Achieving fabrication of highly transparent Y2O3 ceramics via air pre-sintering by deionization treatment of suspension

An easy albeit quite effective deionization suspension treatment was adopted to alleviate the detrimental effects related to the hydrolysis of Y₂O₃ in an aqueous medium. Fabrication of highly transparent Y₂O₃ ceramics with a fine grain size via air pre-sintering and post–hot isostatic pressing (HIP) treatment without using any sintering additive was achieved using the treated suspensions. The hydrolysis issue of Y₂O₃ powder in an aqueous medium was effectively alleviated by using deionization treatment, and a well-dispersed suspension with a low concentration of dissolved Y³⁺ species was obtained. The dispersed suspensions were consolidated by the centrifugal casting method, and the green bodies derived from the suspension of 35.0 vol% solid loading showed an improved homogeneity with a relative density of 52.1%. Fully dense Y₂O₃ transparent ceramic with high transparency was obtained by pre-sintering consolidated green compacts at a low temperature of 1400°C for 16 h in air followed by a post-HIP treatment at 1550°C for 2 h under 200 MPa pressure. The sample had a fine average grain size of 690 nm. The in-line transmittance of the sample reached 83.3% and 81.8% at 1100 nm and 800 nm, respectively, very close to the theoretical values of Y₂O₃.     

Rapid preparation of Palygorskite/Al2O3 composite aerogels with superhydrophobicity,high-temperature thermal insulation and improved mechanical properties

Al₂O₃ aerogels are widely employed in heat insulation and flame retardancy because of their unique combination of low thermal conductivity and exceptional high-temperature stability. However, the mechanical properties of Al₂O₃ aerogel are poor, and the preparation time is considerably long. In this study, we present a simple and scalable approach to construct monolithic Pal/Al₂O₃ composite aerogels using solvothermal treatment instead of traditional solvent replacement, which remarkably shortened the preparation time. Subsequently, to obtain stable superhydrophobicity (θ > 152°), the Pal/Al₂O₃ aerogel was modified by gas-phase modification method. The obtained Pal/Al₂O₃ composite aerogels demonstrate the integrated properties of low density (0.078–0.106 g/cm³), low thermal conductivity (1000 °C, 0.143 W/(m·K)), good mechanical properties (Young's modulus, 1.6 MPa), and good heat resistance. The monolithic Pal/Al₂O₃ composite aerogels with improved mechanical performance and improved thermal stability can show great potential in the field of thermal insulation.     

Nanograin–glass dual-phasic,elasto-flexible,fatigue-tolerant,and heat-insulating ceramic sponges at large scales

Ceramics are considered intrinsically brittle at room temperature, which is mainly attributed to the limited availability of crystallographic slips and pre-existing geometrical flaws. Moreover, the lack of flexibility has severely hindered many high-end applications of ceramic materials. Here, we produce ceramic sponges that are simultaneously ultra-light, elasto-flexible, thermally insulating, and can fully recover from large deformation with a near-zero Poisson's ratio. These spongy materials also possess superb fatigue resistance without the accumulation of damage or structural collapse for 10,000 large-scale compressive or buckling cycles. We demonstrate the exceptional flexibility is enabled by the elastic distortion of nanograin–glassy dual phase and the fiber bulking in open-cell three-dimensional structure. Moreover, these spongy materials possess superior temperature-invariant superelasticity from deep cryogenic temperatures (−196 °C) to high temperature (1500 °C). Our study not only developed mechanically reliable lightweight ceramics for numerous extreme applications, but also provided new theoretical insights into the origin of flexibility in polycrystalline ceramics.     

Analysis of suitability of TPP ash-slag waste as materials for hydrogen fuel storage

The current trends in energy were described, the main of which is the use of alternative energy sources, especially hydrogen. The most common methods of hydrogen accumulation were proposed: accumulation of compressed gaseous hydrogen in high-pressure tanks; accumulation of liquid hydrogen in cryogenic tanks; storing hydrogen in a chemically bound state; accumulation of gaseous hydrogen in carriers with a high specific surface area. Based on the combination of advantages and disadvantages, the most promising methods of accumulation were selected: storage of liquid hydrogen and storage of hydrogen in carriers with a high specific surface area. The main requirement for materials for hydrogen storage by these methods was revealed – a high specific surface area. Prospects for the development of waste-free low-emission technologies due to the recycling of secondary raw materials and the development of low-temperature technologies for the synthesis of functional and structural materials were substantiated. The applicability of large-scale ash and slag waste from coal-fired thermal power plants as a raw material for obtaining materials by low-temperature technologies was shown. The traditional ways of using ash and slag waste as a raw material, active additive and filler in the production of cements were described. Modern technologies for the production of innovative materials with a unique set of properties were presented, namely carbon nanotubes, silica aerogel and geopolymer materials. The prospect of using geopolymer matrices as a precursor for the synthesis of a number of materials was described; the most promising type of materials was selected – geopolymer foams, which are mainly used as sorbents for purifying liquids and gases or accumulating target products, as well as heat-insulating materials. The possibility of obtaining products of any shape and size on the basis of geopolymer matrices without high-temperature processing was shown. The special efficiency of the development of the technology of porous granules and powders obtained from a geopolymer precursor using various methods was substantiated. The obtained granules can be used in the following hydrogen storage technologies: direct accumulation of hydrogen in porous granules; creation of insulating layers for liquid hydrogen storage units.     

面向智慧小镇建设的机房电气管线多目标优化布置方法

常规的管线布置优化方法难以在优化过程中得到全局搜索的最优解,导致安全性能无法得到保障,因此面向智慧小镇建设设计一个新的机房电气管线多目标优化布置方法。设置电气管线约束条件,将电压均值、单位时间内电流量、电气管线损耗恢复能力作为目标函数。优化管线布置全局搜索,使用交叉操作的方式不断得到更优解。建立多目标优化电气管线模型,得到电气管线多目标优化的数学模型。通过实验数据可知,该管线布置方法在算法测试中优于常规的3种算法,且在安全性能的检测中只与标准最优值相差6.22×10⁴,3个常规方法与标准最优值的差距为6.813×10⁴、7.6×10⁴、8.32×10⁴,因此可知该多目标优化的管线布置方法可以得到更优解。     

Experimental research on combined effect of obstacle and local spraying water fog on hydrogen/air premixed explosion

In order to reveal the mechanism of water fog explosion suppression and research the combined effect of water fog and obstacle on hydrogen/air deflagration, multiple sets of experiments were set up. The results show that the instability of thermal diffusion under lean combustion conditions is the main influencing factor of hydrogen/air flame surface instability, and the existence of water fog will aggravate the hydrogen/air flame surface instability. When obstacle is not considered, 8 μm, 15 μm, 30 μm water fog can significantly reduce the flame velocity and explosion overpressure of hydrogen/air, 45 μm fine water fog plays the opposite role. When considering the relative position of the water fog release position and the obstacle, the 8 μm, 15 μm, 30 μm water fog has almost no suppression effect when released near the obstacle, but a significant suppression effect occur, when using the 45 μm water fog. In the field of theoretical research, the research results not only provide an experimental basis for the fine water fog to reduce the consequences of hydrogen explosion accidents, and the optimal diameter range used by the water fog, but also provide experimental reference for the numerical simulation of hydrogen/air explosion suppression in semi-open space, and promote the development of hydrogen explosion suppression theory. In terms of engineering applications, this study can provide a theoretical basis for the layout of fire fighting equipment in the engine room of nuclear power plants or hydrogen-powered ships.     

Harvesting Air and Light Energy via “All-in-One” Polymer Cathodes for High-Capacity,Self-Chargeable,and Multimode-Switching Zinc Batteries

Aqueous rechargeable Zinc (Zn)–polymer batteries are promising alternatives to prevalent Li-ion cells in terms of cost, safety, and rate capability but they suffer from limited specific capacity in addition to poor environmental adaptability. Herein, air and light are successfully utilized from external environments in single near-neutral two-electrode Zn batteries to enable remarkably improved electrochemical performance, fast self-charging, and switchable multimode-operation from Zn–polymer to Zn–air cells. This system is enabled by a well-designed polyaniline-nanorod-array based “all-in-one” cathode combining reversible redox capability, oxygen reduction activity, and photothermal-responsiveness. The initiative design allows perfect integration of multiple energy harvesting from ambient “air” and light, energy conversion, and storage in one single cathode. Thus, it can act as an efficient light-assisted electrically-rechargeable Zn–polymer cell featuring the highest specific capacity of 430.0 mAh g⁻¹ among all existing polymer cathodes. Without external power sources, it can be self-charged to deliver a high discharging capacity of 363.1 mAh g⁻¹ by concurrently harvesting chemical energy from air and light energy for only 20 min. It can also switch to a light-responsive Zn–air battery mode to surmount the output capacity limit of Zn–polymer battery mode for continued electricity supply.     

Effect of functionally graded structure design on durability and thermal insulation capacity of plasma-sprayed thick thermal barrier coating

This paper aimed to design and optimize the structure of a thick thermal barrier coating by adding graded layers to achieve a balance between high thermal insulation capacity and durability. To this end, conventional TBC, conventional TTBC, and functionally graded TTBCs were deposited on the superalloy substrate by air plasma spraying. To determine the quality of the bond strength of the coatings, the bonding strength was measured. The durability of coatings was evaluated by isothermal oxidation and thermal shock tests. Then, at a temperature of 1000 °C, the thermal insulation capacity of the coatings was carried out. The microstructure of the coatings was characterized by a scanning electron microscope. The results showed that the thickness of the TGO layer formed on the bond coat in the conventional TBC and TTBC under the oxidation test at 1000 °C after 150 h was 2.79 and 2.11 μm, respectively, whereas, in the functionally graded TTBC samples, no continuous TGO layer was observed as a result of internal oxidation. The functionally graded TTBC presented higher durability than conventional TTBC due to improved bonding strength, thermal shock resistance, and the lack of a TGO layer at the bond/top coat interface. Also, the thermal insulation capacity of the functionally graded TTBC (with 1000 μm thickness of YSZ coating) was better than TTBC.     

A novel Ag–CuAlO2 sealant for reactive air brazing of 3YSZ and AISI 310S

Based on reactive air brazing (RAB), we designed a new type of sealant (Ag–xCuAlO₂) for joining 3 mol.% yttria-stabilized zirconia (YSZ) ceramics and AISI 310S stainless steel. The CuAlO₂ content affected the wettability of the sealant on the YSZ surface, and the joints had a high shear strength when Ag–2 wt.%CuAlO₂, which had a small contact angle on the YSZ substrate, was used as the sealant. In addition, the thickness of the oxide layer was reduced compared to that for the Ag–CuO sealant. The effects of the processing parameters on the microstructure and shear strength of the joints were investigated, and the as-brazed joints reached their highest shear strength (93.7 MPa) when brazed at 1040 °C for 30 min. After high-temperature oxidation at 800 °C for 200 h, the shear strength of the joints remained at 50 MPa, and no apparent change in the microstructure was observed, proving that the joints possessed excellent oxidation resistance.     

Characterization and exposure assessment of household fine particulate matter pollution in China

Household fine particulate matter (PM_2.5) pollution greatly impacts residents' health. To explore the current national situation of household PM_2.5 pollution in China, a study was conducted based on literature published from 1998 to 2018. After extracting data from the literature in conformity with the requirements, the nationwide household-weighted mean concentration of household PM_2.5 (HPL) was calculated. Subgroup analyses of spatial, geographic, and temporal differences were also done. The estimated overall HPL in China was 132.2 ± 117.7 μg/m³. HPL in the rural area (164.3 ± 104.5 μg/m³) was higher than that in the urban area (123.9 ± 122.3 μg/m³). For HPLs of indoor sampling sites, the kitchen was the highest, followed by the bedroom and living room. There were significant differences of geographic distributions. The HPLs in the South were higher than the North in four seasons. The inhaled dose of household PM_2.5 among school-age children differed from provinces with the highest dose up to 5.9 μg/(kg·d). Countermeasures should be carried out to reduce indoor pollution and safeguard health urgently.