Inconel 690传热管GTAW对接焊接头组织及力学性能研究

对Inconel 690传热管材进行钨极气体保护焊(GTAW)对接焊,采用拉伸试验机、压扁试验机和光学显微镜测试和分析传热管焊接接头,同时利用ANSYS软件开展焊接接头在设计工况失压时的一次应力强度校核。研究结果表明:焊缝中心为树枝胞状晶,熔合线附近为粗大柱状晶。室温时接头的平均抗拉强度为619 MPa,平均屈服强度为292 MPa,350℃时接头平均抗拉强度为475 MPa,平均屈服强度为206 MPa,拉伸接头断裂从熔合区开始贯穿整个焊缝组织,呈塑性断裂。压扁试验和反向压扁试验结果表明管接头完好。通过ANSYS分析可知,设计工况下传热管接头350℃许用应力强度150 MPa限值可满足其一次应力强度要求,且裕量较大。     

Metal chlorides-promoted ammonia absorption of deep eutectic solvent

Ammonia is considered as a promising hydrogen or energy carrier. Ammonia absorption or adsorption is an important aspect for both ammonia removal, storage and separation applications. To these ends, a wide range of solid and liquid sorbents have been investigated. Among these, the deep eutectic solvent (DES) is emerging as a promising class of ammonia absorbers. Herein, we report a novel type of DES, i.e., metal-containing DESs for ammonia absorption. Specifically, the NH₃ absorption capacity is enhanced by ca. 18.1–36.9% when a small amount of metal chlorides, such as MgCl₂, MnCl₂ etc., are added into a DES composed of resorcinol (Res) and ethylene glycol (EG). To our knowledge, the MgCl₂/Res/EG (0.1:1:2) DES outperforms most of the reported DESs. The excellent NH₃ absorption performances of metal–containing DESs have been attributed to the synergy of Lewis acid–base and hydrogen bonding interactions. Additionally, good reversibility and high NH₃/CO₂ selectivity are achieved over the MgCl₂/Res/EG (0.1:1:2) DES, which enables it to be a potential NH₃ absorber for further investigations.     

Simply constructed highly dispersed cobalt nanoparticles in diverse N-doped graphitic carbon with remarkable performances for water electrolysis

Metal/carbon composite materials are highly promising electrocatalysts for water electrolysis. In this work, three composites of metal cobalt nanoparticles highly dispersed in N-doped carbon materials were facilely constructed by pyrolysis of different phenylenediamine based Schiff base-Co complexes (PDBs). Interestingly, the composites derived from PDBs based on different phenylenediamine exhibited different morphologies. The superior case is that rodlike composite catalyst was derived from o-phenylenediamine based PDBs. The obtained catalyst exhibited remarkable performances for both cathodic hydrogen evolution reaction (HER) and anodic oxygen evolution reaction (OER), as well as overall water electrolysis. Only 172 and 289 mV of overpotentials and 1.57 V of cell voltage were exhibited at 10 mA cm^?2 for HER, OER and water splitting in 1.0 M KOH, respectively. The catalyst also displayed robust stability and high Faraday efficiency, and thus are potential high-performance catalyst for commercial water electrolysis.     

Acid–base transport model depicting the dynamic pH response of interfacial reactions

Acid–base transport is integral to many important interfacial reactions in various fields of chemistry, but its theoretical foundation is lacked. Herein, a common acid–base transport model is established owing to the success in deriving buffer transport equations. This model is applicable to most buffer systems by flexibly integrating the transport equations in terms of buffer components, and is verified through the model relationships of buffer transport limiting current by using hydrogen evolution reaction experiments. Based on model calculations, two diagram approaches are proposed to depict the dynamic pH response and aid buffer operation optimizations. The model and methods allow us to quantify the rate-limiting effect of acid–base transport on interfacial reactions and to precisely control the effect through medium regulations. Furthermore, the model has laid the foundation of dynamic pH effect on species transformation and process mechanism, which can be of wide interest in the chemistry encompassing interfacial reactions.     

Excision of Oxidatively Generated Guanine Lesions by Competitive DNA Repair Pathways

The base and nucleotide excision repair pathways (BER and NER, respectively) are two major mechanisms that remove DNA lesions formed by the reactions of genotoxic intermediates with cellular DNA. It is generally believed that small non-bulky oxidatively generated DNA base modifications are removed by BER pathways, whereas DNA helix-distorting bulky lesions derived from the attack of chemical carcinogens or UV irradiation are repaired by the NER machinery. However, existing and growing experimental evidence indicates that oxidatively generated DNA lesions can be repaired by competitive BER and NER pathways in human cell extracts and intact human cells. Here, we focus on the interplay and competition of BER and NER pathways in excising oxidatively generated guanine lesions site-specifically positioned in plasmid DNA templates constructed by a gapped-vector technology. These experiments demonstrate a significant enhancement of the NER yields in covalently closed circular DNA plasmids (relative to the same, but linearized form of the same plasmid) harboring certain oxidatively generated guanine lesions. The interplay between the BER and NER pathways that remove oxidatively generated guanine lesions are reviewed and discussed in terms of competitive binding of the BER proteins and the DNA damage-sensing NER factor XPC-RAD23B to these lesions.     

Influence of tetraploid wheat (Triticum dicoccum) on low glycaemic index pizza base processing and its starch digestibility

The present study aimed to utilise Dicoccum wheat (DW), barley (BF) and soya flour (SF) in the development of low in vitro starch digestibility (IVSD) and estimated glycaemic index (EGI) PB. The BF and SF are mixed (1:1) (BFSF) and used to replace DW at 25%, 50% and 75% level and compared with 100% DW. The quality characteristics (rheological, physical, textural and chemical), IVSD and EGI of PB were determined. The incorporation of BFSF to DW increased the farinograph water absorption capacity (58.1%–64.2%) and mixing tolerance index (21-68 FU), and decreased the dough development time (4.3–2.8 min) and amylograph pasting properties, respectively. Further, the thickness, shear force and redness were decreased and lightness and yellowness increased. Based on the physico-sensory studies, 50% of BFSF along with emulsifier’s incorporation was optimum without affecting any sensory parameters and this PB had decreased IVSD (31) and EGI (54) when compared to the control 37 and 63, respectively.     

一种使用多跳事实的端到端知识库实体描述生成方法

自动化实体描述生成有助于进一步提升知识图谱的应用价值,而流畅度高是实体描述文本的重要质量指标之一。该文提出使用知识库上多跳的事实来进行实体描述生成,从而贴近人工编撰的实体描述的行文风格,提升实体描述的流畅度。该文使用编码器—解码器框架,提出了一个端到端的神经网络模型,可以编码多跳的事实,并在解码器中使用关注机制对多跳事实进行表示。该文的实验结果表明,与基线模型相比,引入多跳事实后模型的BLEU-2和ROUGE-L等自动化指标分别提升约8.9个百分点和7.3个百分点。     

On the Enzymatic Formation of Metal Base Pairs with Thiolated and pKa-Perturbed Nucleotides

The formation of artificial metal base pairs is an alluring and versatile method for the functionalization of nucleic acids. Access to DNA functionalized with metal base pairs is granted mainly by solid-phase synthesis. An alternative, yet underexplored method, envisions the installation of metal base pairs through the polymerization of modified nucleoside triphosphates. Herein, we have explored the possibility of using thiolated and pK_a-perturbed nucleotides for the enzymatic construction of artificial metal base pairs. The thiolated nucleotides S2C, S6G, and S4T as well as the fluorinated analogue 5FU are readily incorporated opposite a templating S4T nucleotide through the guidance of metal cations. Multiple incorporation of the modified nucleotides along with polymerase bypass of the unnatural base pairs are also possible under certain conditions. The thiolated nucleotides S4T, S4T, S2C, and S6G were also shown to be compatible with the synthesis of modified, high molecular weight single-stranded (ss)DNA products through TdT-mediated tailing reactions. Thus, sulfur-substitution and pK_a perturbation represent alternative strategies for the design of modified nucleotides compatible with the enzymatic construction of metal base pairs.     

OWL‐based acquisition and editing of computer‐interpretable guidelines with the CompGuide editor

Computer‐Interpretable Guidelines (CIGs) are the dominant medium for the delivery of clinical decision support, given the evidence‐based nature of their source material. Therefore, these machine‐readable versions have the ability to improve practitioner performance and conformance to standards, with availability at the point and time of care. The formalisation of Clinical Practice Guideline knowledge in a machine‐readable format is a crucial task to make it suitable for the integration in Clinical Decision Support Systems. However, the current tools for this purpose reveal shortcomings with respect to their ease of use and the support offered during CIG acquisition and editing. In this work, we characterise the current landscape of CIG acquisition tools based on the properties of guideline visualisation, organisation, simplicity, automation, manipulation of knowledge elements, and guideline storage and dissemination. Additionally, we describe the CompGuide Editor, a tool for the acquisition of CIGs in the CompGuide model for Clinical Practice Guidelines that also allows the editing of previously encoded guidelines. The Editor guides the users throughout the process of guideline encoding and does not require proficiency in any programming language. The features of the CIG encoding process are revealed through a comparison with already established tools for CIG acquisition.     

磁感应强度基准技术评述

从不确定度和应用情况等方面介绍了当前磁感应强度量值单位的几类基准,包括基于计算线圈的实物基准、基于核磁共振原理的量子基准和基于质子旋磁比的基本物理常数基准。量子精密测量领域近年来发展迅速,出现了比传统核磁共振基准的准确度更高的原子磁共振量子基准、可以进一步拓展核磁共振基准的量值下限的超导-核磁共振技术等新进展。重点评述了现有的磁感应强度的量子基准,并介绍了一些有望进一步拓展磁学计量前沿的新进展。