Progressive damage modelling of SMC composite materials

The present work deals with the modelling of damage behaviour for sheet moulding compound (SMC) composite materials using a finite element analysis package. Specifically, a comparison is made between the results obtained experimentally for a three-point bending test, and those obtained from numerical simulation using a material model already implemented. The simulation has been performed for the material models available within the PAM-CRASH software. The simulation results are compared and validated with respect to experimentation.     

原油基压裂液研究

研制了一种适用于低压、低渗、水敏性储集层的新型原油基压裂液体系。根据基液原油的组分合成相应的增稠剂，增稠剂在原油中与交联剂反应，形成网状结构，使原油成为黏度可以调控的冻胶，从根本上改变了油基压裂液以柴油、煤油为基液的现状，降低了油基压裂液的成本，同时还提高了压裂液的抗温、抗剪切和破胶性能，并将交联时间缩短到2h以内，可以满足现场压裂施工的要求，大大降低了施工强度和压裂改造的综合成本。在青海油田进行的现场先导试验取得成功。图9表1参5     

Segmented polymer networks containing amino‐dendrimers

Polymer networks in which poly(propylene imine) dendrimers (Astramol?) are connected to each other by linear polytetrahydrofuran (polyTHF) segments, were prepared by two methods. The first method was a one‐step procedure in which bifunctionally living polyTHF, obtained by initiation of the THF polymerization with trifluoromethane sulfonic anhydride (triflic anhydride), was reacted with an amino‐dendrimer. This reaction was very fast but did not allow formation of the end products. The second method was a two‐step procedure. In a first step, living polyTHF, prepared with acryloyloxybutyl triflate as initiator, was grafted on an amino‐dendrimer, to form a star‐like, acrylate‐terminated polyTHF multi‐macromonomer with the dendrimer as core. In a second step, networks were obtained by Michael addition between the acrylate end‐groups and unreacted amino‐groups of the dendrimer. This cross‐linking reaction occurred spontaneously upon heating of the solution of the multi‐macromonomer with gelation times varying from a few minutes to a few hours, depending on the temperature and the composition of the prepolymers. With this method it was possible to prepare networks in the form of coatings or films. © 2003 Society of Chemical Industry     

Model validation and model structure determination

This paper gives a tutorial overview of basic approaches for model validation and model structure determination.Work partially supported by the Swedish Research Council for Engineering Sciences under contract 98-654.     

心电图信号的频域分析

提出了一种简便有效的、由心电图（ECG）曲线提取QRS-T复合波的新方法，从而获得P波（当房颤未发生时）或f波（当房颤时）；利用功率谱、自相关、互相关等信号处理技术，对它进行了处理和分析，特别是，比较了未房颤时和发生房颤时的相关信息的显著差别。     

Sandia National Laboratories Validation Workshop: Structural dynamics application

This article specifies a virtual structural dynamic subsystem and some systems, as well as mathematical models that approximately simulate them. The purpose is to define a setting for model validations conceived by participants in the Sandia National Laboratories Validation Workshop. Some broad guidelines for the model validations are set, as well as a regulatory requirement to be satisfied by the target system. Participants are directed to present techniques for subsystem model validation, to analytically predict whether or not the regulatory requirement will be met, and to estimate the likelihood of accuracy of the prediction.     

Optimal and self‐tuning fusion Kalman filters for discrete‐time stochastic singular systems

Based on the optimal fusion estimation algorithm weighted by scalars in the linear minimum variance sense, a distributed optimal fusion Kalman filter weighted by scalars is presented for discrete‐time stochastic singular systems with multiple sensors and correlated noises. A cross‐covariance matrix of filtering errors between any two sensors is derived. When the noise statistical information is unknown, a distributed identification approach is presented based on correlation functions and the weighted average method. Further, a distributed self‐tuning fusion filter is given, which includes two stage fusions where the first‐stage fusion is used to identify the noise covariance and the second‐stage fusion is used to obtain the fusion state filter. A simulation verifies the effectiveness of the proposed algorithm. Copyright © 2008 John Wiley & Sons, Ltd.     

噪声测量作为筛选光电耦合器件的一种方法

本文针对目前用于光电耦合器件筛选方法的不足，提出了用测量耦合器件噪声功率谱的方法来筛选掉噪声值大的器件，给出一批光电耦合器件的测量统计结果及在不同工作点时的噪声功率谱，并给出相应的筛选标准，实验结果表明，这种方法是有效、可行的。     

复杂目标近场电磁散射的可视化计算方法

首次介绍了复杂目标近场散射计算的可视化方法。采用非均匀有理Ｂ样条曲面（ＮＵＲＢＳ）精确构造任意形状散射体，结合几何体近场透视变换和Ｚ－Ｂｕｆｆｅｒ技术实现了基于Ｗｉｎｄｏｗｓ平台的近场散射计算。提出广义雷达散射截面的概念并给出的若干算例。该方法充分利用了计算机３Ｄ图形设备的几何运算能力，运算速度快，严谨高，可扩展性好。     

梯形断面水力计算的一种新方法

本文从梯形水力最优断面的基本思路出发，通过理论分析找到了梯形断面水力计算的一种新方法——即通过特征参数进行梯形断面的水力计算。