Influence of the SiC matrix introduction time on the microstructure and mechanical properties of Cf/Hf0.5Zr0.5C-SiC ultra-high temperature composites

C_f/Hf_0.5Zr_0.5C-SiC composites were prepared by introducing Hf_0.5Zr_0.5C matrix (11 cycles) and SiC matrix (9 cycles) into the carbon cloth preform through precursor impregnation and pyrolysis (PIP) process. The influence of the introduction time of SiC matrix on the microstructure and mechanical properties of C_f/Hf_0.5Zr_0.5C-SiC composites was studied, and the results show that with the increase of the PIP cycles of the SiC matrix introduced before Hf_0.5Zr_0.5C matrix, the composite open porosity decreased, and the flexural strength and modulus presented an obvious upward trend. CS45 sample, which has 4 cycles of PIP SiC introduced in advance, has the highest flexural strength, flexural modulus and interfacial shear strength of 402.73 ± 35.73 MPa, 56.92 ± 3.97 GPa and 100.88 ± 7.79 MPa, respectively. Hf_0.5Zr_0.5C matrix has a loose and porous structure, so when more SiC matrix was introduced in advance, its covering effect on the surface of fibers led to less intra-bundle pores and thusly denser composite structure, and due to the compactness of SiC matrix, better overall bonding of fiber, interface and matrix was achieved, as well as better load transfer effect, which led to obvious interfacial debonding and cracking based on the in-situ SEM observation during flexural tests. While in the sample without pre-introduced SiC, the cracking occurred mainly between the interface and porous matrix and the overall performance of the material was poor.     

Asynchronous control for two‐dimensional hidden Markovian jump systems with partly known mode observation conditional probabilities

This study focuses on the asynchronous control problem for two‐dimensional discrete‐time hidden Markovian jump systems where the mode observation conditional probability matrix is partly known. Considering the original system modes are invisible, the observed modes emitted from an observer serve as an alternative for stability analysis and controller design where a mode observation conditional probability matrix is constructed to characterize the emission between system modes and observed modes. Specially, only partly known information of the mode observation conditional probability matrix is accessible. With the introduction of the free‐connection weighting matrices, the asymptotic mean square stability criterion is firstly derived based on Lyapunov method. This introduction provides a further degree of relaxation and less conservatism is therefore achieved. Secondly, we present synthesis conditions for asynchronous state feedback controller design given in terms of a set of interconnected linear matrix inequalities. Moreover, cluster concept based on the partitions of observed modes is adopted which helps to decrease the number of controllers and simplify the design complexity. A numerical example, regarding the cases with and without clustering of the observed modes, is presented to illustrate the effectiveness of the proposed method.     

黄河万家寨河段河冰冰厚遥感提取及年内变化特征分析

冰凌观测是防凌的前提,是冰凌研究的基础,因此全面准确的冰凌观测可为科学防凌提供可靠的依据。为此,以黄河万家寨库区河段为例,通过冰厚反演算法对其冰厚数据进行遥感反演,利用Lebedev模型对反演结果进行验证,并对结果进行年内变化特征分析。结果表明,卫星遥感反演结果与实测及模型验证结果接近,相关系数为0.8;冰厚演变总体呈成冰、流凌、初封、稳封、融冰、开河的生消演变过程。反演冰厚结果可为黄河内蒙段防凌减灾等实际工作提供参考依据。     

影响高空探测质量的原因分析及措施

高空气象探测系统具有较高的探测精度和自动化程度。文章通过对高空探测中影响探测的重放球、迟放球原因的分析,结合工作实践,总结了雷达、计算机、基测箱、探空仪等在运行过程中出现的问题,并提出具体的解决方法,实践证明运行效果显著,为业务人员提供参考。     

Study on maximum power point tracking of photovoltaic array in irregular shadow

Traditional maximum power point tracking (MPPT) methods can hardly find global maximum power point (MPP) because output characteristics curve of photovoltaic (PV) array may have multi local maximum power points in irregular shadow, and thus easily fall into the local maximum power point. To address this drawback, Considering that sliding mode variable structure (SMVS) control strategy have such advantages as simple structure, fast response and strong robustness, and P&O method have the advantages of simple principle and convenient implementation, so a new algorithm combining SMVS control method and P&O method is proposed, besides, PI controller is applied to reduce system chattering caused by switching sliding surface. It is applied to MPPT control of PV array in irregular shadow to solve the problem of multi-peak optimization in partial shadow. In order to verity the rationality of the proposed algorithm, the experimental circuit is built, which achieves MPPT control by means of the proposed algorithm and P&O method. The experimental results show that compared with the traditional P&O algorithm, the proposed algorithm can fast track the global MPP, tracking speed increases by 60% and the relative error decreased by 20%. Moreover, the system becomes more stable near the MPP, the fluctuations of output power is greatly reduced, and thus make full use of solar energy.     

华胜煤业3105综采工作面矿压显现规律研究

针对华胜煤业3105综采工作面受高强度采动影响,围岩稳定难以控制的难题,采用数值模拟与现场实际观测相结合的方法对其采场矿压显现规律进行了分析。结果表明,工作面分别推进到40 m、90 m和120 m时,支承压力的峰值分别在8 m、12 m和15 m左右,影响范围分别在40 m、45 m和45 m左右,最大支承压力分别为8.3 MPa、11.2 MPa和11.6 MPa。3105工作面上部、中部和下部的平均周期来压步距为17.3 m、19.4 m和16 m,工作面的平均周期来压步距为17.6 m;周期来压期间支架的平均末阻力分别为6262.7 kN、7471.6 kN和7580.5 kN,平均值为104.9 kN;影响范围分别为5.4 m、7.4 m、5.8 m,平均值为6.5 m。监测断面顶板累计下沉159.8 mm,两帮累计的相对收敛量达到了92.5 mm。     

Effect of aging time on discontinuous precipitates,continuous precipitates and mechanical properties of AZ80A magnesium alloy

The evolution of precipitates and mechanical properties of AZ80A magnesium alloy with aging time was studied by in situ observation with SEM, TEM and tensile testing. The results show that the continuous precipitation (CP) phases near the reaction front (RF) are replaced by the discontinuous precipitation (DP) phases at the early aging stage. In DP regions, the elliptical phases coarsen obviously with the increase of aging time, which results in a slightly slow reduction of the intracrystalline hardness of DP regions. In CP regions, some small plate phases reprecipitate simultaneously with the growth of the initial precipitates, which contributes to a slight increase in the intracrystalline hardness in CP regions at the later aging stage. The aging hardening of DP regions is faster and stronger than that of CP regions. However, the age strengthening of CP regions not only compensates for the overaging softening of DP regions but also improves the strength of the alloy.     

坚硬顶板下巷道锚网索喷联合支护技术实践

干河煤矿+80水平三采区皮带巷上部赋存坚硬岩层,围岩压力较大;针对坚硬顶板条件,拟定以强主动支护为主的对策,即采用锚网索喷联合支护技术;应用表明,该巷道围岩变形量不大,验证了该支护技术安全可靠。     

Thermally driven failure of Nd:YVO4 amplifier crystals

We report on an unusual failure pattern resulting from thermally driven fracture of laser amplifier single crystals. The pattern led to some confusion with regard to the point of initiation due to the coalescence of hackle lines to a region within the fracture surface, rather than the more common divergence of hackle away from the origin. The pattern leads to new fracture terms: Hackle node - the coalescence of hackle marks to a point of prior compression. The feature is produced as a thermally-generated, centrally-located compressive region transforms to tension thereby drawing crack propagation and hackle to the compressive region, forming an internal terminus. Hackle terminus – a hackle node formed by final crack propagation within the component. As part of the analysis, the fracture toughness and slow crack growth constants of neodymium doped, yttrium ortho-vanadate (Nd:YVO₄) were measured. Nd:YVO₄ exhibits slow crack growth and is very brittle with a fracture toughness of only 0.48 MPa√m.