NNI-1型C_5/C_6烷烃异构化催化剂长周期运行分析及建议

中国石化海南炼油化工有限公司0.2 Mt/a C5/C6烷烃异构化装置以连续重整装置的拔头油为原料,使用NNI-1催化剂,采用一次通过流程,不设脱异戊烷塔和稳定塔,经设在连续重整装置内的脱丁烷塔稳定处理后作为汽油调合组分。该装置于2006年9月开工投产,截至2015年3月已连续运行3个周期。长周期运行分析结果表明:前两个周期中NNI-1催化剂具有较高的异构化活性及选择性,C5异构化率为60%左右,C6异构化率为80%左右,C6选择性为15%左右,产品辛烷值基本达到技术指标要求(RON≥78);而在第三周期运行中,催化剂积炭增加等原因导致其异构化活性及选择性降低,异构化产品辛烷值提升能力呈现逐步衰减的趋势,提高反应苛刻度已不能弥补催化剂活性下降造成的产品辛烷值降低。为保证装置长周期运行,建议择机停工对催化剂进行再生,或是直接换用与装置原料性质匹配的异构化催化剂。     

Longitudinal permeability determination of dual-scale fibrous materials

In this work, the longitudinal permeability of squarely packed dual-scale fiber preforms is studied theoretically. These fiber preforms are composed of aligned porous tows and the tows are tightly packed. The effective permeability is calculated as a parallel-like network of intra-tow permeability and inter-tow permeability, which are quantified by Darcy’s law and the inscribed radius between tows, respectively. The jump velocity at the interface between inter-tow fluids and porous tows is considered, as derived by substituting Beavers and Joseph’s correlation into Brinkman’s equation. We further examine the effects of intra-tow permeability on the effective permeability of the fibrous system with three interface conditions: (1) interface velocity = 0, (2) interface velocity = mean intra-tow velocity, and (3) interface velocity = jump velocity. The jump-velocity-based model is found to be closest to numerical data. The influence of the fiber volume fraction of tows on the effective permeability is also analyzed.     

Mathematical modeling of growth of Salmonella spp. and spoilage microorganisms in raw oysters

The main objective of this study was to develop the primary and secondary models to describe the growth kinetics of Salmonella as well as background microorganisms in raw, shucked oysters. Samples, inoculated with a cocktail of two Salmonella serotypes, S. Typhimurium (CICC22956) and S. Enteritidis (CICC21482), were incubated at 4, 8, 12, 16, 20, 25, 30, 33, 37, 40, and 43 °C. Growth of Salmonella was observed at all temperatures, except at 4 °C. The background microorganisms grew at all temperatures. All growth curves clearly exhibited lag, exponential and stationary phases, and were analyzed using the Huang growth model. Three secondary models (Ratkowsky square-root, Huang square-root, and Cardinal parameter models) were compared for evaluating the effect of temperature on bacterial growth rates. Data analysis was performed using IPMP 2013, a free predictive microbiology software tool developed by the USDA ARS.The Cardinal parameters model underestimated the specific rates of the microorganisms at low temperatures. The Huang square-root model was more suitable than the Ratkowsky square-root model for describing the effect of temperature on growth of Salmonella, while the Ratkowsky square-root model, on the other hand, was more suitable for background microorganisms. For both Salmonella and background microorganisms, the logarithms of the lag phase were expressed as linear functions of the logarithms of specific growth rates. The results of this study can be used by the food retailers and regulatory agencies to estimate the microbial shelf-life of raw, shucked oysters.     

Analysis of adhesively bonded CFRE composite scarf joints modified with MWCNTs

The main objective of the present work is to improve the performance of bonded joints in carbon fiber composite structures through introducing Multi-Walled Carbon Nanotubes (MWCNTs) into Epocast 50-A1/946 epoxy, which was primarily developed for joining and repairing of composite aircraft structures. Results from tension characterizations of structural adhesive joints (SAJs) with different scarf angles (5–45°) showed improvement up to 40% compared to neat epoxy (NE)–SAJs. Special attention was considered to investigate the performance of SAJs with 5° scarf angle under different environments. The tensile strength and stiffness of both NE-SAJs and MWCNT/E-SAJs were dramatically decreased at elevated temperature. Water absorption showed a marginal drop of about 2.0% in the tensile strength of the moist SAJs compared to the dry one. Cracks initiation and propagation were detected effectively using instrumented-SAJs with eight strain gauges. The experimental results agree well with the predicted using three-dimensional finite element analysis model.     

Stochastic free vibration analyses of composite shallow doubly curved shells – A Kriging model approach

This paper presents the Kriging model approach for stochastic free vibration analysis of composite shallow doubly curved shells. The finite element formulation is carried out considering rotary inertia and transverse shear deformation based on Mindlin’s theory. The stochastic natural frequencies are expressed in terms of Kriging surrogate models. The influence of random variation of different input parameters on the output natural frequencies is addressed. The sampling size and computational cost is reduced by employing the present method compared to direct Monte Carlo simulation. The convergence studies and error analysis are carried out to ensure the accuracy of present approach. The stochastic mode shapes and frequency response function are also depicted for a typical laminate configuration. Statistical analysis is presented to illustrate the results using Kriging model and its performance.     

云杉八齿小蠹Ips typographus L.虚拟模型构建方法研究

本文以云杉八齿小蠹Ips typographus Linnaeus为例,经标本选取,观察虫体整体形态,绘制整体结构草图,电子显微镜观察局部、得到局部数字图像,分别建立虫体每一部分的高精度细节。把模型每部分拼装在一起组成整体模型,构建出了云杉八齿小蠹三维虚拟昆虫数字化模型。     

Piezoresistive in-situ strain sensing of composite laminate structures

Various methods have been developed to monitor the health and strain state of carbon fiber reinforced polymers, each with a unique set of pros and cons. This research assesses the use of piezoresistive sensors for in situ strain measurement of carbon fiber and other composite structures in multidirectional laminates. The piezoresistive sensor material and the embedded circuitry are both evaluated. For the piezoresistive sensor, a conductive nickel nanocomposite sensor is compared with the piezoresistivity of the carbon fiber itself. For the circuit, the use of carbon fibers already present in the structure is compared with the use of nickel coated carbon fiber. Successful localized strain sensing is demonstrated for several sensor and circuitry configurations. Numerous engineering applications are possible in the ever-growing field of carbon-composites.     

Microwave assisted-in situ synthesis of porous titanium/calcium phosphate composites and their in vitro apatite-forming capability

Microwave irradiation has been proven to be an effective heating source in synthetic chemistry, and can accelerate the reaction rate, provide more uniform heating and help in developing better synthetic routes for the fabrication of bone-grafting implant materials. In this study, a new technique, which comprises microwave heating and powder metallurgy for in situ synthesis of Ti/CaP composites by using Ti powders, calcium carbonate (CaCO₃) powders and dicalcium phosphate dihydrate (CaHPO₄·2H₂O) powders, has been developed. Three different compositions of Ti:CaCO₃:CaHPO₄·2H₂O powdered mixture were employed to investigate the effect of the starting atomic ratio of the CaCO₃ to CaHPO₄·2H₂O on the phase, microstructural formation and compressive properties of the microwave synthesized composites. When the starting atomic ratio reaches 1.67, composites containing mainly alpha-titanium (α-Ti), hydroxyapatite (HA), beta-tricalcium phosphate (β-TCP) and calcium titanate (CaTiO₃) with porosity of 26%, pore size up to 152 μm, compressive strength of 212 MPa and compressive modulus of 12 GPa were formed. The in vitro apatite-forming capability of the composite was evaluated by immersing the composite into a simulated body fluid (SBF) for up to 14 days. The results showed that biodissolution occurred, followed by apatite precipitation after immersion in the SBF, suggesting that the composites are suitable for bone implant applications as apatite is an essential intermediate layer for bone cells attachment. The quantity and size of the apatite globules increased over the immersion time. After 14 days of immersion, the composite surface was fully covered by an apatite layer with a Ca/P atomic ratio approximately of 1.68, which is similar to the bone-like apatite appearing in human hard tissue. The results suggested that the microwave assisted-in situ synthesis technique can be used as an alternative to traditional powder metallurgy for the fabrication of Ti/CaP biocomposites.     

Reduction of waste biosolids by RAS-ozonation: Model validation and sensitivity analysis for biosolids reduction and nitrification

Biosolids reduction model by return activated sludge ozonation was validated by simulating nitrification data compiled from our pilot-scale and the literature studies. Then, a global sensitivity analysis (GSA) was performed to identify influential and non-influential parameters for biosolids reduction efficiency, change in specific nitrification activity (SNA), and alteration to expected nitrification stability. In general, the model outputs were sensitive to operational and ozone reaction parameters, but not to biochemical parameters. For operational parameters, mainly temperature and initial solids retention time (SRT) influenced all model outputs. For biosolids reduction, increase in the degradability of the influent COD decreased the reduction efficiency. For SNA, the changes were highly dependent on the influent TKN/COD ratio. Our findings also imply that the stability of the nitrification process in ozonated systems should be enhanced at constant MLVSS for warm temperatures, but could be reduced at temperatures below 12 °C and aerated SRTs below 10 days.