Influence of selenium growth condition on the photovoltaic conversion efficiency of Sb2Se3 as the solar cell absorption layer

Journal of Materials Science: Materials in Electronics - The influences of the selenium (Se) growth condition on the electronic level structure including deep defects and further on the...     

Co-precipitation synthesis of ZnAl2O4: Cr3+ phosphor for better light penetration in pc-LED

Cr doped ZnAl₂O₄ spinel samples were prepared by the traditional solid state reaction and co-precipitation synthetic route, and the results suggest that the co-precipitation method has some superiority in contrast to the solid state reaction method. XRD, FT-IR, and XPS spectra confirmed that the well-crystallized spinel cubic phase of ZnAl₂O₄: Cr³⁺ samples were successfully formed. The morphology of the samples was investigated by FE-SEM and FE-TEM, and the results show that the samples by the co-precipitation route can generate a smaller size of particles compared to the solid state reaction. Photoluminescence excitation spectra monitored at 686 nm are comprised of two broad excitation bands near 530 nm and 395 nm, and the emission spectra show emissions ranging from 640 to 780 nm, due to the ²E?→?⁴A₂ spin-forbidden transition of Cr³⁺ ions in spinel lattices. The optimized concentration monitored at 686 nm is 1%, while at 693 nm is 3.5%. Compared with the samples by solid state reaction method, the samples by co-precipitation method show preferable luminescent properties, such as the higher photoluminescence intensity and higher quantum efficiency. Several phosphor-converted LEDs were to investigate the applicability of the prepared samples. The results confirm that the phosphor has potential applications in plant growth and supplementing the red region in white-LEDs and the phosphors prepared by co-precipitation are more suitable to be used in phosphor-converted LED devices due to their preferable luminescent properties.

     

离子型稀土矿山淋洗及尾水富集试验研究

对浸矿后离子型稀土原地浸矿场采用清水进行淋洗，在184天的清水淋洗过程中，尾水氨氮值从最开始的507mg/L，降低至140mg/L，淋洗尾水pH4.52~3.10。淋洗尾水采用两级反渗透膜分离，既回收有价资源稀土，又能使出水氨氮达标。结果表明，产水氨氮浓度稳定低于15mg/L，对稀土的截留率高于98.25%，浓水中稀土离子平均浓度313.4mg/L，可进一步回收稀土资源。     

双酚芴环氧树脂体系热性能和粘接性能研究

环氧树脂是一种性能优异的热固性树脂，在结构胶粘剂和纤维增强复合材料领域应用广泛。但是常见的环氧树脂体系耐热性普遍较差，近年来，航空航天领域对材料的热性能提出了更高的要求，常规的环氧树脂体系已经无法满足耐高温需求。针对该问题，我们设计了一种耐热性较高的双酚芴型环氧树脂体系，并对其热性能和粘接性能进行了研究。在本文中，首先采用流变学方法和DSC研究了其工艺性能，使用DMA和TGA法分析了环氧树脂体系的耐热性能，并通过单搭接剪切试验测试了该环氧体系的粘接性能。结果表明，双酚芴型环氧树脂体系可在180℃固化，固化后的玻璃化转变温度达到190℃，失重5%时的温度为392℃，150℃时的剪切强度为5.8 MPa，展现了优异的耐热性能和粘接性能。     

基于电信号特征分析的电机故障诊断技术

介绍了电机故障诊断技术平台的组成,分析了电机常见故障下电信号的特征。利用宜昌和景洪工厂两台电机进行了实际对比测试,宜昌工厂电机定子电流特征频率在49.2Hz时表现出峰值-36.08dB,在50.8Hz时表现峰值则为-37.23dB,表明电机存在转子断条故障;景洪工厂电机在转子特征频率为113.51Hz时,出现峰值-58.47dB,表明电机存在静态偏心故障。经电机现场抽芯检查,验证了电机故障快速诊断平台给出的电机健康状态评估结果,证实了基于电信号特征分析的电机故障诊断技术的准确性。     

基于超声导波SC-DTW的金属板微损检测方法

针对金属板材的质量控制与服役性能评估问题,在对金属板材微损伤进行超声导波检测的基础上,结合形状上下文(shape context,SC)与动态时间规整方法对其损伤劣化程度进行量化评估.该方法以无损Lamb波信号为基准,采用动态时间规划(dynamic time warping,DWT)算法对损伤信号进行相似匹配分析对比,确定基准信号与损伤信号的最佳匹配路径.引入SC的轮廓识别方法对Lamb波的局部波形信息进行统计分析,以波形形状距离代替传统欧氏距离匹配方法,解决DTW相似匹配中的病态对齐问题.最后,将无损Lamb波与损伤Lamb波信号间SC-DTW匹配距离作为损伤程度的量化指标,采用随机闭合裂纹的有限元仿真模型和铝板弯折实验对所提出方法进行验证,结果表明,基于Lamb波SC-DTW的损伤量化指数对铝板早期裂纹具有较高的敏感性和较好的量化表征能力.该方法无需对波包进行识别,也不必进行复杂的特征提取,具有简单高效和抗噪声能力强等优点,在金属板服役性能评估与质量控制中有较好的实用性和推广价值.     

一种直升机避障电力线检测方法

电力线是一类形状细长、特征稀疏、随着视角的变化容易混淆在大量背景信息中的特殊障碍物，常规电力线检测识别算法得到的目标框对电力线所在位置的估计不够准确。为此，提出了一种相对角度估计方法，基于常规电力线目标检测与识别算法，并结合电力线相对角度估计，从而提高电力线的检测识别过程中所在位置的精度。相比电力线绝对角度回归的方法，提出的相对角度估计方法容易训练易收敛，计算量小，适用于实时性要求较高的应用场合。