The As-prepared surfaces of C-axis-oriented Nd1Ba2Cu3Oy thin films characterized using scanning probe microscopes

Recently, superconducting Nd₁Ba₂Cu₃O_y (Ndl23) thin films with high superconducting transition temperature (T _c) have been successfully fabricated at our institute employing the standard laser ablation method. In this paper, we report the results of surface characterization of the Nd123 thin films using an ultrahigh vacuum scanning tunneling microscope/spectroscopy (UHV-STM/STS) and an atomic force microscope (AFM) system operated in air. Clear spiral pattern is observed on the surfaces of Nd123 thin films by STM and AFM, suggesting that films are formed by two-dimensional island growth mode. Contour plots of the spirals show that the step heights of the spirals are not always the integer or half-integer number of thec-axis parameter of the structure. This implies that the surface natural termination layer of the films may not be unique. This result is supported byI-V STS measurements. The surface morphology of the Nd123 thin films is compared with that of thec-axis-oriented Y₁Ba₂Cu₃S_y thin films. Surface atomic images of the as-prepared Nd123 thin films are obtained employing both STM and AFM. STS measurements show that most of the surfaces are semiconductive. The results of STS measurements together with the fact that we are able to see the surface atomic images using scanning probe microscopes suggest that exposure to air does not cause serious degradation to the as-prepared surfaces of Nd123 thin films.     

An Investigation of Milk Powders Produced by a Laboratory-Scale Spray Dryer

A mini spray dryer has been used to investigate morphological changes that occur to milk particles during the spray drying process. We have found that the mini spray dryer is ideal for such investigations, because phenomena such as skin and vacuole formation in particles can be analyzed without the added complication of particle agglomeration, which only occurs in much larger spray dryers where particle number concentrations are higher. We have confirmed observations made by various researchers that the bulk density of spray-dried milk powder is greatly affected by the drying temperature, due to the strong influence of the latter on the porosity of the particles. In addition, we have attempted to explain observations made by various workers that fat accumulates preferentially at the surface of a particle during drying by postulating that fluid fat is transported towards the surface, via a network of cracks and pores, by the development of a vacuole overpressure which is also responsible for the inflation of the particle. Finally, we have shown that milk powders can be spray dried a second time, by reconstitution with water, with no change to the thermodynamic characteristics of the resultant powder. Thus, milk concentrates for spray drying research can be prepared from already-spray-dried milk powders rather than using the more arduous evaporation method to concentrate unprocessed milk.     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

Synthesis and characterization of poly(siloxane-urethane)s

A series of polyurethane block copolymers based on hydroxy-terminated polydimethylsiloxane and poly(propylene glycol) soft segments of molecular weights 1818 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-diphenylnethane diisocyanate and 1,4-butanediol as the chain extender. Samples with different molar ratios were prepared. We tried to synthesize polydimethylsiloxane-based polyurethanes (PDMS-PU) containing a hard block as major fraction and a soft block as minor fraction for preparing toughened rigid systems. After a study of the pure polydimethylsiloxane-based polyurethane and poly(propylene glycol)-based polyurethane (PPG-PU), (mixed polyol)-based block copolymers and blends of PDMS-PU and PPG-PU were synthesized, and characterized by means of differential scanning calorimetry, tensile testing and scanning electron microscopy. In (mixed polyol)-based copolymers and lower hard-segment content blends, macro-phase separation occurred, but blends with higher hard-segment contents showed significant reduction in amounts of phase separation.     

Significance of fluid regime in biological filtration

A dispersed flow model previously developed to study substrate utilization in unsaturated media was experimentally verified and its practical application was considered. For this purpose, measurements were made using tap water and a synthetic feed solution. The importance of the change in fluid regime as regards to the simultaneous transport and reaction within biological filters were demonstrated. The effect of drop formation and the breakage of liquid jets inside the filters on substrate utilization was also shown.     

Morphological and kinetics study of PEO/PVC blends

The kinetics of spherulite radial growth and the morphology of the compatible system PEO/PVC have been studied by optical microscopy. The usual spherulite radial growth behaviour has been found for compatible blends with PEO content higher than 70%. For lower composition, distortion of the usual spherulite morphology has been observed; the anomalies have been attributed to partial miscibility of the components.     

The effect of support morphology on the reaction of oxidative dehydrogenation of ethane to ethylene at short contact times

The oxidative dehydrogenation of ethane is carried out in short contact time reactors over Pt and LaMnO₃ based catalysts supported on a large number of different ceramic substrates (45, 60 and 80 ppi foam monoliths and 200, 400, 600, 900 and 1200 cpsi honeycomb monoliths). Experimental results, obtained under the same conditions at varying the C₂H₆/O₂ ratio, showed that the highest performance in terms of ethylene selectivity and yield is always attained on LaMnO₃ catalysts. Furthermore, the results are significantly influenced by the morphology and cell density of the support, with 45 and 60 ppi foams and 400 and 600 cpsi honeycombs giving the best performance. The experimental results are explained by means of geometrical and fluid dynamic considerations on the support, and by means of a 2D mathematical model, which clearly indicates an optimal intermediate cell density for maximising ethylene selectivity and yield.     

Mathematical modelling of the alcoholic fermentation of glucose by Zymomonas mobilis mobilis

The kinetics of alcoholic fermentation of a strain of Zymomonas mobilis, isolated from sugarcane juice, has been studied with the objective of determining the constansts of a non-structured mathematical model that represents the fermentation process. Assays in batch and in continuous culture have been carried out with different initial concentrations of glucose. The final concentrations of glucose, ethanol and biomass were determined. The following kinetic parameters were obtained: μ_max, 0·5 h^?1; K_s, 4·64 g dm^?3; P_max, 106 g dm^?3; Y_x/s, 0·0265 g g^?1; m, 1·4 g g^?1 h^?1; α, 17·38 g g^?1; β, 0·69 g g^?1 h^?1.     

Initial stages of tin electrodeposition from sulfate baths in the presence of gluconate

Tin electrodeposition in its initial stages in acid sulfate/gluconate baths was studied with varying tin and gluconate concentrations using potential-controlled electrochemical techniques. The deposit morphology was observed by scanning electron microscopy (SEM). A comparison with tin electrodeposition from acid sulfate baths in the absence of gluconate was also carried out. Use of a highly acidic bath leads to nonuniform deposits, even in the presence of gluconate; at pH 4 deposits are uniform, brilliant and suitable for finishing applications. Tin crystallites have a well defined morphology which depends on bath agitation conditions. In the absence of agitation, the crystallites have the same tetragonal shape as in a sulfate bath without gluconate.     

Effect of sample size on solvent extraction for detecting cocontinuity in polymer blends

The effect of sample size on the results of solvent extraction measurements for detecting cocontinuity in polymer blends was investigated. Poly(ethylene oxide)/polystyrene (PEO/PS) blend samples of several thicknesses were analyzed by removing the PEO phase using water extraction. The experimental degree of continuity was shown to have a linear dependence on the reciprocal of sample thickness. A model is proposed to explain this dependence and to allow the bulk or true degree of continuity to be determined. Measurement of the bulk degree of continuity is useful for understanding properties of cocontinuous polymer blends such as electrical conductivity, impact strength, or tensile strength.