Nanocellulose-based reusable liquid metal printed electronics fabricated by evaporation-induced transfer printing

Reusable electronics have received widespread attention and are urgently needed. Here, nanocellulosebased liquid metal(NC-LM) printed circuit has been fabricated by the evaporation-induced transfer printing technology. In this way, the liquid metal pattern is embedded into the nanocellulose membrane, which is beneficial for the stability of the circuit during use. Besides, the NC-LM circuit is ultrathin with just tens of microns. In particular, the finished product is environmentally friendly because it can be completely dissolved by water, and both the liquid metal ink and the nanocellulose membrane can be easily recollected and reused, thereby reducing waste and pollution to the environment. Several examples of flexible circuits have been designed to evaluate their performance. The mechanism of evaporation-induced transfer printing technology involves the deposition, aggregation, and coverage tightly of the nanosized cellulose fibrils as the water evaporated. This study provides an economical and environmentally friendly way for the fabrication of renewable flexible electronics.     

Chicken nuggets-like core/shell nanosheet arrays as high performance flexible all-solid-state supercapacitor cathode and buckwheat shell as anode

The energy density of a flexible all-solid-state supercapacitor (ASC) requires new electrode material with special structure and morphology as a prerequisite for its secured improvement. In this paper, a new morphological exploration of chicken nuggets-like core/shell NiCo₂O₄/MnO₂ (NCM) nanosheet arrays on Ni foam was employed. The application of this special morphology aims to greatly improve the electrochemical performance of the cathode electrode. Additionally, Buckwheat Biochar (BBC) is utilized as the anode while the PVA/KOH thin film is prepared as the separator. The chicken nuggets-like core/shell NCM nanosheet arrays were obtained by a two-step hydrothermal method. A series of characterization methods were carried out to further support the core/shell's well-designed structure and precise composition. The tests exhibited excellent specific capacitance of 593.3 F g^?1 at 5 mA cm^?2 and outstanding cycling stability with a retention of 90% after 10000 cycles. Furthermore, the assembled NCM//BBC ASC device indicated a high specific capacitance (239 F g^?1 at the current density of 5 mA cm^?2), this is in due part of the unique architecture of NCM nanosheet arrays and interconnected special porous structure of the BBC and the thin film PVA/KOH. Hence, the assembled ASC device exhibited high energy density (an energy density of 58 Wh·kg^?1 at 3263 W kg^?1) and remarkable cycling stability.     

Design and validation of robotic bionic eye with multiple flexible ropes parallel mechanism inspired by oculomotor law

Producing a stable and agile bionic eye for visual image acquisition in robotics is a challenging task. In this paper, we design a bionic eye with mirror-symmetric distribution and cross-connection of flexible ropes. This mechanism is based on oculomotor law and the physiological structure of the extraocular muscles (EOMs). Specifically, the basic structural parameters are determined by Listing’s law, and the unique connection of the flexible ropes can realize the functions of the recti and oblique muscles. Furthermore, to mimic the trochlea structure, a pulley mechanism is constructed to permit the free movement of the flexible ropes. Through simulation and physical experiments, it is demonstrated that the bionic eye mechanism can move with agility under the structural parameters. The experimental results indicate that the proposed bionic eye mechanism has a superior motion accuracy of 2.798 mm, which is 6.7% of the maximum motion distance, and the repeatable accuracy of the mechanism can up to 0.210 mm.     

Structural load alleviation using distributed delay shaper: Application to flexible aircraft

Lightweight flexible aircraft suffers from unwanted oscillatory vibrations during aircraft manoeuvres. A recently developed distributed-delay signal (DZV) shaper is therefore proposed to be applied as a feedforward controller to alleviate the manoeuvre loads, as an alternative to traditional structural filters used routinely in this context. Structural filters are essentially linear low-pass filters with bandwidth below the significant flexible modes, applied to control signals generated either by the pilot’s direct input or by the flight control system. It has been showed that if instead a properly tuned signal shaper is used, better performance can be achieved: first, the target modes are significantly attenuated while the responsiveness of the aircraft is less compromised and secondly, the oscillatory nature of the vibrations are reduced. The high fidelity simulation results on a full scaled dynamic model of a highly flexible blended wing–body (BWB) aircraft show that in comparison to traditional structural filters, signal shapers significantly reduce the wing root loading (forces and moments) which provides potential structural benefits.     

Highly transparent low resistance ATO/AgNWs/ATO flexible transparent conductive thin films

Indium-free flexible transparent conductive thin films (TCFs) composed of silver nanowire (AgNW) networks and Sb doped SnO₂ (ATO) layers were prepared on polyethylene terephthalate (PET) substrates. The ATO layers were deposited via radio frequency (RF) magnetron sputtering at room temperature. The AgNWs were achieved via a modified polyol reduction method and embedded between the ATO layers. The effects of AgNW networks and ATO layers on electrical and optical properties of the ATO/AgNWs/ATO flexible tri-layer thin films are investigated. The ATO layers can improve the optical transmittance and reduce the resistivity of tri-layers, and the corresponding mechanisms are proposed. Typically, an ATO/AgNWs/ATO flexible tri-layers show a high figure of merit value (30.06 × 10^-3 Ω^-1) with a low sheet resistance of 7.1 Ω/sq. and a high transmittance of 85.7%. Meanwhile, the tri-layers present excellent mechanical flexibility, and the ATO layers acted as the protecting layers improve the adhesive and environmental stability at high temperature and humidity for the ATO/AgNWs/ATO flexible tri-layers. These results indicate that ATO/AgNWs/ATO flexible tri-layer thin films can be useful for the fabrication of wearable electronic devices.     

计及RSC控制的DFIG短路电流直流分量解析表达

现有文献针对计及转子变流器(RSC)控制的双馈感应风电机组(DFIG)定子短路电流解析表达,将定子磁链当作一阶直流衰减分量或忽略功率外环控制。基于DFIG电压、磁链和RSC控制方程,得到定子电流关于定子电压和定子功率的传递函数,提出定子电流的精确解析表达式。基于RSC内、外环PI参数关系,推导直流分量衰减时间常数和角频率关于PI参数的表达式。分析了RSC内外环PI参数对定子电流直流衰减分量的影响。仿真结果验证了解析表达式的准确性,为PI参数选取和保护装置测量、整定提供依据。     

考虑变幂数的畸变动力学相似试验模型设计方法及试验研究

动力学相似理论广泛应用于大型结构的振动试验，其中畸变相似用于解决结构的设计参数不满足等比例缩放时的相似问题，针对畸变相似关系中幂数为定值导致预测精度低的问题，提出考虑变幂数的畸变动力学相似试验模型设计方法。首先，在敏感性分析与中心差分理论推导的幂数表达式的基础上，将中心差分的范围不断扩大得到一组随相似比变化的幂数。采用最小二乘法将这组幂数拟合为关于相似比的函数并建立相似关系。然后，在多盘转子系统的数值算例中将变幂数法与文献中的两种方法进行对比，结果表明，变幂数法的预测精度较文献中的方法有很大提高。最后，通过试验研究验证了数值算例中动力学模型及临界转速求解的正确有效性。相似关系的建立是以模型的临界转速为基础，因此也验证了数值算例中的相似预测结果。     

加热工艺参数对12%Cr钢晶粒长大行为的影响

研究了不同加热工艺参数下(加热温度1050~1300 ℃,保温时间0.25~24 h)12%Cr超超临界转子钢的奥氏体晶粒长大行为,并通过光学显微镜(OM)观察晶粒尺寸的变化规律,建立晶粒长大数学模型。结果表明:随着加热温度增加,晶粒尺寸逐渐增加,加热温度低于1150 ℃时,晶粒尺寸增加明显,而温度高于1150 ℃后,晶粒尺寸逐渐趋于稳定;随着保温时间的增加,晶粒尺寸逐渐增加,保温时间增加到3 h后,晶粒尺寸增加趋势放缓。采用非线性回归方法和Arrhenius晶粒长大模型,建立了该钢的晶粒长大数学模型。     

印尼BAYAH电厂一次风机故障原因分析与处理

本文针对印尼BAYAH电厂一次风机设备故障，详细的分析了故障产生的原因，介绍了三点法找转子动平衡和工装车削式在线修复电机滑环工法，阐述了两种工法的原理以及实施步骤。     

Intense-pulsed-light irradiation of Ag nanowire-based transparent electrodes for use in flexible organic light emitting diodes

Silver nanowire (AgNW) based transparent electrodes are inherently coarse and therefore typically are only ever weakly bonded to a substrate. A remarkable improvement in the characteristics of a AgNW network film has, however, been achieved through a simple and short process of irradiating it with intense pulsed light (IPL). This not only avoids any severe deterioration in the optical characteristics of the AgNW film, but also significantly improves its electrical conductivity, adhesion to a polymeric substrate, and ability to endure bending stress. Most important of all, however, is the finding that the surface roughness of AgNW networks can also be improved by radiation. In a series of measurements made of organic light emitting diodes fabricated using these treated electrodes, it was revealed that the leakage current can be notably reduced by IPL treatment.