Driving performance and road sign identification by multifocal contact lens wearers in a driving simulator

PurposeThe purpose of this study was to compare sign identification distances and driving performance metrics in presbyopic participants while wearing multifocal contact lenses (MFCL) and while wearing progressive addition lens (PAL) spectacles.Methods19 presbyopic participants completed PAL spectacle assessments and contact lens fitting and follow up visits before driving assessments began. These assessments occurred in a simulator equipped with a full-sized sedan on a motion platform and a 260 degree screen. Participants completed the driving task with PAL and with MFCL. Participants followed a lead car and identified signs at various distances from the road. For the two wearing conditions, comparisons of the distance along the road at which signs were identified were made using repeated measures ANOVA. Paired t-tests were used to compare driving performance for the two conditions.ResultsThere was no statistical difference in sign identification distance between PAL and MFLC for signs 32.0 m from the road side of the road (182 ± 46 m for MFCL; 205 ± 45 m for PAL; P = 0.07) or 51.4 m from the side of the road (204 ± 43 m for MFCL; 216 ± 36 m for PAL; P = 0.3). Only signs 70.2 m from the roadside showed a significant difference (207 ± 42 m with MFCL; 232 ± 39 m with PAL; P = 0.01), All distances were greater than those required to safely stop a vehicle. There were no significant differences in the driving performance metrics between the refractive corrections.ConclusionDriving performance metrics were similar for MFCL and PAL spectacles. Sign identification distances with both eyewear types were well within the distances required for safe vehicle stopping.     

微通道板表面羟基化工艺研究北大核心

研究了3种微通道板基底羟基化的方法,测量了羟基化处理后微通道板基底表面水接触角及通道端面的形貌变化,分析了各种方法中微通道板基底的亲水性和腐蚀情况。实验结果表明:氨水双氧水溶液对基体表面的亲水性能提升不大,NaOH溶液对基体有腐蚀作用,经食人鱼溶液处理的基体表面亲水性明显提高且无腐蚀作用。研究了微通道板在食人鱼溶液中的浸泡时间和浸泡温度对表面亲水性的影响。结果表明:随着浸泡温度的增加,微通道板表面水接触角先减小后增大,当温度为80℃时达到极小值,浸泡时间对微通道板表面的亲水性影响不大。最终确定了微通道板表面羟基化工艺:浸泡温度为80℃,静置时间为20~60 min。     

Analytical modeling of complex contact behavior between rock mass and lining structure

Based on the nondestructive test data of operating railway tunnels in China, this paper summarizes the basic characteristics of the complex contact behavior between the rock mass and lining structure. The contact modes are classified into dense contact, local non-contact, and loose contact. Subsequently, the corresponding mechanical model for each contact mode is developed according to its mechanical characteristics using the complex variable method. In the proposed mechanical model, a special algorithm is introduced to detect whether the local non-contact zone is re-contacted. Besides, a novel conformal mapping method is also proposed to accurately calculate the mechanical response of the concrete lining. Finally, the accuracy of the proposed method is verified by comparing it with the finite element method (FEM). Several parameter investigations are conducted to analyze the effects of different contact modes on the rock–lining interaction. The results show that: (i) the height of the local non-contact area does not have a significant effect on the contact stress distribution if no re-contact occurs; (ii) backfill grouting can reduce the local stress concentration caused by poor contact modes; and (iii) reducing the friction coefficient of the interface can lead to a more uniform distribution of internal forces in the concrete lining.     

接触器触头系统振动机理分析及算法优化

为了解决合闸过程中动、静触头接触引起的振动弹跳问题.本文建立了接触系统的二自由度运动微分方程,并利用遗传算法对交流接触器吸合过程进行优化,同时通过高速摄影实验对接触弹跳的全过程进行了观察和分析.结果表明:理论与实验结果高度一致,铁心在触头分离前发生碰撞,进一步加剧触头弹跳;铁芯弹跳再次碰撞时,触头的弹跳不受影响;在接触器运行过程中,动铁芯的运动会引起系统轻微振动;采用遗传算法优化的接触器触头弹跳时间和最大振幅均减小.研究结果为进一步控制和减小接触弹跳提供了理论依据.     

金属O形环密封结构的泄漏模型研究

基于分形理论的金属垫片泄漏模型,改进了密封面的接触模型,综合考虑了密封面微凸体的完全弹性、第一弹塑性、第二弹塑性和微凸体大小分布的域扩展因子;分析金属O形环密封接触宽度与设计压缩率的关系,推导出金属O形环密封结构的泄漏模型,并进行验证分析。结果表明:压缩率在一定范围内,接触宽度随压缩率的增加而逐渐增加;但当压缩率超过一定值后,O形环发生塌陷,导致接触宽度迅速减小;各压缩率下计算得到的泄漏率与试验结果在同一量级,说明建立的泄漏模型适用于金属O形环密封结构泄漏率的预测。     

径向弹簧蓄能密封结构最大接触应力的有限元分析

为研究径向弹簧蓄能密封结构的密封特性，针对典型径向弹簧蓄能密封结构，分析其密封机制以及O形弯曲金属螺旋弹簧的弹性特性；采用ANSYS有限元分析软件，建立典型弹簧蓄能密封结构的非线性有限元分析模型，对弹簧蓄能密封圈在不同压缩率、不同介质压力下的接触应力进行分析，研究在多种工况下最大接触应力的变化情况。结果表明：压缩率保持不变时，最大接触应力随着介质压力的增大而增大；介质压力保持不变时，随着压缩率的增大，最大接触应力先增大再减小。对压缩率、介质压力与最大接触应力的关系进行曲线拟合，可用于指导弹簧蓄能密封结构的精确设计。     

电感耦合等离子体质谱法测定食品接触材料及制品中钡、钴、铜、铁、锂、锰的迁移量

目的建立电感耦合等离子体质谱法同时测定食品接触材料及制品中钡、钴、铜、铁、锂、锰元素含量的方法。方法采用水、4%乙酸、10%乙醇、20%乙醇、50%乙醇和95%乙醇(V:V)作为食品模拟物进行迁移试验,试样溶液根据基质的差异选择不同的前处理方式,优化仪器参数和实验条件,最后由电感耦合等离子体质谱仪同时测定迁移试样溶液中6种金属元素的含量。结果各金属元素在一定的浓度范围内线性关系良好,相关系数大于0.999,方法检出限为0.3～9.0μg/kg,样品平均加标回收率为86.5%～109.1%,相对标准偏差为1.0%～8.3%。结论该方法简便易于操作,稳定可靠,检出限低,完全能够满足GB 9685-2016《食品安全国家标准食品接触材料及制品用添加剂使用标准》对金属元素特别限制规定的检测需求,为食品接触材料及制品中多种金属元素迁移量提供了一种高效可行的检测手段。     

基于有限元仿真的发泡硅橡胶老化规律研究

通过力学性能测试得到发泡硅橡胶应力应变曲线,结合Ogden(Foam) 3阶超弹本构模型,建立发泡硅橡胶静密封系统的有限元仿真模型,得到大压缩量下发泡硅橡胶的von Mises应力及接触压力分布情况。仿真结果表明:大压缩量下发泡硅橡胶对称中心线位置的von Mises应力、接触压力值较大,在橡胶边缘和靠近限位环处接触应力数值有突增。开展140℃热空气老化试验,测定老化后发泡硅橡胶应力应变曲线,结合有限元仿真模型分析发泡硅橡胶老化后von Mises应力、接触压力的变化规律。结果表明:经过热空气老化后,在一定载荷下发泡硅橡胶等效应力和接触压力均呈增大的趋势。     

CFD modeling of thermal contact resistance between solid contacting surfaces

Heat transfer has considerable applications in different industries such as designing of heat exchanger, nuclear reactor cooling, control system for spacecraft, and designing of microelectronics cooling. As the surfaces of two metals contact each other, this issue becomes so crucial. Thermal contact resistance (TCR) is one of the key physical parameters in heat transfer of mentioned surfaces. Measuring the experimental value of TCR in laboratory is highly expensive and difficult. As an alternative, numerical modeling methods could be engaged. In this study, inverse problem method solution is utilized as a proper method for estimation of TCR value. In this order, three different configurations (flat-flat, flat-cylinder, and cylinder-cylinder) were utilized in two steady and unsteady state conditions to predict the value of TCR. A comparison between the measured values and obtained values from the simulation show the errors for flat-flat, flat-cylinder, and cylinder-cylinder configuration after 10 min from starting the experiment are 4.6074%, 0.1662%, and 0.5622%, respectively. And in steady-state condition, the corresponding errors are 6.06e-3%, 1.506%, and 0.846%, respectively. In conclusion, the final results establish the fact that the inverse problem method solution can predict TCR values between contacting surfaces.     

厌氧接触+射流曝气+Fenton流化床技术处理制浆造纸废水运行实例

介绍厌氧接触+射流曝气+Fenton流化床技术处理制浆造纸生产废水的工程参数、运行效果和工程效益。六个月的运行数据显示,厌氧单元出水COD平均浓度为1321 mg·L^-1,平均去除率为61%;好氧单元出水COD浓度为185 mg·L^-1左右,平均去除率为78%;深度处理部分COD出水浓度为44 mg·L^-1,平均去除率为73%,可实现废水达标排放。