控制爆破法处理卡钻事故

介绍了在包头市某工程实施管道穿越黄河施工中,采用爆破法处理卡钻的经验。针对深水环境条件及钻杆内径小不宜采用集团装药的条件,确定采用"小直径爆破筒,钻杆内部装药"的爆破方案,阐述了爆破设计及施工注意事项。可供类似工程参考。     

Dynamic simulation of hydrogen-based off-grid zero energy buildings with hydrogen storage considering Fanger model thermal comfort

In this study, some locations with different climates, off-grid zero energy buildings with hydrogen energy storage systems are designed, and transient analysis is conducted. These considered buildings supply their electricity consumption without using the electrical grid and PV panels or wind turbines. Also, they supply thermal comfort to occupants by using a vapor compression chiller and humidifier. Domestic hot water of occupants is supplied using solar collectors. For analyzing building's performance and objectives achievement, TRNSYS software is used. Also, for evaluating occupant thermal comfort, the Fanger model is used. The considered building is a one-story building with a 150 m² area. Four occupants are considered. Both of them are seated at rest, and another is seated with light working such as typing. Using the Fanger model equation and MATLAB software, the thermal comfort of occupants is determined. For domestic hot water consumption, verified profiles that vary during 24 h of the day are considered. Achieved results show that for humid and cold cities, PV panels with an area of 73 and 76 m² can be supplied the required electricity of considered building with four occupants and battery state of charge is higher than 50% and 10%, respectively. Moreover, with a suitable air conditioner system, the predicted percentage of dissatisfied (PPD) can be lower than 12% and 8% for humid and cold cities. Therefore, the building can be converted to a zero-energy building using its rooftop area.     

Effects of different metal corrosion inhibitors on hydrogen suppression and film formation with Mg–Zn alloy dust in NaCl solutions

To improve the safety of wet dust removal systems for processing magnesium-based alloys, a new method is proposed for preventing hydrogen generation. In this paper, hydrogen generation by Mg–Zn alloy dust was inhibited with six common metal corrosion inhibitors. The results showed that sodium dodecylbenzene sulfonate was the best hydrogen inhibitor, while CeCl₃ enhanced hydrogen precipitation. The film-forming stability of sodium dodecylbenzene sulfonate was tested with different contents, temperatures, Cl^? concentrations and perturbation rates. The results showed that this inhibitor formed stable protective films on the surfaces of Mg–Zn alloy particles, and adsorption followed the Langmuir adsorption model.     

Status and initial experiments of DRAGON-V facility for lithium-lead blanket technologies of hydrogen fusion reactors

A dual-coolant integrated experimental facility named DRAGON-V has been developed at the Institute of Nuclear Energy Safety Technology, Hefei Institute of Physical Science, Chinese Academy of Sciences, for the key technology research and performance evaluation of candidate liquid lithium-lead (PbLi) blanket of hydrogen fusion reactors. The loop is composed of a material test sub-loop and thermal-hydraulic test sub-loop, the design parameters are PbLi inventory 20 tons, PbLi temperature up to 550 °C, the maximum PbLi flow rate up to 40 kg/s. A novel cold trap system is designed to remove the suspended and crystalized impurities in PbLi fluid with three cooling zones and cross row arrangement of rod bundle filter elements. The paper describes the loop itself and its major components, initial loop testing, flow and measurement diagnostics and current experiments. The obtained test results of the loop and its components have demonstrated that the new facility is fully functioning and ready for experimental studies of material corrosion with/without a magnetic field, magnetohydrodynamic (MHD) effect, purification, heat and mass transfer phenomena in PbLi flows and can also be used in mock-up testing in conditions relevant to fusion applications.     

Combining a new baseboard radiator with a fan coil system for improving heating performance and reduce energy consumption

In the present work, the heating performance of a new system combined with a new modified baseboard radiator and fan coil is investigated. Using longitudinal fins with special geometry and also forced airflow at the end of the system causes that at the lower inlet water temperature compared with the conventional models, higher heat output rate be obtained. The heat output rate of the new modified system is obtained by experimental metrology based on the European Standard No. EN-442. Temperature and velocity distribution in the room space is done by simulation of the modified system in the Flovent software. Computational fluid dynamics (CFD) results are validated against experimental results and there is a good agreement between them. Also, the energy consumption of the system during the winter season is calculated in TRANSYS software. Experimental results show that the heat output rate of a new modified heating system with inlet water temperature in the range of 45–55°C is on average 4.17 times higher compared with the conventional model. CFD simulation also showed that the combined system provides good thermal comfort conditions. Energy consumption of the new system reduced about 13% compared with conventional models.     

“半翻转”教学模式下评价指标体系研究与实践

研究基于“半翻转”教学模式的线上教学评价指标体系,包括课前活动开展、课中教学活动设计、课后任务以及基于此过程中的评价指标体系设计。最后通过层次分析法设计评价指标权重,设计评价算法得到动态评价结果。该评价指标体系应用在本专业“数据结构与算法”课程中,并得到良好的应用效果。     

Direct ink writing of vancomycin-loaded polycaprolactone/ polyethylene oxide/ hydroxyapatite 3D scaffolds

Novel inks were formulated by dissolving polycaprolactone (PCL), a hydrophobic polymer, in organic solvent systems; polyethylene oxide (PEO) was incorporated to extend the range of hydrophilicity of the system. Hydroxyapatite (HAp) with a weight ratio of 55–85% was added to the polymer-based solution to mimic the material composition of natural bone tissue. The direct ink writing (DIW) technique was applied to extrude the formulated inks to fabricate the predesigned tissue scaffold structures; the influence of HAp concentration was investigated. The results indicate that in comparison to other inks containing HAp (55%, 75%, and 85%w/w), the ink containing 65% w/w HAp had faster ink recovery behavior; the fabricated scaffold had a rougher surface as well as better mechanical properties and wettability. It is noted that the 65% w/w HAp concentration is similar to the inorganic composition of natural bone tissue. The elastic modulus values of PCL/PEO/HAp scaffolds were in the range of 4–12 MPa; the values were dependent on the HAp concentration. Furthermore, vancomycin as a model drug was successfully encapsulated in the PCL/PEO/HAp composite scaffold for drug release applications. This paper presents novel drug-loaded PCL/PEO/HAp inks for 3D scaffold fabrication using the DIW printing technique for potential bone scaffold applications.     

“数字信号处理”课程的几何视角

“数字信号处理”的经典课程体系以“系统”为中心，以离散时间傅立叶变换、z变换和离散傅立叶变换为分析工具，以滤波器设计为目的，注重定理和公式推导及其性质分析，很难让学生建立一个形象的、完整统一的知识体系框架。本文从几何视角将 “系统”化和“代数”化的经典课程体系重构为面向“信号”的“几何”知识体系，从而提升学生对本质问题的“洞察力”，帮助学生建立系统的知识体系。     

传统企业数字化转型能力体系构建研究

企业试图完成数字化转型,这是在竞争中谋求发展的必经之路。文章率先进行数字化转型特征、策略的概念分析,而后总结以此为背景的能力模型、企业管理能力与技术能力,最终以某公司案例完成体系构建与应用的阐述。     

我国水-能源-粮食耦合关系及影响因素

为缓解我国水、能源和粮食资源紧张问题，促进资源可持续利用，构建水-能源-粮食系统，利用耦合协调度模型对我国的30个省（自治区、直辖市）进行测算,并利用空间杜宾模型分析主要影响因素。结果表明：2003—2017年，我国能源、粮食评价[JP]指数高于水资源评价指数，系统综合评价指数逐年递增；大部分省份耦合协调度处于初级协调水平且呈现逐年上升的态势，个别省份耦合协调度濒临失调；耦合协调度空间自相关性较强，虽有明显波动，但是呈现逐年加强的态势；影响耦合协调度的主要因素有从业人口数、固定资产投资额、人均生产总值、人口总数、[JP]文盲人口占比、工业污染排放、城镇化。