高稳高效海上风电安装平台关键制造技术研究

海上风电作为可再生清洁能源之一,受到世界各国的高度重视与大力发展。我国将海上风电提升至解决能源危机、减缓气候变化、调整能源结构的国家战略高度,到2030年我国单位国内生产总值二氧化碳排放将比2005年下降65%以上,非化石能源占一次能源消费比重将达到25%左右。安装平台不足将是我国海上风电场无法如期建成投产的主要障碍。对自升自航式海上风电安装平台系列高端装备及其设计制造的三大技术难题——腿站立作业易“失稳”、大平台大跨距大倾覆力矩自升易“失控”、高空吊装巨型叶片逾百螺栓精准定位易“失准”,以及焊缝缺陷修复和局部裂纹损伤的激光锻造修复再制造进行了介绍,研制的具有不同规格的系列装备在中国、英国、丹麦、德国等国家的著名海上风电场建设应用情况良好。     

复杂环境下氧化铝储槽定向爆破拆除

在较为复杂的环境下,爆破拆除钢筋混凝土氧化铝储槽。该储槽自重大、呈圆形,内有4根立柱支撑下料漏斗。为使储槽顺利定向倒塌,通过爆破方案选择、参数确定,采取梯形切口和预处理以及安全防护和减振措施,使储槽爆破拆除获圆满成功。     

风机主轴锻件锻后热处理工艺优化

通过对42CrMo4风机主轴结构尺寸、性能要求、材质特点等方面进行分析,对原有锻后热处理工艺进行优化,制定出既能达到锻后热处理效果又经济节能的工艺参数。     

热轧圆钢热顶锻裂纹原因分析

热顶锻合格率是反映热轧圆钢实物质量的一个重要指标。在对国内外热轧圆钢热顶锻质量控制研究成果综述的基础上，对热轧圆钢的热顶锻质量进行了全面的调查、统计和试验研究，归纳了引起热轧圆钢热顶锻裂纹的常见原因，介绍了热顶锻裂纹分析步骤。通过对热顶锻裂纹的形貌和金相组织进行分析，阐述了引起热顶锻裂纹的冶炼因素和轧制因素，并进行了举例说明。     

控轧控冷中碳非调质钢的高周疲劳性能

 采用中碳非调质钢制造的轴类等零件常承受交变载荷，因而对钢材疲劳性能具有高的要求。为了评估控轧控冷工艺生产的非调质钢棒材的疲劳性能，利用旋转弯曲疲劳试验机研究了一种常用的钒微合金化中碳非调质钢38MnVS及对比钢38MnS的高周疲劳性能。结果表明，与38MnS钢相比，38MnVS钢中铁素体体积分数增加，组织明显细化；相分析表明约有54%的钒处于M（C，N）相中，且尺寸小于10 nm的M（C，N）粒子质量分数为32%，这些细小粒子的析出强化增量约为116 MPa。38MnVS钢的疲劳极限较38MnS钢提高了62 MPa，提高幅度约为18%；疲劳极限比从38MnS钢的0.43提高到38MnVS钢的0.48。M（C，N）相的析出强化及组织细化是38MnVS钢较38MnS钢具有优异疲劳性能的主要原因，但其疲劳性能仍低于锻态非调质钢。根据试验结果及文献数据，给出了预测铁素体＋珠光体型非调质钢疲劳极限的简便方法。     

Effect of temperature on fast forging process of Mg-Ni samples for fast formation of Mg2Ni for hydrogen storage

Fast-Forging was used as a Severe Plastic Deformation technique to process Mg/Ni fine powder mixtures at a ratio corresponding to the eutectic composition. The samples were processed at different temperature, increased successively from room temperature up to above 500 °C. The one shock forging operation led to a reduction rate comprised between 80 to more than 90% depending of the applied temperature. Interestingly, a threshold temperature was pointed out for which amounts of the binary Mg₂Ni alloy were directly synthesized in increasing proportions when increasing temperature. A maximum amount of Mg₂Ni was synthesized according the nominal proportions at the highest applied temperature. Besides, numerical simulations were developed to consider and integrate to the forging process, the heat arising from the mechanical energy at deformation. Interestingly the total temperature at shock – heat applied to and heat developed in – indicates that the threshold temperature correspond well with the eutectic temperature as reported in the phase diagram. Early hydrogenation cycles suggest that both mechanical defects in brittle Mg and presence of amounts of Mg₂Ni as catalyst should be combined to optimize the hydrogenation characteristics.     

Microstructure and mechanical properties of TiC nanoparticle-reinforced Mg−Zn−Ca matrix nanocomposites processed by combining multidirectional forging and extrusion

TiC nanoparticle-reinforced Mg−4Zn−0.5Ca matrix nanocomposites were processed by combining multidirectional forging (MDF) and extrusion (EX). The grain size of the nanocomposite after MDF+EX multi-step deformation was significantly decreased compared with that processed only by MDF. The average size of the recrystallized grains gradually increased after EX with increasing the number of MDF passes at 270 °C. However, the grain size significantly decreased by MDF processing at 310 °C. Both fine and coarse MgZn₂ phases appeared in the (MDF+EX)-processed nanocomposites, and their volume fractions gradually increased with increasing the number of MDF passes before EX. Ultrahigh tensile properties (yield strength of ~404 MPa, ultimate tensile strength of ~450.3 MPa and elongation of ~5.2 %) were obtained in the nanocomposite after three MDF passes at 310 °C followed by EX. This was attributed to the refinement of the recrystallized grains, together with the improved Orowan strengthening provided by the precipitated MgZn₂ particles that were generated by MDF+EX multi-step deformation.     

控锻控冷工艺对GCr15轴承钢力学性能的影响

探究不同控锻控冷热处理工艺对GCr15钢力学性能的影响,测试了它的回火稳定性、冲击性能、滚动接触疲劳寿命。结果表明,采用控锻控冷工艺可提高试样的抗回火稳定性,冲击性能提高50%以上,接触疲劳寿命提高40%以上。     

18CrNiMo7-6环类锻件中白点缺陷的超声检测研究

将超声检测结果和缺陷波形特点进行分类和总结,并通过酸浸检验和断口检验对缺陷性质做出定性判断,验证了超声检测波形特征和白点缺陷的关联性,为通过超声检测手段来监控产品中是否存在白点缺陷提供参考。     

球头螺杆断裂原因分析

SCM440钢冲床球头螺杆使用了约1年就发生断裂。采用断口检验、金相分析、化学成分分析和力学性能测试等方法分析了球头螺杆断裂的原因。结果表明:球铁螺杆的显微组织为网状铁素体,晶粒粗大,并存在夹杂物、孔洞及锻造裂纹等缺陷,螺杆热处理过程中裂纹从这些缺陷处产生,并在使用中在应力的作用下扩展,最终导致螺杆断裂。