VO2/GaAs异质结的制备及其光电特性研究

采用直流磁控溅射和后退火氧化工艺在p型GaAs单晶衬底上成功制备了n-VO_2/pGaAs异质结,研究了不同退火温度和退火时间对VO_2/GaAs异质结性能的影响,并分析其结晶取向、化学组分、膜层质量以及光电特性。结果表明,在退火时间2 h和退火温度693 K下能得到相变性能最佳的VO_2薄膜,相变前后电阻变化约2个数量级。VO_2/GaAs异质结在308 K、318 K和328 K温度下具有较好的整流特性,对应温度下的阈值跳变电压分别为6.9 V、6.6 V和6.2 V,该结果为基于VO_2相变特性的异质结光电器件的设计与应用提供了可行性。     

Investigation on SCR-based ESD protection device for biomedical integrated circuits in a 0.18-μm CMOS process

In these decades, integrated circuits for biomedical electronics applications have been designed and implemented in CMOS technologies. In order to be safely used by human, all microelectronic products must meet the reliability specifications. Therefore, electrostatic discharge (ESD) must be taken into consideration. To protect the biomedical integrated circuits in CMOS technologies from ESD damage, a dual-directional silicon-controlled rectifier (DDSCR) device was presented in this work. Experimental results show that the DDSCR has the advantages of high ESD robustness, low leakage, large swing tolerance, and good latchup immunity. The DDSCR was suitable for ESD protection in biomedical integrated circuits.     

Iron Loss Calculation of AC Filter Inductor for Three‐Phase PWM Inverters

In recent years, remarkable advancement of new power semiconductor devices, such as SiC and GaN, enables the increase of switching frequency of power converters, and hence the volume of passive components, such as ac filters and transformers, can be reduced. However, temperature rise caused by the inductor loss is increasing, and hence iron loss evaluation of the inductor is one of the most important issues to realize high power density converters. Conventionally, an improved generalized Steinmetz equation (iGSE) has proposed in order to calculate the iron loss under a pulse voltage magnetizing condition. However, accurate iron loss calculation of the ac filter inductor used in a PWM inverter cannot be realized. The authors have proposed two methods of iron loss evaluation of ac filter inductors. The first one is a loss map method which can calculate the iron loss without using a real PWM inverter. Another one is an ILA (Inductor Loss Analyzer) which can measure the iron loss in every switching period in a real PWM inverter. In this paper, comparisons of the iron loss between the ILA and the loss map method on both the single‐phase and three‐phase inverters are studied. It is found that iron loss of the ac filter inductor in the three‐phase PWM inverter which is calculated by the loss map method cause a large error on a specific condition. In order to prevent the calculation error, the authors proposed a revised loss map method and proved the effectiveness of the method.     

Integrated circuit and system design for renewable energy inverters

This study proposes that a novel integrated circuit (IC) and system design for renewable energy inverters can harvest renewable energy to power direct current (DC) and alternating current (AC) loads. In addition, an intelligent synthesis and management tool is developed to design the proposed system and to judge the system’s operational maintenance decisions. Finally, a renewable energy inverter’s information is posted to an online system. Users can obtain the proposed system’s information at any time and place. The accurate and superior performance of the proposed IC and system is confirmed by computer simulations and experimental results.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Verification of Iron Loss Calculation Method Using a High‐Precision Iron Loss Analyzer

Because of the improved performance of power devices, the volume of the ac filter inductors used in high‐frequency PWM inverters has been reduced. However, the temperature rise in the filter inductor due to this miniaturization has become more pronounced. Therefore, we have proposed an iron loss calculation method for the ac filter inductor. However, the accuracy of the value calculated via the loss map method cannot be verified, because the iron loss arising during each switching period cannot be measured with conventional power measuring instruments. In order to resolve this problem, we developed an inductor loss analyzer (ILA), which allows precise measurement of the iron loss in the inductor during each switching period. The accuracy of the calculation of iron loss in the filter inductor by the loss map method was verified with the ILA. We found that the value calculated by the loss map method differed slightly from the value measured with the ILA. However, these differences can be reduced if we take into account the accurate flux density calculation and the effect of the duty ratio of PWM pulses on the loss. Finally, we verified that the loss map method can provide accurate iron loss calculations.     

离子膜法烧碱生产系统中电解整流控制系统的优化

针对20万t/a离子膜法烧碱装置中整流及其控制系统在长期运行过程中的不足,和引起系统不稳定的一些因素,提出了优化改进方法,以确保整流系统的安全、稳定运行。     

A New Design Methodology for Time-Based Capacitance-to-Digital Converters (T-CDCs)

This paper introduces a 9-bit time-based capacitance-to-digital converter (T-CDC). This T-CDC adopts a new design methodology for parasitic cancellation with a simple calibration technique. In T-CDCs, the input sensor capacitance is first converted into a delay pulse using a capacitance-to-time converter (CTC) circuit; then this delay signal is converted into a digital code through a time-to-digital converter (TDC) circuit. A prototype of the proposed T-CDC is implemented in UMC 0.13 μm CMOS technology. This T-CDC consumes 8.42 μW and achieves a maximum SNR of 45.14 dB with a conversion time of 1 μs that corresponds to a figure of merit (FoM) of 16.4 fJ/Conv.     

电流型阻抗源升压整流器

自Z源网络提出以来,阻抗源变流器得到了广泛的研究和应用,但大多是针对电压型及逆变器的。选择电流型准Z源整流器作为研究对象,在传统控制策略中加入了阻抗源电感电流的前馈控制和有源阻尼控制,得到了更高的输出范围和更好的输出波形,并通过仿真验证了控制策略的正确性。设计了1台1 kW量级的样机并进行实验验证。