Facile synthesis of Ti3C2 MXene-modified Bi2.15WO6 nanosheets with enhanced reactivity for photocatalytic reduction of Cr(VI)

Through a facile hydrothermal method, we have successfully prepared Ti₃C₂/Bi_2.15WO₆ (TC/BWO) composite, and systematically investigated their reactivity for the photocatalytic reduction of Cr(VI) under visible light. X-ray diffraction and Raman analysis confirm the formation of heterostructure between Bi_2.15WO₆ and Ti₃C₂. The resultant 7TC/BWO composite exhibits enhanced photoactivity toward Cr(VI) reduction. After 120 min irradiation, the conversion of Cr(VI) reaches 92.5% with the quasi-first-order kinetic constant of k = 0.0145 min^?1, which is higher than that of pure BWO (30% and k = 0.0005 min^?1). The electrochemical and photoluminescent characterization confirm that the introduction of Ti₃C₂ is conducive to the separation of carriers, thus significantly improves the photocatalytic performance of TC/BWO. Furthermore, the radical capture experiments verify that the electrons are important for enhancing reduction of Cr(VI) to Cr(III). As a result, this research provides a comprehensive understanding of the reduction of Cr(VI) by TC/BWO composite under visible light.     

控制爆破法处理卡钻事故

介绍了在包头市某工程实施管道穿越黄河施工中,采用爆破法处理卡钻的经验。针对深水环境条件及钻杆内径小不宜采用集团装药的条件,确定采用"小直径爆破筒,钻杆内部装药"的爆破方案,阐述了爆破设计及施工注意事项。可供类似工程参考。     

An analytical model for gas leakage through contact interface in proton exchange membrane fuel cells

Sealing performance between two contacting surfaces is of significant importance to stable operation of proton exchange membrane (PEM) fuel cells. In this work, an analytical micro-scale approach is first established to predict the gas leakage in fuel cells. Gas pressure and uneven pressure distribution at the interface are also included in the model. At first, the micro tortuous leakage path at the interface is constructed by introducing contact modelling and fractal porous structure theory. In order to obtain the leakage at the entire surface, contact pressure distribution is predicted based on bonded elastic layer model. The gas leakage through the discontinuous interface can be obtained with consideration of convection and diffusion. Then, experiments are conducted to validate the numerical model, and good agreement is obtained between them. Finally, influences of surface topology, gasket compression and gasket width on leakage are studied based on the model. The results show that gas leakage would be greatly amplified when the asperity standard deviation of surface roughness exceeds 1.0 μm. Gaskets with larger width and smaller thickness are beneficial to sealing performance. The model is helpful to understand the gas leakage behavior at the interface and guide the gasket design of fuel cells.     

Real time power management strategy for fuel cell hybrid electric bus based on Lyapunov stability theorem

The fuel cell/battery durability and hybrid system stability are major considerations for the power management of fuel cell hybrid electric bus (FCHEB) operating on complicated driving conditions. In this paper, a real time nonlinear adaptive control (NAC) with stability analyze is formulated for power management of FCHEB. Firstly, the mathematical model of hybrid power system is analyzed, which is established for control-oriented design. Furthermore, the NAC-based strategy with quadratic Lyapunov function is set up to guarantee the stability of closed-loop power system, and the power split between fuel cell and battery is controlled with the durability consideration. Finally, two real-time power management strategies, state machine control (SMC) and fuzzy logic control (FLC), are implemented to evaluate the performance of NAC-based strategy, and the simulation results suggest that the guaranteed stability of NAC-based strategy can efficiently prolong fuel cell/battery lifespan and provide better fuel consumption economy for FCHEB.     

Dynamic simulation of hydrogen-based off-grid zero energy buildings with hydrogen storage considering Fanger model thermal comfort

In this study, some locations with different climates, off-grid zero energy buildings with hydrogen energy storage systems are designed, and transient analysis is conducted. These considered buildings supply their electricity consumption without using the electrical grid and PV panels or wind turbines. Also, they supply thermal comfort to occupants by using a vapor compression chiller and humidifier. Domestic hot water of occupants is supplied using solar collectors. For analyzing building's performance and objectives achievement, TRNSYS software is used. Also, for evaluating occupant thermal comfort, the Fanger model is used. The considered building is a one-story building with a 150 m² area. Four occupants are considered. Both of them are seated at rest, and another is seated with light working such as typing. Using the Fanger model equation and MATLAB software, the thermal comfort of occupants is determined. For domestic hot water consumption, verified profiles that vary during 24 h of the day are considered. Achieved results show that for humid and cold cities, PV panels with an area of 73 and 76 m² can be supplied the required electricity of considered building with four occupants and battery state of charge is higher than 50% and 10%, respectively. Moreover, with a suitable air conditioner system, the predicted percentage of dissatisfied (PPD) can be lower than 12% and 8% for humid and cold cities. Therefore, the building can be converted to a zero-energy building using its rooftop area.     

Enhanced oxygen evolution reaction kinetics through biochar-based nickel-iron phosphides nanocages in water electrolysis for hydrogen production

Highly-efficient and stable non-noble metal electrocatalysts for overcoming the sluggish kinetics of oxygen evolution reaction (OER) is urgent for water electrolysis. Biomass-derived biochar has been considered as promising carbon material because of its advantages such as low-cost, renewable, simple preparation, rich structure, and easy to obtain heteroatom by in-situ doping. Herein, Ni₂P–Fe₂P bimetallic phosphide spherical nanocages encapsulated in N/P-doped pine needles biochar is prepared via a simple two-step pyrolysis method. Benefiting from the maximum synergistic effects of bimetallic phosphide and biochar, high conductivity of biochar encapsulation, highly exposed active sites of Ni₂P–Fe₂P spherical nanocages, rapid mass transfer in porous channels with large specific surface area, and the promotion in adsorption of reaction intermediates by high-level heteroatom doping, the (Ni_0.75Fe_0.25)₂P@NP/C demonstrates excellent OER activity with an overpotential of 250 mV and a Tafel slope of 48 mV/dec at 10 mA/cm² in 1 M KOH. Also it exhibits a long-term durability in 10 h electrolysis and its activity even improves during the electrocatalytic process. The present work provides a favorable strategy for the inexpensive synthesis of biochar-based transition metal electrocatalysts toward OER, and improves the water electrolysis for hydrogen production.     

A numerical study on nonlinear DPL model for analyzing heat transfer in tissue during thermal therapy

In the present paper, therapeutic treatment of infected tumorous cells has been studied through mathematical modeling and simulation of heat transfer in tissues by using a nonlinear dual-phase lag bioheat transfer model with Dirichlet boundary condition. The components of volumetric heat source in this model such as blood perfusion and metabolism are assumed experimentally validated temperature-dependent function, which gives more accurate temperature distribution in tissues through this model. We have used the finite difference and RK (4, 5) techniques of numerical methods to solve the proposed problem and obtained the exact solution in a particular case. After comparison, we got a good agreement between them. We have used dimensionless quantities throughout this paper. The effect of relaxation and thermalization time with respect to dimensionless temperature distribution has been analyzed in the treatment process.     

Farmers' preferences for adopting on-farm concentration of raw milk: Results from a discrete choice experiment in Germany

Milk concentrates are used in the manufacturing of dairy products such as yogurt and cheese or are processed into milk powder. Processes for the nonthermal separation of water and valuable milk ingredients are becoming increasingly widespread at farm level. The technical barriers to using farm-manufactured milk concentrate in dairies are minimal, hence the suspicion that the practice of on-farm raw milk concentration is still fairly uncommon for economic reasons. This study, therefore, set out to investigate farmers' potential willingness to adopt a raw milk concentration plant. The empirical analysis was based on discrete choice experiments with 75 German dairy farmers to identify preferences and the possible adoption of on-farm raw milk concentration. The results showed that, in particular, farmers who deemed the current milk price to be insufficient viewed on-farm concentration using membrane technology as an option for diversifying their milk sales. We found no indication that adoption would be impeded by a lack of trustworthy information on milk processing technologies or capital.     

高面板坝全寿命周期变形控制方法及应用

高面板坝的变形对面板的安全运行有着特别重要的影响，国内外已建的高面板坝工程中，因坝体变形大导致防渗面板挤压破损，坝体渗漏量大的实例较多，不得不降低水库水位进行修复处理，造成较大的经济损失乃至给大坝的长期运行留下安全隐患。通过发生挤压破损的实例分析，发现变形控制缺乏系统性是发生面板挤压破损的主要因素，为预防面板破损，系统提出了“控制坝体总变形，转化有害变形，适应纵向变形”的坝体变形控制方法，并在使用软硬岩混合料筑坝的董箐面板堆石坝中得到的应用，取得了良好效果，该工程运行至今达十余年，未见面板有挤压破损迹象，该方法对建设200 m以上乃至300 m级超高面板坝具有重要借鉴意义。