A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

串行及并行A/D转换器在高速数据采集中的采样差别性分析

串行和并行接口模式是A/D转换器诸多分类中的一种,但却是应用中器件选择的一个重要指标.在同样的转换分辨率及转换速度的前提下,不同的接口方式不但影响了电路结构,更重要的是将在高速数据采集的过程中对采样周期产生较大影响.本文通过12位串行ADC ADS7822和并行ADC ADS774与AT89C51的接口电路,给出二者采样时间的差异性.     

CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

Σ-ΔA/D转换技术及仿真

Σ－ΔＡ／Ｄ转换技术近年来颇受重视，因为基于该技术的Ａ／Ｄ转换器能达到很高的分辨率（１６ｂｉｔ以上），并另具一系列优点。本文对Σ－ΔＡ／Ｄ转换器的基本原理，包括过采样（Ｏｖｅｒｓａｍｐｌｉｎｇ），噪声成形（ＮｏｉｓｅＳｈａｐｉｎｇ），以及数字抽取滤波（ＤｉｇｉｔａｌＤｅｃｉｍａｔｉｏｎＦｉｌｔｅｒｉｎｇ）等内容，均作了叙述。作者还对一个２０ｂｉｔΣ－Δ转换器的算法进行了计算机仿真。该转换器采用了高阶ＭＡＳＨ噪声成形技术，而其数字抽取滤波部分则由梳状滤波器与级联的半带滤波器构成。文章中给出了仿真结果。     

利用新型场效应管(QFET)的正向变换器

介绍了单端正向变换器基本电路，重点叙述带三路调节DC电压的100KHZ180W离线电源。它采用具有低导电阻RDS和低栅极电荷Qg的新型场效应管（QFET）作为变换电路的主开关器件，降低了电源开关损耗并提高了效率3%-5%。     

Corrosion Inhibition Mechanism with Spilt Cell Technique of Rare Earth Metal on LC4 Al Alloy

A new method of studying the corrosion inhibition mechanism of rare earth metal(REM) on LC4 Al alloy with the spilt cell technique was studied. The principle and experimental method of the spilt cell technique were analyzed. By measuring the change of net-electric current between the two electrodes caused by the change of the amount of oxygen in the solution and the addition of CeCl₃, the influence of corrosive performance of CeCl₃ on LC4 super-power aluminum alloy in the 0.1 mol·L⁻¹ NaCl solution was investigated. Meanwhile, the conditional changes of pH values, CeCl₃ solution, additire and time of performance were also studied. Finally, the features of electrode surface were revealed by using SEM and X-ray energy-dispersive spectrometry (EDS). By combining these with other electric chemical techniques, such as potential-time curve, polarization curve et al.     

辽河催化裂化澄清油中间馏分热反应研究

采用先加入絮凝剂脱灰，再经减压蒸馏切割420～500℃馏分的方法，将辽河催化裂化澄清油预处理，考察了澄清油、加入絮凝剂脱灰后的澄清油以及脱灰后再减压蒸馏所得的中间馏分这3种原料在热转化过程中中间相的转化历程，并采用偏光显微镜观察热转化产物。结果表明，澄清油预处理效果明显，所得中间馏分具有较低的H／C原子比（nH／nC）和适宜的组成分布，是生产针状焦的理想原料。热转化产物的光学组织结构属于各向异性发达的广域-流线型结构。     

Cure reaction for modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide

The glass‐transition temperature as a function of curing conversion for a modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide (BMI) resin was investigated at different temperature regimes and modeled using a modified Di Benedetto equation. Although the relationship between the glass‐transition temperature and conversion of the BMI system conforms to the Di Benedetto equation for α < 0.6 and at lower cure temperatures, at higher cure temperatures the results deviated significantly from the equation; thus, it was an inadequate model for the system. Fourier transform IR analysis showed that the major crosslinking reactions did not occur during cure for the modified BMI at and below 150°C. However, as the cure temperature was increased, the crosslinking reactions responsible for 3‐dimensional network structures became more dominant. At 190°C the C? N? C_stretch vibration of the uncured maleimide ring converted into succinimide rings in the curing process. Simultaneously, a decrease was observed for the absorbance bands of ? C? H_bending (maleimide). The higher cure temperatures induced a significantly faster initial crosslinking rate and also resulted in a shorter period of time after which further crosslinking was retarded, because the increase in the crosslinks also physically slowed further crosslinking activity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 227–235, 2002     

VSP旅行时反演应用于VSP—CDP转换

非零偏移距垂直地震剖面(VSP)模型的制作是非零偏移距VSP资料处理的关键环节之一,是VSP-CDP转换的基础。本文试用旅行时反演修正非零偏移距VSP的模型,以加速模型的制作过程,提高非零偏移距VSP的处理速度。用合成VSP资料试算表明:旅行时的随机误差对模型的制作影响不大;只要能较准确地确定界面位置,用旅行时反演修改制作非零偏移VSP模型是可行的。本文还探讨了初始模型的不同选择方法,并将旅行时反演用于实际VSP资料的处理。结果表明,大大地节省了非零偏移距VSP资料的处理时间。