气藏平均地层压力跟踪计算新方法

平均地层压力是产能评价和动态分析的基础，准确、快速获取平均地层压力对高效开发气藏意义重大。基于地层压力随时间变化的规律，分析了平均地层压力的变化规律。研究结果表明：平均地层压力等效点仅随时间发生改变，平均地层压力的下降速率等于或者近似等于井底流压的下降速率。从封闭弹性驱动气藏的物质平衡方程出发，考虑偏差系数和井底流压随平均地层压力的变化，推导建立了平均地层压力跟踪计算新方法，根据生产数据可迭代计算平均地层压力。方法验证结果显示，采气速度和采出程度共同影响模型的计算结果。应用实例表明，跟踪计算法与压力恢复试井和物质平衡法之间的相对误差均较小，满足工程计算精度要求，且跟踪计算法不需依托生产测试数据，节约了测试费用，避免了测试占产。     

用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

一种可控的自动扶梯电磁铁驱动电路板

扶梯制动系统是扶梯在出现紧急状况下确保乘客安全的重要设施。制动系统中的安全制动是在工作制动器无法在规定的时间内制停扶梯的一个措施,往往是在一些特别危险的场合下被触发,因此对于此制动器的控制显得尤为重要。本文提出了一种新型的自动扶梯制动器电磁铁驱动电路的设计,该设计用纯电子线路替代了传统的电气与电子组合形式,直接由自动扶梯单片机控制单元进行控制。     

Toughness enhancement and equivalent initial fracture toughness of cementitious composite reinforced with aligned steel fibres

Based on theoretical analysis and numerical simulation, the impact of steel fibres on the stress intensity factor (SIF) at the crack tip for cementitious composite was studied. The enhanced toughness of steel fibre reinforced cementitious composite (SFRC) in resisting cracks was explained by the decrement of SIF caused by steel fibre inclusions at the crack tip of the composite. The equivalent initial fracture toughness was used to characterize the crack initiation of SFRC. A simplified method for determining the of SFRC was proposed based on a linear regression method. Fracture tests were conducted on three‐point bending notched beams with different steel fibre volume fractions and specimen sizes to study the crack initiation behaviour of aligned steel fibre reinforced cementitious composite (ASFRC). of ASFRC was calculated, and the size effect of was analysed. The results showed that slightly increased with the steel fibre volume fraction and gradually became stable. For the tested specimens, whose heights varied between 40 and 100 mm, the specimen size had little impact on the .     

Topology optimization for crashworthiness of thin-walled structures under axial crash considering nonlinear plastic buckling and locations of plastic hinges

Although topology optimization is established for linear static problems, more effort is required for solving nonlinear plastic problems. A new topology optimization approach with equivalent static loads (ESLs) is suggested to find the optimum topologies and locations of plastic hinges of thin-walled crash boxes by considering crash-induced deformation, the main crash energy-absorbing mechanism. Together with finite element method crashworthiness analyses, considering all nonlinearities with rate-dependent plasticity, the method was developed using an appropriate time-incremental scheme of ESLs without removing any high values of loads. Analyses show that the crash boxes with optimum topologies have energy-absorbing capabilities equivalent to the original structure. The proposed method is evaluated for two crashes: a crash box at low speed and a double cell subjected to high-speed collision. The results indicate that this method captures nonlinear crushing behaviours and accurate locations of plastic hinges where, if proper reinforcements are made, energy absorption can be enhanced.     

Study on internal stress damage detection in long-distance oil and gas pipelines via weak magnetic method

Weak magnetic stress detection is an important issue in oil–gas pipeline internal detection area. In order to verify the characteristics of weak magnetic stress internal detection signals, we built herein a magneto-mechanics equivalent model having a balanced magnetic field. First, we calculated the relationship between the stress and the weak magnetic signals; consequently, the analysis propagation laws of the weak magnetic signals with non-magnetic saturation were pointed out. Finally, the theoretical model was validated by a systematic experimental research. The analytical results show that a one-to-one linear link between the weak magnetic signals and the stress concentration is clear. Instead, the change of the weak magnetic signals with the liftoff is nonlinear, therefore we are proposing the Boltzmann liftoff correction factor whose degree of adaptability of the equivalent model can reach the value of 94%. It is possible to note that when the liftoff is in the approximate linear stage, the relevance ratio and the recognition rate of the magneto-mechanics curve show a high-quality. This conclusion is important in the engineering field for the set of the liftoff.     

Study of planar structure applying reciprocity technique combined with MGEC and analysis of discontinuity

The 3D structure electromagnetic computation presents several difficulties related to the volume mesh. In fact, the entire volume space must be taken into account even the smallest details. In this article, we propose a formulation based on the reciprocity theorem combined with the generalized equivalent circuit method to model a planar 3D structure with both coaxial and planar excitation. The major advantage of this formulation is the fact to reduce the computational volume into 2D ones in the discontinuity plane. In addition, we focused on the calculation of the discontinuity between the excitation source and the planar structure to determine the exact behavior of the electric coaxial excitation model. The obtained current density, electric field distributions, and the input impedance are presented and discussed in the following sections. An approximately good agreement of input impedance with those obtained by the simulator and measurement is shown.     

QKD系统中基于EA电路的诱骗态实现

使用诱骗态量子秘钥方案可以解决因光子数分离攻击而导致的安全漏洞,保证了长距离量子通信的安全。本文介绍了量子通信的相关原理,通过对电吸收调制电路和激光器驱动电路的设计,精确控制产生了1550 nm波段的窄脉冲,经过内部调制成功制备诱骗态光脉冲,其强度约为信号态光脉冲的三分之一,因激光器的同一性而具有一致的光学特征从而避免了时频窃听,并具有强度可调的优点。     

基于一种改进逐点比较插补法的激光打标机控制加工算法

在激光打标系统中,逐点比较插补法是一种普遍使用的算法。这种算法在控制激光运动轨迹和对图像轨迹的拟合过程中,起到极其重要的作用。由于逐点比较插补法具有运算直观,脉冲输出均匀,调节方便等特点,所以是一种较为适合打标机系统应用的插补算法。但是传统的逐点比较插补算法存在精度低和速度慢等问题。为了改善该算法的性能,对传统逐点比较插补算法进行了改进,并进行了计算和模拟仿真。结果表明改进比较插补算法在精度和速度上都有明显提高。