Influence of temperature on acoustic emission source location accuracy in underground structure

An acoustic emission (AE) experiment was carried out to explore the AE location accuracy influenced by temperature. A hollow hemispherical specimen was used to simulate common underground structures. In the process of heating with the flame, the pulse signal of constant frequency was stimulated as an AE source. Then AE signals received by each sensor were collected and used for comparing localization accuracy at different temperatures. Results show that location errors of AE keep the same phenomenon in the early and middle heating stages. In the later stage of heating, location errors of AE increase sharply due to the appearance of cracks. This provides some beneficial suggestions on decreasing location errors of structural cracks caused by temperature and improves the ability of underground structure disaster prevention and control.     

Fabrication of paper based carbon/graphene/ZnO aerogel composite decorated by polyaniline nanostructure: Investigation of electrochemical properties

The cellulose derived carbon/graphene/ZnO aerogel composite was prepared as an electrode in order to investigate the electrochemical properties. Carbon aerogel was synthesized using paper as an available cellulose source, and the composite was obtained through a new and simple preparation method including the immersion of monolithic carbon aerogel in graphene oxide/Zn²⁺ suspension and subsequent chemical reduction and freeze drying. The morphology, functional groups and crystalline structure of the samples were studied with Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Diffraction Spectroscopy (XRD), respectively. Electrochemical performance of the prepared binder free electrodes was examined using Cyclic Voltammetry (CV), Galvanostatic Charge-Discharge (GCD) and Electrochemical Impedance Spectroscopy (EIS). The data revealed that flexible carbon/graphene/ZnO composite resulted in a low density (0.035 g cm⁻³) electrode with the capacitance of 900 mF cm⁻² at a high current density of 10 mA cm⁻², lower IR drop and high cyclic stability (capacitance retention of 96%) after 1000 cycles, at 10 mA cm⁻². These features were due to the presence of 3D porous conductive network, highly reduced graphene oxide, and the formation of ZnO nanoparticles on graphene sheets. Moreover, polyaniline (PANI) was introduced to carbon/graphene/ZnO composite electrode using electro-oxidation method at different reaction time and aniline concentration in order to achieve remarkably improved capacitance of 2500 mF cm⁻² (at 10 mA cm⁻²) and low charge transfer resistance. Also, after the supercapacitor device assembly, the capacitance was retained. Based on the results, the synthesized composite is a promising material for new generation of lightweight freestanding electrodes with the high electrochemical performance.     

爆破位置对深凹露天矿山炮烟扩散的影响研究

深凹露天矿山由于其特殊的结构,爆破产生的炮烟扩散稀释较为困难,严重危害生产作业人员的生命安全与健康。基于实际矿山构建了深凹露天矿山的二维物理及数学模型,采用非稳态数值分析方法研究了不同爆破位置下,深凹露天矿山采坑内爆破炮烟的扩散规律。研究结果表明：不同爆破位置下,露天采坑内均出现复环流,爆破点位置是影响露天采坑内风流结构特征的重要因素；露天采坑内的炮烟最高浓度均随着时间变化而逐渐下降,但下降的速率逐步减小,呈现三个阶段的下降趋势；爆破位置位于背风侧时露天采坑内的炮烟最高浓度和降至安全浓度所需时间远高于迎风侧三个爆破位置；随着背风侧爆破点距采坑底部距离的减小,炮烟最高浓度及降至安全浓度所需时间先降低后增加,炮烟最高浓度及降至安全浓度所需时间随着迎风侧爆破位置距采坑底部距离的减小而增加。研究结果对于指导深凹露天矿山企业合理组织爆破后的生产作业和保障作业人员安全具有重要意义。     

Simply constructed highly dispersed cobalt nanoparticles in diverse N-doped graphitic carbon with remarkable performances for water electrolysis

Metal/carbon composite materials are highly promising electrocatalysts for water electrolysis. In this work, three composites of metal cobalt nanoparticles highly dispersed in N-doped carbon materials were facilely constructed by pyrolysis of different phenylenediamine based Schiff base-Co complexes (PDBs). Interestingly, the composites derived from PDBs based on different phenylenediamine exhibited different morphologies. The superior case is that rodlike composite catalyst was derived from o-phenylenediamine based PDBs. The obtained catalyst exhibited remarkable performances for both cathodic hydrogen evolution reaction (HER) and anodic oxygen evolution reaction (OER), as well as overall water electrolysis. Only 172 and 289 mV of overpotentials and 1.57 V of cell voltage were exhibited at 10 mA cm^?2 for HER, OER and water splitting in 1.0 M KOH, respectively. The catalyst also displayed robust stability and high Faraday efficiency, and thus are potential high-performance catalyst for commercial water electrolysis.     

The effect of biomass feeding location on rice husk gasification for hydrogen production

The objective of this study is to investigate the impact of biomass feeding location on rice husk gasification for hydrogen production. By comparing the results between top-feed and bottom-feed of the feedstock of the fluidized bed biomass gasification at the reaction temperature between 600～1000 °C and ER = 0.2, 0.27, and 0.33 without steam, the optimum low heating value was increase by 2.35 kJ/g-rice husk by the top-feed to gasifier. Although the yield of hydrogen was decreased by 42% for the rice husk gasification by the top-feed operation, the yield of CO, CO2, and CH4 were highly increased, which enhancing the heating value of the effluent gas. The study results suggested the potential route of the biomass gasification at the different feeding location.     

Identification and U-control of a state-space system with time-delay

This article presents a state-space model with time-delay to map the relationship between known input-output data for discrete systems. For the given input-output data, a model identification algorithm combining parameter estimation and state estimation is proposed in line with the causality constraints. Consequently, this article proposes a least squares parameter estimation algorithm, and analyzes its convergence for the studied systems to prove that the parameter estimation errors converge to zero under the persistent excitation conditions. In control system design, the U-model based control is introduced to provide a unilateral platform to improve the design efficiency and generality. A simulation portfolio from modeling to control is provided with computational experiments to validate the derived results.     

煤基高能量密度燃料的合成及表征

高能量密度燃料是为新型高性能飞行器提供动力保障的关键,其合成及应用研究具有重要的前瞻性和重大战略意义。煤炭是我国的主体能源和重要原料,通过煤直接转化获取的煤基油,充分保留了煤中特有的环状分子化学结构,具有良好的热安定性和较高的能量密度,被认为是高超音速飞行器的优选燃料。以煤直接液化工艺生产的煤液化石脑油馏分为起始原料,通过富集轻质芳烃、化学合成、催化加氢稳定和产物分离提纯等方法制备煤基高能量密度燃料,并对其产物进行分子结构表征和性能评价。结果表明,煤直接液化生产的石脑油馏分是一种优异的催化重整原料,经催化重整富集轻质芳烃后,其轻质芳烃质量分数高达71.05%。Diels-Alder化学合成主产物是由多个封闭环平面组成且具有空间立体构型的二环或三环烃类物质,质量分数为46.18%,因分子内存在较大的张力能,结构紧凑,其拥有更大的密度和体积热值。煤基高能量密度燃料的密度和体积热值分别为0.8990 g/cm3与38.06 MJ/L,均大大超过现行的国内石油基喷气燃料(RP-3和RP-6)、煤基大比重喷气燃料、美国和俄罗斯军用标准。与单一纯物质合成高能量密度燃料(JP-10和T-10)比较,其密度与体积热值偏小。究其原因主要是轻质芳烃的富集度仅为71.05%,需进一步提高其轻质芳烃质量分数。另外,制备的煤基高能量密度燃料种类复杂,其主产物质量分数仅46.18%,下一步可重点调控合成产物的分子构型和纯化分离。     

YOLSO: You Only Look Small Object

Small object detection is challenging and far from satisfactory. Most general object detectors suffer from two critical issues with small objects: (1) Feature extractor based on classification network cannot express the characteristics of small objects reasonably due to insufficient appearance information of targets and a large amount of background interference around them. (2) The detector requires a much higher location accuracy for small objects than for general objects. This paper proposes an effective and efficient small object detector YOLSO to address the above problems. For feature representation, we analyze the drawbacks in previous backbones and present a Half-Space Shortcut(HSSC) module to build a background-aware backbone. Furthermore, a coarse-to-fine Feature Pyramid Enhancement(FPE) module is introduced for layer-wise aggregation at a granular level to enhance the semantic discriminability. For loss function, we propose an exponential L1 loss to promote the convergence of regression, and a focal IOU loss to focus on prime samples with high classification confidence and high IOU. Both of them significantly improves the location accuracy of small objects. The proposed YOLSO sets state-of-the-art results on two typical small object datasets, MOCOD and VeDAI, at a speed of over 200 FPS. In the meantime, it also outperforms the baseline YOLOv3 by a wide margin on the common COCO dataset.     

M- S-H formation in MgO-SiO2slurries via wet milling for magnesia based castables

It is believed that the formation of hydration phase, MgO-SiO₂-H₂O (M-S-H), contributes to good workability and reliable comprehensive properties for magnesia based castables. In order to stimulate the formation of M-S-H in magnesia based castables and understand the minimum introduction of microslica amount, wet milling process was used to promote the dissolution of MgO and SiO₂ in this work. The slurry containing different content of microsilica with wet milling technology and the castables with/without wet milling slurry were prepared. The effects of microsilica content on the formation of hydration phases were analyzed by XRD, FT-IR and TG/DSC and the properties of magnesia based castables were evaluated by explosion resistance, CMOR, HMOR and so on. The results showed that the formation of M-S-H was accelerated because of the dissolution of Mg²⁺ and HSiO₃^? in wet milling process. Higher amount of M-S-H led to a tight bonding in the early stage, and a denser structure after firing at high temperature due to the limited formation of brucite and in-situ formation of evenly distributed forsterite phase. In addition, much higher HMOR were obtained when less microsilica was added, attributing to the suppressed formation of low-melting-point liquid. Therefore, 2–3 wt% microsilica addition was recommended in this process.