Utilization of pyrolytic oil and hydrogen enriched syngas from single feedstock (delonix regia) through pyrolysis process and its influence on performance and emission characteristics in CI engine

The main objective of the present investigation is to conduct the performance, combustion and emission analysis of CI engine operated using hydrogen enriched syngas (pyrolytic gas) and biodiesel (pyrolytic oil) as dual fuel mode condition. Both the pyrolytic oil and syngas is obtained from single feedstock delonix regia fruit pod through pyrolysis process and then pyrolytic oil is converted into biodiesel through esterification. Initially biomass is subjected to thermal degradation at various pyrolysis temperature ranges like 350–600 °C. During the pyrolysis process syngas, pyrolytic oil and char are produced. The syngas is directly used in the CI engine and pyrolytic oil is converted into biodiesel and then used in the CI engine. The pyrolytic oil and syngas is subjected to FTIR and GC/TCD analysis respectively. The syngas analysis confirms the presence of various gases like H₂, CH₄, CO₂, CO and C₂H₄ in different proportions. The various proportions of the syngas is mainly depending upon the reactor temperature and moisture content in the biomass. The syngas composition varies with increase in the temperature and at 400 °C, higher amount of hydrogen is present and its composition are H₂ 28.2%, CO is 21.9%, CH₄ is 39.1% and other gases in smaller amounts. The biodiesel of B20 and syngas of 8lpm produced from the same feedstock are considered as test sample fuels in the CI engine under dual fuel mode operation to study the performance and emission characteristics. The study reveals that BTE has slight increase than diesel of 1.5% at maximum load. On the another hand emission like CO, HC and smoke are reduced by 15%,25% and 32% respectively at full load condition, whereas NO_x emission is increased at all loads in the range of 10–15%. Therefore B20+syngas of 8lpm can be used as an alternative fuel in CI engine without any modification and major products from pyrolysis process with waste biomass is fully used as fuel in the CI engine.     

Feeding behavior parameters and temporal patterns in mid-lactation Holstein cows across a range of residual feed intake values

Residual feed intake (RFI) is a measurement of the difference between actual and predicted feed intake when adjusted for energy sinks; more efficient cows eat less than predicted (low RFI) and inefficient cows eat more than predicted (high RFI). Data evaluating the relationship between RFI and feeding behaviors (FB) are limited in dairy cattle; therefore, the objective of this study was to determine daily and temporal FB in mid-lactation Holstein cows across a range of RFI values. Mid-lactation Holstein cows (n = 592 multiparous; 304 primiparous) were enrolled in 17 cohorts at 97 ± 26 d in milk (± standard deviation), and all cows within a cohort were fed a common diet using automated feeding bins. Cow RFI was calculated as the difference between predicted and observed dry matter intake (DMI) after accounting for parity, days in milk, milk energy, metabolic body weight and change, and experiment. The associations between RFI and FB at the level of meals and daily totals were evaluated using mixed models with the fixed effect of RFI and the random effects of cow and cohort. Daily temporal FB analyses were conducted using 2-h blocks and analyzed using mixed models with the fixed effects of RFI, time, RFI × time, and cohort, and the random effect of cow (cohort). There was a positive linear association between RFI and DMI in multiparous cows and a positive quadratic relationship in primiparous cows, where the rate of increase in DMI was less at higher RFI. Eating rate, DMI per meal, and size of the largest daily meal were positively associated with RFI. Daily temporal analysis of FB revealed an interaction between RFI and time for eating rate in multiparous and primiparous cows. The eating rate increased with greater RFI at 11 of 12 time points throughout the day, and eating rate differed across RFI between multiple time points. There tended to be an interaction between RFI and time for eating time and bin visits in multiparous cows but not primiparous cows. Overall, there was a time effect for all FB variables, where DMI, eating time and rate, and bin visits were greatest after the initial daily feeding at 1200 h, increased slightly after each milking, and reached a nadir at 0600 h (6 h before feeding). Considering the relationship between RFI and eating rate, additional efforts to determine cost-effective methods of quantifying eating rate in group-housed dairy cows is warranted. Further investigation is also warranted to determine if management strategies to alter FB, especially eating rate, can be effective in increasing feed efficiency in lactating dairy cattle.     

Droplet Entrainment Analysis in a Flash Evaporator with an Image-Based Measurement Technique

Local droplet sizes and volumes of entrained liquid are captured with an image-based measurement technique for comparison with a conventional, integral method for entrainment analysis. Experiments in a forced circulation flash evaporation were performed for different operating conditions and with two different chemical systems. Droplet size and frequency rise with an increase in thermal energy input. The local readings confirm the trends found by the integral measurement method. The modification of the image-based probe enables the detection of small (≈ 10 µm) and at the same time fast droplets under challenging operating conditions, such as vacuum and superheated feed similar to industrial process conditions.     

Determination of olaquindox,carbadox and cyadox in animal feeds by ultra-performance liquid chromatography tandem mass spectrometry

Olaquindox, carbadox, and cyadox are chemically synthesised antibacterial and growth-promoting agents for animals. At high doses they may exert mutagenicity and hepatic and adrenal toxicities in animals. Regrettably, these substances are frequently abused or misused when added into animal feeds. Thus, developing a sensitive and reliable method for simultaneous determination of olaquindox, carbadox, and cyadox in different kinds of animal feeds is crucially important for food safety monitoring. In this paper we optimised instrumental conditions, extraction solvents, solid phase extraction cartridges, and pH of the loading solvents on the Oasis HLB cartridge. Under the optimal conditions, mean recoveries ranged from 74.1 to 111%, and intra-day and inter-day variations were lower than 14.6% and 10.8%, respectively. The limits of quantification for olaquindox, carbadox, and cyadox were 0.05 mg kg^?1, 0.10 mg kg^?1, and 0.025 mg kg^?1, respectively. The proposed method uses ultra-performance liquid chromatography tandem mass spectrometry and is sensitive and reliable for the simultaneous determination of olaquindox, carbadox, and cyadox in three kinds of animal feeds (specifically, mixed feed, concentrated feed, and additive premixed feed). This method has good precision, high sensitivity, and good reproducibility, and thus it can be used for convenient and accurate determination of olaquindox, carbadox, and cyadox in different kinds of animal feeds.     

Quality and safety of maize (Zea mays L.) from Rondônia state storage units,Northern Brazil

The quality and safety of maize (Zea mays L.) from different grain storage units (GSUs), located in the main producing region of Rondônia State, Northern Brazil, were evaluated. Maize grains (n = 76) stored in four GSUs were collected from July to November 2014 and evaluated for grain damages, humidity, fungi and fumonisins (FBs) content. The climate conditions data were also obtained from plant growing to storage periods. Regarding the moisture content and water activity (a_w), these varied from 10.0% to 16.1% and 0.5 to 0.8, respectively. As expected, fungi spores were present in 94.8% of the samples, prevailing Fusarium genera, with a fungi colony maximum of 2.2 × 10⁴ CFU g^?1. Regarding FBs, 60.5% of the samples were contaminated, below Brazilian and United States maximum limits, but 9.2% had levels higher than the European legislation.     

The control of paracetamol particle size and surface morphology through crystallisation in a spray dryer

The parameters governing the crystallisation of paracetamol using various conventional techniques has been extensively studied, however the factors influencing the drug crystallisation using spray drying is not as well understood. The aim of this work was to investigate the crystallisation of an active pharmaceutical ingredient through evaporative crystallisation using a spray dryer to study the physicochemical properties of the drug and to use semi-empirical equations to gain insight into the morphology and particle size of the dried powder. Paracetamol solutions were spray dried at various inlet temperatures ranging from 60 °C to 120 °C and also from a series of inlet feed solvent compositions ranging from 50/50% v/v ethanol/water to 100% ethanol and solid-state characterisation was done. The size and morphology of the dried materials were altered with a change in spray drying parameters, with an increase in inlet temperature leading to an increase in particle Sauter mean diameter (from 3.0 to 4.4 µm) and a decrease in the particle size with an increase in ethanol concentration in the feed (from 4.6 to 4.4 µm) as a result of changes in particle density and atomised droplet size. The morphology of the dried particles consisted of agglomerates of individual crystallites bound together into larger semi-spherical agglomerates with a higher tendency for particles having crystalline ridges to form at higher ethanol concentrations of the feed.     

A new linearly constrained minimum variance beamformer for reconstructing EEG sparse sources

Brain source imaging based on EEG aims to reconstruct the neural activities producing the scalp potentials. This includes solving the forward and inverse problems. The aim of the inverse problem is to estimate the activity of the brain sources based on the measured data and leadfield matrix computed in the forward step. Spatial filtering, also known as beamforming, is an inverse method that reconstructs the time course of the source at a particular location by weighting and linearly combining the sensor data. In this paper, we considered a temporal assumption related to the time course of the source, namely sparsity, in the Linearly Constrained Minimum Variance (LCMV) beamformer. This assumption sounds reasonable since not all brain sources are active all the time such as epileptic spikes and also some experimental protocols such as electrical stimulations of a peripheral nerve can be sparse in time. Developing the sparse beamformer is done by incorporating L1-norm regularization of the beamformer output in the relevant cost function while obtaining the filter weights. We called this new beamformer SParse LCMV (SP-LCMV). We compared the performance of the SP-LCMV with that of LCMV for both superficial and deep sources with different amplitudes using synthetic EEG signals. Also, we compared them in localization and reconstruction of sources underlying electric median nerve stimulation. Results show that the proposed sparse beamformer can enhance reconstruction of sparse sources especially in the case of sources with high amplitude spikes.     

Drilling machinability of engineering ceramics under low-frequency axial vibration processing by sintering/brazing composite diamond trepanning bit

Thin-wall diamond trepanning bits are extensively used for processing hard and brittle materials such as engineering ceramics. However, it is difficult to achieve high-efficiency processing of engineering ceramics at a constant feed speed, because of high dynamic compressive strength, high hardness, and low density of engineering ceramics. In this study, a novel composite diamond bit combining sintering and brazing has been designed, along with the low-frequency axial vibration technology, to realize the continuous hole processing of engineering ceramics. Drilling experiments have been conducted on Al₂O₃ and SiC engineering ceramics with a constant feed speed. The variation of axial force, micromorphology of hole wall surface drilled, as well as the method of removing nesting during the drilling process were analyzed. According to the results, the novel composite diamond bit fabricated by combining sintering and brazing, can achieve the continuous hole processing of engineering ceramics at a constant feed speed, including Al₂O₃ and SiC. Compared to the conventional drilling (CD), the low-frequency axial vibration drilling (LFVD) can significantly reduce the axial force, and produce fewer plastic scratches on the hole wall surface drilled. In particular, the automatic blanking ratio approaches to 100% by LFVD, and only about 73.58% by CD. It can be concluded that LFVD technology can be used to realize continuous hole processing of engineering ceramics. The research results achieved in this study show that the drilling machinability of engineering ceramics by LFVD and novel composite diamond bit is good. Accordingly, this study provides a useful reference for continuous processing or batch production of engineering ceramics at a constant feed speed.     

An experimental approach towards increasing mechanical durability of extruded fish feed in the drying process

Mechanical durability of extruded fish feed must be optimized to lower economic losses as well as emission of organic matter to aquatic environments. The glass transition hypothesis for viscoelastic biopolymers is demonstrated and confirmed experimentally to be valid for extruded fish feed pellets. It is proposed and demonstrated that it is important to avoid early glass transition onset, to optimize the obtained mechanical durability. From the proposed glass transition hypothesis, immediate process relevance to the pre-drying transport mechanism is demonstrated. Furthermore, measured mechanical durability is found to range from 1.5 to 5.0% loss, for different combinations of drying parameters.     

Kinetic,thermodynamic parameters and in vitro digestion of tannase from Aspergillus tamarii URM 7115

Tannase is an enzyme used in various industries and produced by a large number of microorganisms. The aim of this study was to evaluate tannase production to determine the biochemical, kinetic, and thermodynamic properties and to simulate tannase in vitro digestion. The tannase-producing fungal strain was isolated from “jamun” leaves and identified as Aspergillus tamarii. Temperature at 26°C for 67?h was the best combination for maximum tannase activity (6.35-fold; initial activity in Plackett–Burman design—15.53?U/mL and average final activity in Doehlert design—98.68?U/mL). The crude extract of tannase was optimally active at 40°C, pH 5.5 and 6.5. Moreover, tannase was stimulated by Na⁺, Ca²⁺, Mg²⁺, and Mn²⁺. The half-life at 40°C lasted 247.55?min. The free energy of Gibbs, enthalpy, and entropy, at 40°C, was 81.47, 16.85, and ?0.21?kJ/mol?·?K, respectively. After total digestion, 123.95% of the original activity was retained. Results suggested that tannase from A. tamarii URM 7115 is an enzyme of interest for industrial applications, such as gallic acid production, additive for feed industry, and for beverage manufacturing, due to its catalytic and thermodynamic properties.