A Lane-Level Road Marking Map Using a Monocular Camera

The essential requirement for precise localization of a self-driving car is a lane-level map which includes road markings (RMs). Obviously, we can build the lane-level map by running a mobile mapping system (MMS) which is equipped with a high-end 3D LiDAR and a number of high-cost sensors. This approach, however, is highly expensive and ineffective since a single high-end MMS must visit every place for mapping. In this paper, a lane-level RM mapping system using a monocular camera is developed. The developed system can be considered as an alternative to expensive high-end MMS. The developed RM map includes the information of road lanes (RLs) and symbolic road markings (SRMs). First, to build a lane-level RM map, the RMs are segmented at pixel level through the deep learning network. The network is named RMNet. The segmented RMs are then gathered to build a lane-level RM map. Second, the lane-level map is improved through loop-closure detection and graph optimization. To train the RMNet and build a lane-level RM map, a new dataset named SeRM set is developed. The set is a large dataset for lane-level RM mapping and it includes a total of 25157 pixel-wise annotated images and 21000 position labeled images. Finally, the proposed lane-level map building method is applied to SeRM set and its validity is demonstrated through experimentation.      

SRS: Spatial-tagged radio-mapping system combining LiDAR and mobile-phone data for indoor location-based services

One of the most challenging issues in radio received signal strength (RSS)-based localization systems is the generation and distribution of a radio map with a coordinate system linked with spatial information in a large indoor space. This study proposes a novel spatial-tagged radio-mapping system (SRS) that effectively combines the heterogeneous properties of LiDAR and mobile phones to simultaneously perform both spatial and radio mappings. The SRS consists of synchronization, localization, and map building processes, and enables real-time spatial and radio mapping. In the synchronization process, the distance range, motion data, and radio signals obtained through the LiDAR and mobile phone are collected in nodal units according to the sensing time. In the localization process, a feature variance filter is used to control the number of features generated from LiDAR and estimate the positions at which the nodes are generated in real time according to the motion data and radio signals. In map building, the estimated positions of the nodes are used to extract spatial and radio maps by using a unified location coordinate system. To ensure mobility, the SRS is manufactured in the form of a backpack supporting LiDAR and a mobile phone; the usefulness of the system is experimentally verified. The experiments are performed in a large indoor shopping mall with a complex structure. The experimental results demonstrated that a common coordinate system could be used to build spatial and radio maps with high accuracy and efficiency in real time. In addition, the field applicability of the SRS to location-based services is experimentally verified by applying the constructed radio map to well-known fingerprinting algorithms using the heterogeneous mobile phones.     

Modeling unaccounted-for gas among residential natural gas consumers using a comprehensive fuzzy cognitive map

Residential natural gas consumption depends on several factors. Available tools and methods to identify, categorize, and validate effective factors have some limitations, making consumption modeling more complex. Once a comprehensive model of effective consumption factors is developed for residential gas consumers, it can predict consumption. In addition, such a model could be used to verify the accuracy of measuring devices in order to reduce unaccounted for gas (UFG). The key factors affecting residential gas consumption were identified based on previous studies and their mutual effects were analyzed using a fuzzy cognitive mapping (FCM) method. The most significant factors and their effects on natural gas consumption in the residential sector were determined. In this study, for the first time, the expected consumption for each consumer was estimated using a consumption index. Generally, if the estimated consumption is significantly different from the amount recorded by the meter, it could suggest a potential source of UFG. The proposed method was applied to the data collected from the residential gas consumers of a small region in Iran (Dasht-e Arjan region, Fars province), and the results demonstrate the effectiveness of the proposed method.     

利用平面约束的月球车立体匹配方法

为了满足月球车视觉系统对检测障碍物检测的时效性和可靠性的需求，提出了一种基于平面约束和自适应惩罚参数的半全局立体匹配算法。首先，对极线校正后的两幅图像进行SIFT特征点提取与匹配，同时提取边缘特征；然后，利用匹配的SIFT特征点拟合空间平面，并根据平面估计左右图像所有像素点的视差搜索范围；最后，基于传统的半全局匹配算法，采用自适应惩罚参数的策略对左右图像进行立体匹配。实验结果表明：所提出的算法有效地降低了计算复杂度，其计算复杂度只有传统方法的19.9%，对于视差不连续区域以及遮挡区域都能够获得正确的匹配结果。较传统半全局匹配方法无论在速度还是匹配精度上都得到明显提高，为对立体匹配的实际应用奠定了基础。     

[Zr0.73(Cu0.59Ni0.41)0.27]87Al13合金过冷液相区热塑性成形研究

为探究[Zr_(0.73)(Cu_(0.59)Ni_(0.41))_(0.27)]_(87)Al_(13)非晶合金的热塑性成形性能以及绘制其对应的热加工图谱,用Gleeble3500型热模拟压缩实验机对该非晶合金进行不同参数下的热模拟压缩实验。结果表明,合金在压缩过程中变形行为由牛顿流变演变为非牛顿流变;同时,过高或过低的热加工温度均能导致合金晶化;进一步对数据分析得到该合金在不同热塑性成形参数下的功率耗散图与流变失稳图,并绘制出相应的热加工谱图,谱图分析结果表明,该合金在温度为420与430℃、应变速率为10~(-3) s~(-1)时具有较高功率耗散系数且没有失稳区域,因此,合金可选的热塑性加工参数为温度420～430℃,应变速率10~(-3) s~(-1)。     

Propagation and termination of an internal crack in continuously cast austenitic stainless steel analyzed by ∑ values and the Schmid factor

The formation mechanism of an internal crack was clarified from the viewpoint of the crystallography and thermal expansion. An inverse pole figure map obtained by EBSD pattern showed that the crack propagated along the grain boundaries having high ∑ values within the columnar zone. After the crack initiation, these positions were considered to undergo cracking followed by propagation toward the equiaxed side. Near the termination position, the grains ahead of crack propagation had a Schmid factor higher than 0.45 consuming elastic strain energy. Thermal expansion measurements showed that the grain with (0 0 1) orientation had the largest expansion while that with (0 1 1) the smallest. The grain boundaries neighboring the combination of (0 0 1) and (0 1 1) grains had the largest thermal stress. Therefore, thermal stress contributed to the initiation of cracking. It was thus proposed to enlarge the equiaxed zone to prevent cracking by discontinuing the crack propagation.     

The organization of biological sequences into constrained and unconstrained parts determines fundamental properties of genotype–phenotype maps

Biological information is stored in DNA, RNA and protein sequences, which can be understood as genotypes that are translated into phenotypes. The properties of genotype–phenotype (GP) maps have been studied in great detail for RNA secondary structure. These include a highly biased distribution of genotypes per phenotype, negative correlation of genotypic robustness and evolvability, positive correlation of phenotypic robustness and evolvability, shape-space covering, and a roughly logarithmic scaling of phenotypic robustness with phenotypic frequency. More recently similar properties have been discovered in other GP maps, suggesting that they may be fundamental to biological GP maps, in general, rather than specific to the RNA secondary structure map. Here we propose that the above properties arise from the fundamental organization of biological information into ‘constrained'' and ‘unconstrained'' sequences, in the broadest possible sense. As ‘constrained'' we describe sequences that affect the phenotype more immediately, and are therefore more sensitive to mutations, such as, e.g. protein-coding DNA or the stems in RNA secondary structure. ‘Unconstrained'' sequences, on the other hand, can mutate more freely without affecting the phenotype, such as, e.g. intronic or intergenic DNA or the loops in RNA secondary structure. To test our hypothesis we consider a highly simplified GP map that has genotypes with ‘coding'' and ‘non-coding'' parts. We term this the Fibonacci GP map, as it is equivalent to the Fibonacci code in information theory. Despite its simplicity the Fibonacci GP map exhibits all the above properties of much more complex and biologically realistic GP maps. These properties are therefore likely to be fundamental to many biological GP maps.     

Robust skin detection in real-world images

Human skin detection in images is desirable in many practical applications, e.g., human–computer interaction and adult-content filtering. However, existing methods are mainly suffer from confusing backgrounds in real-world images. In this paper, we try to address this issue by exploring and combining several human skin properties, i.e. color property, texture property and region property. First, images are divided into superpixels, and robust skin seeds and background seeds are acquired through color property and texture property of skin. Then we combining color, region and texture properties of skin by proposing a novel skin color and texture based graph cuts (SCTGC) to acquire the final skin detection results. Comprehensive and comparative experiments show that the proposed method achieves promising performance and outperforms many state-of-the-art methods over publicly available challenging datasets with a great part of hard images.     

谐振变换器的ZVS软开关同步整流技术研究

以感应电能传输(IPT)谐振变换器为研究对象,研究了谐振变换器的ZVS同步整流(SR)技术。分析了基于SR技术IPT谐振变换器的工作原理,利用系统的谐振工作特性,提出了一种新颖的ZVS软开关SR实现方法。建立了系统频闪映射稳态数学模型,给出了ZVS软开关SR的周期不动点函数、数值求解状态变量及ZVS软开关SR工作周期的算法流程。在设计控制电路的基础上,通过实验验证了提出的同步整流技术的可行性。