异种铁素体耐热钢接头界面组织及其影响

综述了铁素体与铁素体异种金属焊缝（dissimilar metal welds，DMWs）接头界面组织及其影响。结果表明，在焊后热处理或运行温度下的铁素体钢DMWs接头的不均匀界面组织中，通常会形成脱碳层和增碳层。在铁素体钢DMWs焊接接头界面组织影响因素中，焊缝金属的化学成分有重要影响；焊后热处理规范（温度和时间）、工作温度下运行时间的影响较为突出；焊接工艺参数的影响亦不可忽略。异种钢接头界面处近缝区裂纹的产生，以及接头的蠕变强度随Larson Miller 参数增大而下降等不利影响，均为异种钢界面碳迁移行为所导致。焊缝成分控制法是接头界面组织控制或改善的必要条件，而脱碳层部位转移法能有效防止裂纹发生，亦是接头安全运行的重要工艺措施之一。     

基于C#持久蠕变强度外推功能的实现

持久蠕变强度外推是预测材料在高温高压环境下工作寿命的有效方法。目前常用的外推方法有等温法和参数法。这两种方法都是通过在实验室中采用较短时间的试验，获取试验数据后，通过Excel或者MATLAB等数据处理软件进行数据的拟合处理和外推计算。这些数据归纳统计和数学建模的过程有时需要耗费试验人员的大量精力。介绍了持久蠕变强度外推的软件实现方法，该功能包含在持久蠕变试验设备配备的软件中，试验完成后，软件直接根据试验结果进行数据拟合和持久蠕变强度的外推计算，无需试验数据的统计和建模，大大提高了持久蠕变强度外推计算的效率。     

耦合效应下压力型锚索锚固机理的近似理论分析

为了更加精确地研究压力型锚索的锚固机理,基于锚索预应力与岩土体蠕变的耦合效应推导了锚索预应力方程。在此基础上根据Mindlin问题解,推导了耦合效应作用下锚索砂浆体的压应力和剪应力近似解,并考虑锚索预应力与岩土体蠕变之间的耦合效应进行了案例分析。研究结果表明:锚索预应力和砂浆体受到的应力峰值均按反幂函数随时间逐渐衰减并稳定;承压板的长宽比与压应力峰值之间存在正相关关系,与剪应力峰值之间存在负相关关系;岩土体的泊松比与应力峰值之间存在正相关关系。该成果丰富了压力型锚索锚固机理的理论研究,可为边坡锚固设计提供一定的理论依据。     

P91钢管道异常低硬度部位的组织和性能

对电厂运行过程中发现的P91钢主蒸汽管道的低硬度部位进行了微观组织观察、短时力学性能试验和高温持久强度试验,分析了其硬度偏低的原因。结果表明,低硬度区域P91钢组织为铁素体+析出物,位错密度较低,M₂₃C₆相在晶界处粗化聚集,同时析出新相Laves相,使得P91钢的短时力学性能和高温持久强度下降严重。     

Creep performance of CNT reinforced glass fiber/epoxy composites: Roles of temperature and stress

Carbon nanotubes (CNTs) have been emerged as a potential nanofiller to reinforce polymeric materials to improve their mechanical properties, like strength and modulus. However, time-dependent deformation of such materials under a constant load and elevated temperature is a matter of concern for long-term durability of these materials. The present article primarily demonstrates the effects of creep temperature and stress on the reinforcement efficiency of CNT in a glass fiber/epoxy (GE) composite. Two types of materials were investigated in this study—GE which was used as a control material, as well as CNT embedded GE composite. To elucidate the impact of CNT on the long-term durability of GE composite, creep tests have been performed at different temperatures (50, 80, and 110 °C) under bending loading. As applied stress has also significant contribution toward the elevated creep deformation of materials, creep tests have also been carried out under different stresses (5, 10, and 40 MPa). The strength of the CNT-GE composite exhibited 8.7 and 18.3% higher than that of control GE composite under tensile and bending load, respectively. Results suggest CNT reinforcement to be beneficial for low temperature applications, both in terms of creep strain and strain rate. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47674.     

Creep testing of carbon containing refractories under reducing conditions

Mechanical testing of carbon containing refractories at high temperatures requires measures to protect the sample from oxidation. Therefore, special setups for tensile and compressive creep testing were developed to prevent the oxidation of carbon in the sample. A MgO-C refractory was selected for a case study. These developments allow the quantification of the tensile and compressive creep behaviour of MgO-C refractories at temperatures up to 1500?°C. The creep parameters are determined by an inverse evaluation method for the obtained experimental data. They enable the consideration of creep in a thermomechanical finite element simulation of refractory linings in service.     

Effect of element Ru on microstructure and creep behaviour of single crystal nickel-based superalloy

By means of creep property measurement and microstructure observation, the influence of element Ru on the microstructure and creep behaviour of single crystal nickel-based superalloy is investigated. The results show that the plate-like μ phase is precipitated along {111} plane of the Ru-free alloy during thermal exposure at 1080°C and creep at 980°C. And the precipitation of μ phase in the alloy with 6(wt)%Mo and 6(wt)%W may be restrained by adding 2% Ru element. Compared to Ru-free alloy, the creep life of the 2% Ru single crystal alloy at 980°C200 MPa increases form 123 h to 333h. Compared to the 2% Ru alloy, the precipitated plate-like μ phase in the Ru-free alloy may promote the initiation and propagation of cracks along the γ matrix up to fracture, which is thought to be the main reason of the alloy having a lower creep resistances and shorter lifetime.