauxite residue. Results showed that: with increasing leaching time, the concentrations of saline-alkali ions decreased while the concentration increased in bauxite residue leachate; compared with CK (control group) treatment, pH, electric conductivity (EC), exchangeable sodium percentage (ESP), sodium absorption ratio (SAR), and exchangeable Na⁺ content of bauxite residue were reduced following PG treatment; average particle sizes in aggregates following CK and PG treatments were determined to be 155 and 193 nm, respectively. SR-μCT test results also confirmed that bauxite residue following PG treatment acquired larger aggregates and larger pore diameter. These results indicate that the PG treatment could significantly modulate the saline-alkalinity, and simultaneously enhance aggregate stability of bauxite residue, which provides a facile approach to reclaim bauxite residue disposal areas.     

Superhydrophobic aluminum alloy surface with excellent universality,corrosion resistance,and antifouling performance prepared without prepolishing

It is urgently necessary to seek more simple and effective methods to construct superhydrophobic metal surfaces to improve the corrosion resistance and antifouling performance. Herein, a facile method for fabricating superhydrophobic aluminum alloy surface is developed via boiling water treatment and stearic acid modification. It is noteworthy that no prepolishing on aluminum alloy is required and no caustic reagents and typical equipments are used during the preparation procedure. Therefore, the fabrication method is quite a simple and environment-friendly technique. Both micro- and nano-scaled binary structure forms at the resultant aluminum alloy surface while long alkyl chains are grafted onto the rough aluminum alloy surface chemically. Consequently, the resultant aluminum alloy exhibits outstanding superhydrophobicity. More importantly, the superhydrophobicity has excellent universality, diversity, stability, excellent corrosion resistance, and antifouling performance. The facile preparation, excellent superhydrophobic durability, and outstanding performance are quite in favor of the practical application.     

Agronomic performance of high oleic,low linolenic soybean in Tennessee

Soybean oil hydrogenation alters the linolenic acid molecule to prevent the oil from becoming rancid, however, health reports have indicated trans-fat caused by hydrogenation, is not generally regarded as safe. Typical soybeans contain approximately 80 g kg⁻¹ to 120 g kg⁻¹ linolenic acid and 240 g kg⁻¹ of oleic acid. In an effort to accommodate the need for high-quality oil, the United Soybean Board introduced an industry standard for a high oleic acid greater than 750 g kg⁻¹ and linolenic acid less than 30 g kg⁻¹ oil. By combing mutations in the soybean plant at four loci, FAD2-1A and FAD2-1B, oleate desaturase genes and FAD3A and FAD3C, linoleate desaturase genes, and seed oil will not require hydrogenation to prevent oxidation and produce high-quality oil. In 2017 and 2018, a study comparing four near-isogenic lines across multiple Tennessee locations was performed to identify agronomic traits associated with mutations in FAD3A and FAD3C loci, while holding FAD2-1A and FAD2-1B constant in the mutant (high oleic) state. Soybean lines were assessed for yield and oil quality based on mutations at FAD2-1 and FAD3 loci. Variations of wild-type and mutant genotypes were compared at FAD3A and FAD3C loci. Analysis using a generalized linear mixed model in SAS 9.4, indicated no yield drag or other negative agronomic traits associated with the high oleic and low linolenic acid genotype. All four mutations of fad2-1A, fad2-1B, fad3A, and fad3C were determined as necessary to produce a soybean with the new industry standard (>750 g kg⁻¹ oleic and <30 g kg⁻¹ linolenic acid) in a maturity group-IV-Late cultivar for Tennessee growers.