Nano TiC-Graphene-Cu composites fabrication by a modified ball-milling method followed by reactive sintering: Effects of reinforcements content on microstructure,consolidation, and mechanical properties

A two-step mechanical milling followed by a reactive sintering process was used to synthesize Nano TiC-Graphene-Cu composites from a mixture of Cu, Ti, and Graphene (GN) powders in four different compositions, and effects of reinforcements content on the microstructure and mechanical properties were studied. The results showed that a part of GN reacted with Ti atoms in the matrix, leading to the successful formation of hybrid nanocomposites. Uniform distribution of in-situ TiC with nanometer size and unreacted GN in the nanostructured Cu (Ti) solid solution were obtained. Addition of high percentage of the reinforcements led to an increase in the porosity and microhardness, coarsening of TiC nanoparticles, and decreasing the grain size of the matrix after sintering. The simultaneous presence of GN and TiC nanoparticles in the Cu matrix improved the hardness and wear resistance and reduced the friction coefficient by self-lubricating behavior. The nanocomposite with the nominal composition of Ti-40 vol % TiC showed the highest wear resistance and the lowest friction coefficient.     

Evaluation of oxy-acetylene flame angle effect on the erosion resistance of SiC/ZrB2–SiC/ZrB2 multilayer coatings fabricated by the shielding shrouded plasma spray technique

In the present study, the effect of oxy-acetylene flame angle on the erosion resistance of SiC/ZrB₂–SiC/ZrB₂ multilayer coatings with the gradient structure was investigated. To this aim, first, the SiC inner layer was applied by the reactive melt infiltration (RMI) technique; then ZrB₂ and ZrB₂–SiC layers with 10, 20 and 30%wt. SiC were applied on graphite by the plasma spraying technique. To prevent the oxidation of ZrB₂ and SiC particles, the plasma spraying process was performed by a solid protective shield. To evaluate the performance of the coatings in erosive environments, the samples were exposed to oxy-acetylene flame at the angles of 30°, 60° and 90° for 360 s; the destruction mechanism of SiC/ZrB₂–SiC/ZrB₂ multilayer coatings appeared to be controlled mechanically and chemically. The results of the erosion test showed that at the low flame angles of about 30°, due to the shear forces of oxy-acetylene flame, mechanical erosion overcame the chemical one. With increasing the flame angle, due to raising the surface temperature, chemical erosion overcame the mechanical one; so, most chemical destruction occurred at the flame angle of 90°. Also, the results of the erosion test showed that the total chemical and mechanical destruction at the angle of 60° was greater than that in other angles. Also, among the coatings tested, SiC/ZrB₂- 20% wt. SiC/ZrB₂ coatings had the best erosion resistance; so, the weight changes under the oxy-acetylene flame at the angles of 30° and 60°, respectively, were about ?0.038%. and ?0.355%; meanwhile, at the angle of 90°, it was about +4.3%.     

Physical properties of microwave and solid state synthesized La0.7Na0.3MnO3

We report the structural, magnetic, electrical and broadband microwave absorption in La_0.7Na_0.3MnO₃ sample synthesized by microwave (MW) irradiation (Na_0.3LMO_MW) and compare them to the sample synthesized by solid-state (SS) reaction method (Na_0.3LMO_SS). Single phase Na_0.3LMO_MW was synthesized at 800 °C in 30 min, whereas, Na_0.3LMO_SS sample was obtained by sintering at 1200 °C for 48 h. Although both these samples show ferromagnetic transition at T_C ～324.8 K, the MW-synthesized sample shows distinct physical properties: broad ferromagnetic transition, smaller saturation magnetization, a large difference between the magnetic ordering and metal-insulator transition temperatures, a large high-field magnetoresistance, a table top-like magnetocaloric effect, and a large low-field microwave absorption compared to the solid state synthesized sample. These differences are suggested to arise from magnetic heterogeneity induced by smaller grain size and surface spin disorder in the MW synthesized La_0.7Na_0.3MnO₃.     

Recent progress on low-cost ceramic membrane for water and wastewater treatment

Great progress in the development of low-cost ceramic membranes from alternative materials have been achieved recently towards various application especially water and wastewater treatment. However, their significance has not been fully recognized and understood especially in term of their microstructural analysis such as formation of grain growth and microcracks. This review paper summarizes fabrication method, alternative materials, microstructure, wettability, mechanical properties and application of low-cost ceramic membrane. The fabrication method including slip casting, tape casting, extrusion, pressing method and phase inversion technique are described. Alternative materials used in low-cost ceramic membrane fabrication are discussed and categorized into clays, agricultural waste, industrial waste and animal bone waste. The mechanisms of morphology formation, microstructure and wettability properties are analysed. Modification strategies for the surface of low-cost ceramic membrane are discussed, and classified into modification for separation application, modification for photocatalytic application and modification for membrane distillation and membrane contactor system. Modification improves the membrane structure by changing the pore size, porosity and wettability properties of low-cost ceramic membranes. Mechanical properties of low-cost ceramic membranes are also discussed in detail towards several mechanism, like grain growth phenomenon and formation of microcracks which also considered as membrane defects. Grain growth phenomenon can be divided into normal and abnormal grain growth. Meanwhile, formation of microcracks could be occurred in single-phase polycrystalline ceramics that have anisotropic grains or biphasic polycrystalline grains. The application of low-cost ceramic membrane in seawater desalination, oily wastewater treatment, heavy metal adsorption, textile separation and photocatalytic application are reviewed. Finally, some possible opportunities and challenges for further development of low-cost ceramic membrane are pointed out.     

Initial and residual trapping of hydrogen and nitrogen in Fontainebleau sandstone using nuclear magnetic resonance core flooding

Hydrogen is among a few promising energy carriers of the future mainly due to its zero-emission combustion nature. It also plays an important role in the transition from fossil fuel to renewable. Hydrogen technology is relatively immature and serious knowledge gaps do exist in its production, transport, storage, and utilization. Although the economical generation of hydrogen to the scale required for such transition is still the biggest technical and environmental challenge, unlocking the large-scale but safe storage is similarly important. It is difficult to store hydrogen in solid and liquid states and storing it in the gaseous phase requires a huge volume which is just available in subsurface porous media. Sandstone is the most abundant and favourable medium for such storage as carbonate rock might not be suitable due to potential geochemical reactions.It is well established in the literature that interaction of the host rock-fluid and injected gas plays a crucial role in fluid flow, residual trapping, withdrawal, and more generally storing capacity. Such data for the hydrogen system is extremely rare and are generally limited to contact angle measurements, while being not representative of the reality of rock-brine-hydrogen interaction(s). Therefore, we have conducted, for the first time, a series of core flooding experiments using Nuclear Magnetic Resonance (NMR) to monitor hydrogen (H₂) and Nitrogen (N₂) gas saturations during the drainage and imbibition stages under pressure and temperature that represent shallow reservoirs. To avoid any geochemical reaction during the test, we selected a clean sandstone core plug of 99.8% quartz (Fontainebleau with a gas porosity of 9.7% and a permeability of 190 mD).Results show significantly low initial and residual H₂ saturations in comparison with N₂, regardless of whether the injection flow rate or capillary number were the same or not. For instance, when the same injection flow rate was used, H₂ saturation during primary drainage was 4% and it was <2% after imbibition. On other hand, N₂ saturation during the primary drainage was 26% and it was 17% after imbibition. However, when the same capillary number of H₂ was utilised for the N₂ experiment, the N₂ saturation values were ～15% for initial gas saturation and 8% for residual gas saturation. Our results promisingly support the idea of hydrogen underground storage; however, we should emphasise that more sandstone rocks of different clay mineralogy should be investigated before reaching a conclusive outcome.     

Fabrication of alumina ceramics with functional gradient structures by digital light processing 3D printing technology

Alumina ceramics with different unit numbers and gradient modes were prepared by digital light processing (DLP) 3D printing technology. The side length of each functional gradient structure was 10 mm, the porosity ratio was controlled to 70%, and the number of units were (1 × 1 × 1 unit) and (2 × 2 × 2 unit) respectively. The different gradient modes were named FCC, GFCC-1, GFCC-2 and GFCC-3. SEM, XRD, and other characterization methods proved that these gradient structures of alumina ceramics had only α-Al2O3 phase and good surface morphology. The mechanical properties and energy absorption properties of alumina ceramics with different functional gradient structures were studied by compression test. The results show that the gradient structure with 1 × 1 × 1 unit has better mechanical properties and energy absorption properties when the number of units is different. When the number of units is the same, GFCC-2 and GFCC-3 gradient structures have better compressive performance and energy absorption potential than FCC structures. The GFCC-2 gradient structure with 1 × 1 × 1 unit has a maximum compressive strength of 19.62 MPa and a maximum energy absorption value of 2.72 × 105 J/m3. The good performance of such functional gradient structures can provide new ideas for the design of lightweight and compressive energy absorption structures in the future.     

建筑结构控制爆破拆除的力学分析与应用

应用运动学、动力学理论建立建(构)筑物控爆坍落过程的力学模型,进而研究在非定常约束条件下坍落结构的力学特征。首次提出了采用延时起爆技术时,非自由质点系及其广义坐标应是建立在每一段位上的瞬间虚位移。在此基础上,分析求解运动过程中时控单元的质点自由度,为精确选定爆破部位及时序提供了设计理论和计算依据。同时,结合振动理论,将控爆时差、结构载荷分布调制为振动系统,形成坍落结构梁板单元的强迫振动,充分实现在运动中进一步解体、破碎其自身结构,并形成具有明显缓冲效果的下落过程。应用实践结果证明力学分析是正确的,为工程结构爆破拆除计算机辅助设计及动态模拟技术的有效应用奠定了基础。     

Use of La2O3 with 8YSZ as thermal barrier coating and its effect on thermal cycle behavior,microstructure, mechanical properties and performance of diesel engine operated by hydrogen-algae biodiesel blend

In this present work, the effect of lanthanum oxides (La₂O₃) on the thermal cycle behavior of TBC coatings and mechanical properties such as adhesion strength and microhardness of 8% Yttria Stabilized Zirconia (8YSZ) TBCs were investigated. CoNiCrAlY and aluminium alloy (Al–13%Si) were used as bond coat and substrate materials. 8YSZ and different wt % of La₂O₃ (10, 20, and 30%) top coatings were applied using the atmospheric plasma spray (APS) method. The thermal cycling test for TBC coated samples were conducted at 800 °C in the electric furnace. The XRD pattern shows that the La₂O₃ doped 8YSZ material transformed to cubic pyrochloric structured La₂Zr₂O₇ during thermal cycling. Further, the Taguchi-based grey relation analysis (GRA) method was applied to optimize the TBC coating parameters to achieve better mechanical properties such as adhesion strength and microhardness. And the optimized La₂O₃/8YSZ TBC coating was coated on CRDI engine combustion chamber components. The engine was tested with microalgae biodiesel and hydrogen, and the results were promising for the TBC-coated engine. The engine performance increased while using La₂O₃/8YSZ coated components, and the emissions from engine exhaust gas such as CO, HC, and smoke reduced considerably. It was found that there was no separation crack and spallation of the coating layer in the microstructure. Ultimately, the microstructural analysis of the optimized TBC coated piston sample after 50 h of running in the diesel engine confirmed that the developed coating had a superior thermal insulation effect and longer life.     

Effects of multiple freeze–thaw cycles on meat quality,nutrients, water distribution and microstructure in bovine rumen smooth muscle

This study investigated the effect of 5 freeze–thaw cycles (freezing at −18°C for 12 h and then thawing at 4°C for approximately 12 h) on the meat quality, proximate composition, water distribution and microstructure of bovine rumen smooth muscle (BSM). As the number of freeze–thaw cycles increased, BSM pH, shear force, water content and protein content decreased by 3.06%, 35.50%, 14.49% and 21.11%, respectively, whereas BSM thawing loss, cooking loss, pressing loss, total aerobic count (TAC), ash content and fat content increased by 108.12%, 47.75%, 78.33%, 90.99%, 105% and 35.20%, respectively. The freeze–thaw cycles resulted in greater protein and lipid oxidation, as evidenced by a 36.46% reduction in the sulfhydryl content and a 209.06% and 338.46% increase in the carbonyl and malondialdehyde contents, respectively. Ice crystal formation disrupted the structural integrity of the muscle tissue. Low-field nuclear magnetic resonance results showed that the freeze–thaw cycles prolonged the relaxation times (T_2b, T₂₁ and T₂₂), indicating that immobile water shifted to free water, and consequently, free water mobility increased. After 3 freeze–thaw cycles, the decline in shear force slowed, the increase in thawing loss became accelerated, and the TAC approached the domain value (6 log colony-forming units/g). Therefore, the number of freeze–thaw cycles of smooth muscle during transport, storage and distribution should be controlled to 3 or fewer. The current results provide a theoretical basis and data support for the further utilisation and culinary processing of smooth muscle.