铝冷轧制油应用和生产工艺研究

通过对铝材冷轧工艺的分析。研究，以退火工艺中的斑痕为重点，提出采用加氢处理，异构化精制的石蜡基航空煤油组分为基础油，采用不同复合添加剂生产的通用铝冷轧制油完全可以满足客户要求。     

深孔钻机水刹车传动机构的设计改进

针对深孔钻机水刹车传动机构原设计结构中存在的问题进行分析、研究、并对机构进行了改进，满足了钻机绞车的各项性能指标和技术要求。     

医用聚氯乙烯材料的表面光接枝改性

研究了在不排氧氛围下 ,紫外光照射 ,以二苯甲酮 (BP)为光引发剂 ,甲基丙烯酸缩水甘油酯(GMA)在医用聚氯乙烯 (PVC)薄膜表面的气相接枝聚合。探讨了反应条件对接枝结果的影响 ,并用正交法指出了影响因素的显著性。用傅立叶红外 (FT- IR)、水接触角作为接枝改性结果的表征。FT- IR谱图表明 GMA已接枝到 PVC膜表面。水接触角由接枝前的 78°下降到 5 4°     

Inhibition of acid rock drainage from uranium ore waste using a conventional neutralization and precipitation treatment

Glass columns (length 50 cm, i.d. 4 cm) containing 900 g of uranium ore waste were subjected to a three-step process: (1) acid drainage generation, (2) neutralization and precipitation treatment and, again, (3) acid drainage generation. In the first acid generation step, lasting about one year, different variables (pyrite addition, inoculation and irrigation solution) were tested by measuring effluent pH, redox potential, total iron and sulphate. Conditions of acid generation were satisfactorily reproduced, reaching stable pH values around 2.0 that were determined mainly by pyrite addition and the type of irrigation solution used (distilled water or ferrous sulphate). The neutralization and precipitation treatment consisted of alternating irrigations of a neutralizing solution (CaO saturated plus NaOH) and a precipitating solution (ferric sulphate saturated). This treatment caused accumulation of basic iron sulphate and iron oxide precipitates according to SEM studies. After this treatment, the barrier effect created by the reaction products was checked, using irrigation solutions similar to the first step. The effluents collected showed higher pH and lower redox potential, total iron and sulphate values than those observed before the treatment, evidencing inhibition of acid drainage generation.     

旋风分离器结构改进的研究

根据旋风分离器的工作原理及应用特点 ,分析了影响旋风分离器分离效率的因素及结构存在的问题 ,并提出了改进措施 ,即内管外壁增设螺旋翼片 ,扩散形锥体改为悬挂挡板。通过实验观察 ,改进结构的旋风分离器分离效率比常规旋风分离器高。实践证明 ,对于密度差异较小的非均相物系的分离 ,只要对旋风分离器作适当改进 ,仍能取得令人满意的效果 ,这大大拓宽了旋风分离器的应用领域     

Adhesive element modelling and weighted static shape control of composite plates with piezoelectric actuator patches

A novel finite element model is presented for static and dynamic analysis of composite plates integrated with a laminated piezoelectric layer, a host laminated composite plate and an adhesive layer between them. A new adhesive element is developed which includes both peel and shear effects in the adhesive layer based on first‐order shear deformation plate theory. The thin adhesive layer between the piezoelectric layer and the host plate is modelled by assuming that it carries constant shear and peel strains throughout its thickness. In addition, a weighted static shape control scheme for finding the optimal voltage distribution for static shape control is given. By selecting different weighting matrices, a variety of items such as displacements, slopes, curvatures, strains and even generalized forces, can be included in finding the optimal actuating voltage for static shape control. The present model is validated by comparing with those results available in the literature. The numerical results show that the weighted linear least method can give a satisfactory voltage distribution to best match the desired shape. Copyright © 2004 John Wiley & Sons, Ltd.     

Terminal velocity of non-spherical particles falling through a Carreau model liquid

A procedure has been proposed for the estimation of the terminal falling velocity of non-spherical particles moving in a Carreau model fluid in the transition flow region. The procedure is based on a modification of the relationship formerly developed for the fall of spherical particles including the particle dynamic shape factor. The suitability of the proposed procedure has been confirmed by good agreement between experimental and calculated terminal falling velocity data. In the experiments, the terminal falling velocity of short cylinders and rectangular prisms in polymer solutions of different measure of shear thinning and elasticity has been measured.     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.