农村综合能源系统多层协同优化运行方法

农村综合能源系统通过多种能源的协同互补,在满足农村用户多元化用能需求的同时,能有效提升能源利用效率和用能经济性。首先,在考虑适应农村典型场景的基础上,提出了一种三层协同自律的农村综合能源分层协同运行优化框架。然后,基于农村综合能源系统典型设备,建立了三层农村综合能源系统源-储-荷联合优化调度模型以及相应的优化调度流程。调度模型中冬季通过对沼气发电机组的余热回收与空气源热泵协同对用户供热;夏季对沼气发电机组余热进行回收,并通过溴化锂制冷机与空气源热泵联合对农村用户供冷。最后,对农村综合能源系统多层协同优化方法进行了算例分析,结果表明该优化方法提高了农村居民用能的经济性,验证了所提方法的有效性。     

Analytical Modeling for Translating Statistical Changes to Circuit Variability by Ultra-Deep Submicron Digital Circuit Design

This paper presents a physics-based compact gate delay model that includes all short-channel phenomena prevalent at the ultra-deep submicron technology node of 32 nm. To simplify calculations, the proposed model is connected to a compact α-power law-based (Sakurai-Newton) model. The model has been tested on a wide range of supply voltages. The model accurately predicts nominal delays and the delays under process variations. It has been shown that at lower technology nodes, the delay is more sensitive to threshold voltage variations, specifically at the sub-threshold operating region as compared with effective channel length variations above the threshold region.     

Measurement of residual stresses in dissimilar friction stir-welded aluminium and copper plates using the contour method

The longitudinal residual stresses in the friction stir-welded plates of 5A06 aluminium and pure copper were determined using the contour method. The results revealed the presence of high tensile and compressive residual stresses on the aluminium and copper sides, respectively. The residual stresses were detected on the weld zone as well as the thermo-mechanically affected zone (TMAZ) of the aluminium plate. In contrast, the compressive residual stresses in the copper plate had a much narrower width along the weld line. Peak tensile stresses up to 240?MPa were found in the TMAZ of the aluminium plate.     

Kevlar织物软壁包容环抗冲击数值仿真分析研究

针对机匣包容性问题,提出Kevlar平纹织物本构模型的拟合方法,分别采用单层壳、多层壳、层合壳三种有限元建模方式对Kevlar织物软壁包容环弹道冲击过程进行模拟,发展了机匣包容性仿真分析模型。结果表明,多层壳模型和层合壳模型的计算结果更准确,并且可以通过调节摩擦因子使仿真结果与试验结果更接近。在此基础上研究了撞击点位置和弹体入射姿态对弹体剩余速度的影响。结果表明:在较小偏移距离内,撞击点的位置对剩余速度的影响可以忽略不计;滚转角和俯仰角对剩余速度影响较小,而对于偏航角,当角度大于30°时,剩余速度会随着角度的增大明显呈下降趋势,且弹体出射姿态也会发生明显变化。     

Delay compensated control of the Stefan problem and robustness to delay mismatch

This paper presents a control design for the one‐phase Stefan problem under actuator delay via a backstepping method. The Stefan problem represents a liquid‐solid phase change phenomenon which describes the time evolution of a material's temperature profile and the interface position. The actuator delay is modeled by a first‐order hyperbolic partial differential equation (PDE), resulting in a cascaded transport‐diffusion PDE system defined on a time‐varying spatial domain described by an ordinary differential equation (ODE). Two nonlinear backstepping transformations are utilized for the control design. The setpoint restriction is given to guarantee a physical constraint on the proposed controller for the melting process. This constraint ensures the exponential convergence of the moving interface to a setpoint and the exponential stability of the temperature equilibrium profile and the delayed controller in the norm. Furthermore, robustness analysis with respect to the delay mismatch between the plant and the controller is studied, which provides analogous results to the exact compensation by restricting the control gain.     

宁夏红寺堡盆地隐伏古隆起成因机制及其对区域沙漠化的影响

目前对于青藏高原东北缘活动构造研究多集中于活动断裂带的活动性,而对夹持于其间的沉积盆地构造格架及活动性研究甚少。以夹持于烟筒山断裂与牛首山—罗山断裂之间的宁夏红寺堡盆地为研究对象,采用重力资料重处理解译、音频大地电磁测深(AMT)和地震勘探相结合,揭示红寺堡盆地隐伏构造特征,并进一步采用盆山一体化思路分析隐伏构造的成因机制及其对区域沙漠化的控制作用。结果表明:青藏高原在中新世末发生强烈的NE向推挤、扩展和隆升,红寺堡盆地由坳陷盆地转变为挠曲盆地; 在青藏高原NE向扩展的影响下,烟筒山断裂发生强烈的逆冲作用,古生代—中生代基底逆冲于古近系—新近系之上,受构造变形影响的最新地层为中新统彰恩堡组; 红寺堡盆地内的隐伏古隆起呈NW—SE向,与烟筒山构造带具有相同的构造动力学背景,受青藏高原NE向扩展影响形成于中新世末,并且至今仍具有活动性; 隐伏古隆起周缘断裂的活动破坏了地表稳定性、蓄水能力和地表植被,导致区域沙漠化呈现有规律的NW—SE向带状展布。该研究成果对于宁夏红寺堡盆地区域稳定性评价及沙漠化的综合治理具有现实指导意义。     

An expectation operator for belief functions in the Dempster–Shafer theory*

ABSTRACT

The main contribution of this paper is a new definition of expected value of belief functions in the Dempster–Shafer (D–S) theory of evidence. Our definition shares many of the properties of the expectation operator in probability theory. Also, for Bayesian belief functions, our definition provides the same expected value as the probabilistic expectation operator. A traditional method of computing expected of real-valued functions is to first transform a D–S belief function to a corresponding probability mass function, and then use the expectation operator for probability mass functions. Transforming a belief function to a probability function involves loss of information. Our expectation operator works directly with D–S belief functions. Another definition is using Choquet integration, which assumes belief functions are credal sets, i.e. convex sets of probability mass functions. Credal sets semantics are incompatible with Dempster's combination rule, the center-piece of the D–S theory. In general, our definition provides different expected values than, e.g. if we use probabilistic expectation using the pignistic transform or the plausibility transform of a belief function. Using our definition of expectation, we provide new definitions of variance, covariance, correlation, and other higher moments and describe their properties.     

顶空-气相色谱法测定食品接触材料中14种溶剂残留量

建立顶空-气相色谱法测定食品接触材料（纸基食品接触材料和涂漆筷子等）中14种溶剂残留量的前处理分析方法。方法 通过优化溶剂基质和体积、氮气和空气、样品面积和碎片大小等前处理条件，实现了对14种溶剂残留量的常规、快速分析。结果 14种溶剂残留量在0.01~6.40 mg/m2浓度范围内, 线性相关系数均大于0.9970，方法检出限为0.01mg/m2。结论 建立了适用于纸基食品接触材料和涂漆筷子等食品接触材料前处理方法和仪器分析方法，对食品接触材料产品研究和提高企业产品质量提供依据。     

再加工工艺对N18锆合金板残余应力的影响

采用“热轧+冷轧+退火”工艺对N18锆合金板进行再加工,通过X射线法分析板的表面残余应力,采用EBSD技术分析晶界取向差角分布和大小角度晶界。结果表明,热轧后N18锆合金板的表面残余应力呈现无规律分布状态;冷轧后板的表面残余应力均为压应力,其大小随着冷轧变形量的增加而增加;退火后板的表面残余应力值处于较低水平,当退火制度为500 ℃×2 h时,残余应力处于最低水平;退火后,板的微观结构以小角度晶界为主,且随着退火温度的升高,小角度晶界的密度先增加后趋于稳定。     

Effect of cutting process on the stress corrosion susceptibility of AISI 304L stainless steel

During manufacturing of a component, cutting, turning, grinding, and milling operations are inevitable and these operations induce surface residual stresses. In this study, it is shown that, depending on the process employed for cutting, residual stresses generated at the cut surfaces can vary widely and they can, in turn, make the cut surfaces of austenitic stainless steel (SS) prone to stress corrosion cracking (SCC). An austenitic SS 304L plate was cut using three different procesess: bandsaw cutting, cutting using the cut-off wheel, and shearing. Surface residual stress measurement using the X-ray diffraction (XRD) technique is carried out close to the cutting edges and on the cross-section. SCC susceptibility studies were carried out as per ASTM G36 in 45% boiling magnesium chloride solution. Optical microscopic examination showed the presence of cracks, and confocal microscopy was used to measure the depth of cracks. The study confirmed that high tensile residual stresses present in the cut surfaces produced by cut-off wheel and shear cutting make the surfaces susceptible to SCC while the surfaces produced by bandsaw cutting are resistant to SCC. Hence, it is shown that there is a definite risk of SCC for product forms of austenitic SS with cut surfaces produced using cutting processes that generate high tensile residual stresses stored for a long period of time in a susceptible environment.